喷射时刻对柴油甲醇组合燃烧发动机颗粒物排放的影响

为了进一步减少甲醇掺烧后的柴油机颗粒物排放,在一台由增压中冷的高压共轨柴油机改造成的柴油甲醇组合燃烧(DMCC—diesel/methanol compound combustion)发动机上详细研究了柴油喷射时刻对两种燃料共燃时的颗粒物生成及其排放的影响.试验工况选择重型柴油机常用的A50工况.试验结果表明,当柴油在上止点后喷射时,颗粒物排放的数量浓度随着甲醇替代率的增加而减少,当上止点前喷射时,颗粒物的数量浓度先减少后增加.随着喷射时刻的提前,颗粒中超细颗粒所占比例增大.随着喷射时刻的推迟,甲醇替代率降低颗粒物质量浓度的作用增强,同时甲醇替代率降低颗粒物几何平均直径的作用减弱.     

岩体开挖卸荷过程力学特性分析

基于岩体开挖卸荷过程中力学参数变化理论的分析研究,建立卸荷岩体有限元分析模型,运用ADINA有限元分析软件对岩体进行一维卸荷数值仿真研究。根据有限元数值分析计算成果得到岩体力学参数与主卸荷方向累计开挖卸荷量间的变化关系曲线。结果表明:岩体开挖卸荷过程中,岩体力学参数变形模量、泊松比、粘聚力和内摩擦角等呈现出随开挖卸荷量的变化而发生变化的特征,随卸荷量的增大有减小的趋势,但它们不是从初始值一直减小到零,而是随卸荷量的增大减小到一定的量值后,岩体的裂隙张开、结构面的扩展到一定的程度,岩体的力学参数保持一定的量级不再减小。     

Comparative study on effect of blending,thermal barrier coating (LHR) and injector nozzle geometry on biodiesel-fuelled engines

Increased petroleum prices, increased threat to the environment from exhaust emissions and global warming have generated intense international interest in developing renewable and alternative non-petroleum fuels for internal combustion engines. Evolving suitable technology for addressing energy crisis creates a continued investigation into the search for sustainable and clean-burning renewable fuels. This work investigates suitability of different non-edible-derived biodiesels such as cotton seed oil methyl ester (COME), Honne oil methyl ester (HnOME) and Rubber seed oil methyl ester (RuOME) to four stroke, single cylinder compression ignition (CI) engine. Engine tests were conducted to study the effect of fuel blending, thermal barrier coating (TBC) or Low Heat Rejection (LHR) and injector nozzle geometry on the performance, combustion and emission characteristics of COME, HnOME and RuOME in the modified CI engine. Blends of biodiesels with diesel were varied from 20 to 80% in steps of 20%. Two thermal barrier coatings of partially stabilized zirconium (PSZ) and aluminium oxide (Al₂O₃) were provided on the engine to make it fully adiabatic. Nozzle injectors of 3, 4 and 5 holes, with size of orifice varied from 0.2 to 0.3 mm size were selected for the study. It was concluded that B20 biodiesel blend, PSZ-coated engine and four hole nozzle injector of 0.2 mm size resulted in overall better engine performance with increased brake thermal efficiency (BTE) and reduced HC, CO, smoke emissions for the fuel combinations tested. Combustion analysis to study the effect of biodiesel blends, LHR coatings, injector nozzle geometry on the performance of the biodiesel-fuelled engine has been presented to give more insight into the behaviour of operation.     

An experimental apparatus for testing biodiesels based on a CFR engine—setup and validation with different methyl ester blends

A cooperative fuel research (CFR) engine was modified and instrumented in order to control operating conditions and to measure engine parameters and in-cylinder pressure diagrams. Aiming at the comparison of different alternative fuels, an experimental procedure was defined, including cetane number (CN) evaluation and the definition of engine operating quantities in different working points, for fixed levels of compression ratio (CR) and injection advance. An investigation was made considering several blends of methyl-esters of rapeseed oil (RME) and of a mix of vegetable oils (VOME) with conventional diesel oil. The defined experimental procedure was applied to assess CN, engine brake thermal efficiency (bte) and exhaust emissions. Results show that the biodiesel content has a positive influence on soot emissions, with strong reduction, while thermal efficiency and NO_X emissions are negatively affected, which can be justified taking into account fuel properties and changes in combustion process. As observed outcomes are generally in line with those presented in literature, the facility proved to be a suitable tool for basic investigations on alternative fuels to be used in specific applications.     

A numerical study on the effects of EGR and spark timing to combustion characteristics and NOx emission of a GDI engine

EGR is one of the most significant strategies for reducing especially nitrogen oxides (NO_x) emissions from internal combustion engines. The thermal efficiency of spark ignition engines is lower than compression ignition engines because of its lower compression ratio. If the compression ratio is increased to obtain higher thermal efficiency, there may be a knocking tendency in spark ignition engines. EGR can be used in order to reduce NO_x emissions and avoid knocking phenomena at higher compression ratios. In-cylinder temperature at the end of combustion is decreased and heat capacity of fresh charge is increased when EGR applied. Besides EGR, spark timing is another significant parameter for reducing exhaust emissions such as nitrogen oxides, and unburned hydrocarbon (UHC). In this study the effects of EGR and spark timing on spark ignition engine were investigated numerically. KIVA codes were used in order to model combustion process. The combustion process has been modeled for a single cylinder, four stroke and gasoline direct injection (GDI) spark ignition engine. The results showed that in-cylinder pressure and heat release rate decrease as EGR ratio increase. In-cylinder pressure increases with the advancing of spark timing. Advancing spark timing increases the heat release rate and in-cylinder temperature. The simulation results also showed that EGR reduced exhaust gas temperature and NO_x emissions.     

Comprehensive Environmental Investigation at Former Industrial/Petroleum Underground Storage Tank Sites in Long Beach,CA: A Forensic Perspective

Two industrial sites were investigated based on years of available hydrogeologic information and monitoring data for soil and groundwater. Collected data were forensically evaluated using age-dating and fingerprinting methods. The previous business uses of the project sites were as a gas station, laundry/dry-cleaning service, and car wash with petroleum underground storage tanks (USTs). As a result, these sites were exposed to a number of toxic contaminants at relatively high concentrations. Source control was necessary for successful remediation and the ultimate removal of the remaining compounds from these industrial sites. Although contaminated soil around the source was excavated during the remedial action and the high concentrations of contaminants were reduced, typical groundwater contaminants such as petroleum hydrocarbons as gasoline (TPH-G), benzene, toluene, ethylbenzene, xylenes (BTEX), and oxygenates including methyl tert-butyl ether (MTBE), diisopropyl ether (DIPE), ethyl tert-butyl ether (ETBE), tert-amyl methyl ether (TAME), and tert-butyl alcohol (TBA) were persistently found at the studied sites around the source points. The plume and concentration of contaminants had changed their shapes and strength for all monitoring periods. Thus, additional source control seems to be a requirement for the complete removal of source contamination, which must be ascertained with groundwater and soil monitoring on a regular time base. For the study sites, monitored natural attenuation was relatively feasible for the long-term plan; however, it did not offer a perfect remediation solution for an ultimate goal because of residual toxic compounds that might have affected the surrounding residential areas at higher concentrations than their health limits. Therefore, as a remediation strategy, the combination of clean-up technology and natural attenuation with monitoring activities are more highly recommended than either clean-up or natural attenuation used separately.     

微波消解-流动注射分光光度法测定总氮和总磷

以碱性过硫酸钾溶液为消解液,采用微波消解-流动注射分光光度法测定水中总氮和总磷。在碱性过硫酸钾溶液中氢氧化钠质量浓度为9.6g/L、微波功率为320W、消解管长度为16m的条件下,总氮和总磷的检出限分别为0.040m g/L和0.020mg/L,线性范围分别为0.040～3.500mg/L和0.020～2.500mg/L,相对标准偏差分别为1.6%和1.0%。微波消解-流动注射分光光度法应用于河水、湖水、化工废水等实际水样中总氮和总磷的测定,加标回收率分别为95.7%～98.1%和97.2%～102.2%。     

流动注射分光光度法测定水中铝的含量

以桑色素作显色剂,采用流动注射分光光度法测定水中铝的含量。在桑色素质量浓度为0．8g／L、聚氧乙烯辛基苯基醚体积分数为1．0％、进样环体积为400μL、检测波长420nm的条件下,采用流动注射分光光度法对水中铝的含量进行测定,本方法的线性范围为2～300μg／L,检出限（信噪比为3）为0．124μg／L,相对标准偏差为2．9％,加标回收率为96．4％～101．8％。     

汽油机冷启动时燃油蒸发多参数影响研究

采用CFD商用软件STAR-CD对汽油机冷启动过程中燃油蒸发进行三维数值模拟,研究了油滴初直径、油滴初速度、进气温度、燃油温度、喷射定时和转速对燃油蒸发率的影响规律.计算结果表明,进气温度、燃油温度和转速对燃油蒸发有重要影响.进气门开时,在进气温度为-7℃和90℃时,蒸发率分别为5.7%和25.0%;相应地,在燃油温度为0℃和60℃时,燃油蒸发率分别为5.7%和22.0%.油滴初直径和喷射定时对燃油蒸发率有一定影响,油滴初速度对燃油蒸发率影响很小.     

微波联合消解流动注射光度法测定水中总氮和总磷

利用微波联合消解水样,采用流动注射分析技术,建立了在线测定水中总氮和总磷的快速分析方法.优化了试验条件,在线性范围内,总氮和总磷的工作曲线线性关系良好,检出限分别为0.03 mg/L和0.01 mg/L,相对标准偏差分别为1.5%和1.2%,加标回收率分别为96.7%～103%和98.8%～102%.