GO-TiO2改性中空纤维膜的制备条件及抗污染性能研究

以氧化石墨烯(GO)与纳米二氧化钛(TiO_2)为改性剂,采用界面聚合法与抽滤吸附结合,对聚偏氟乙烯中空纤维超滤膜(简称原膜)进行表面改性,得到新型纳米改性膜(简称GO-TiO_2改性膜).研究改性膜的制备工艺条件及其对腐殖酸(HA)的吸附截留性能与抗污染特性.结果表明:(1)最佳制备工艺条件为:钛酸丁酯2 m L、GO 1 mg、间苯二胺1%(质量分数)、间苯二胺浸泡时间8 min、均苯三甲酰氯0.2%(质量分数)、均苯三甲酰氯浸泡时间10 min;(2)亲水性提高显著,亲水性表面为GO-聚酰胺-TiO_2复合结构,改性膜接触角由80.6°±1.8°下降到38.6°±1.2°;(3)抗污染性能提高明显.改性膜通量总衰减率由改性前的51.2%下降到35.6%,过滤周期约为原膜的2.5倍;反冲洗后膜通量恢复率由69%提高到96%.     

水平对置活塞发动机高空热平衡特性研究

目的研究不同海拔大气压力特别是高空条件对水平对置活塞汽油机热平衡性能的影响。方法利用内燃机高空模拟试验台进行不同海拔高度(0~7000 m)下水平对置活塞汽油机的热平衡试验,测得不同海拔下排温、缸体表面温度等特征参数,计算热流量分配特性,并对比分析热流量分配特性随海拔高度的变化规律。结果随海拔升高,汽油机排温和缸体表面温度逐渐下降,且海拔愈高,缸体表面温度下降幅度愈大。汽油机有效功率随海拔升高逐渐下降,余项损失百分比逐渐上升,且在低转速下,变化幅度增大。在6000 m模拟海拔、3000 r/min转速下,汽油机有效热效率不到5%,而余项损失达到了30%以上,此时部分汽油甚至并未燃烧。结论高空环境对水平对置汽油机热平衡性能造成严重影响,成为制约其高海拔性能恢复的关键因素。     

珠江三角洲轻型汽油车匀速状态挥发性有机物排放特征研究

以18辆轻型汽油车(LDGVs)为研究对象,利用底盘测功机搭建挥发性有机物(VOCs)采样系统.利用气相色谱-质谱仪(GC-MS)和高效液相色谱(HPLC)识别了匀速25 km·h~(-1)时尾气VOCs化学成分谱和排放因子,并在分析时考虑了排放标准、行驶工况和车辆属性等因素的影响.结果表明,轻型汽油车低速匀速工况下尾气组成以烷烃(40.8%,C_5～C_7烷烃较多)为主,其次是芳香烃(29.5%)和含氧VOCs(26.0%),烯炔烃(3.6%)和卤代烃(0.1%)较少.其中,甲醛、异戊烷、甲苯、苯、间/对二甲苯、丙酮、2-甲基戊烷、正戊烷、1,2,4-三甲基苯和壬醛是比例最高的物质(52.01%).低速匀速行驶中生成了比例更低的烯烃和比例更高的C_5～C_7烷烃和OVOCs.排放标准为国III、IV和V的轻型汽油车在低速匀速工况下,VOCs排放因子分别为(50.12±46.83)、(40.26±31.15)和(3.25±0.65) mg·km~(-1).国IV到国V车的烷烃、烯炔烃、芳香烃、卤代烃和总VOCs降幅均超过88%,而OVOCs降幅只有约55%,说明OVOCs在国V车的排放富集程度更高.总体来讲,国V车排放的VOCs反应活性约为国IV车排放的VOCs反应活性的11%.车辆属性对VOCs排放的影响表现为:年份、里程和排量的增加会促进VOCs排放的整体增加,而基准质量对VOCs排放的影响相对较小.     

满足国五排放标准的柴油甲醇双燃料发动机非常规排放研究

在一台装备有电控单体泵增压中冷系统柴油机的进气管上,加装甲醇喷射装置并向进气道喷入定量的纯甲醇,结合废气再循环(EGR)技术并使用氧化催化转化器(DOC)组合微粒氧化催化器(POC)后处理系统,使其常规排放能满足国五排放法规基础上,全面研究了柴油甲醇双燃料(Diesel Methanol Dual Fuel,DMDF)发动机的非常规排放特性.在采用国五排放法规标准规定的ESC(稳态13点工况)测试方法条件下,利用FTIR(傅里叶变换红外检测法)对DMDF发动机的检测结果表明:该机非常规排放物主要为甲醇、甲醛、1,3-丁二烯、苯、甲苯和SO2,非常规排放物的全工况加权比排放为19.532 g·kW~(-1)·h~(-1),其中,甲醇的全工况加权比排放为11.395 g·kW~(-1)·h~(-1),甲醛的全工况加权比排放为5.927g·kW~(-1)·h~(-1),SO2的全工况加权比排放为0.053 g·kW~(-1)·h~(-1),其余排放物为痕量水平.在催化氧化装置处理后非常规排放物全工况加权比排放为0.115 g·kW~(-1)·h~(-1),降幅为99.41%.催化氧化装置对甲醇、1,3-丁二烯、苯和甲苯的消除率为100%,对甲醛的消除率为99.04%.     

BED含氧燃料在不同海拔下对柴油机PM和NOx排放的影响

为研究生物柴油-乙醇-柴油(简称为BED)含氧燃料在不同海拔下对柴油机微粒(PM)和氮氧化物(NO_x)排放的影响,在一台高压共轨柴油机上分别燃用纯柴油和BED含氧燃料,在两种大气压力(81和100 k Pa)下进行了排放试验研究.结果表明,燃用纯柴油和B15E5(15%生物柴油+5%乙醇+80%柴油,体积比)燃料后,在中、低负荷时的PM排放在高气压下基本高于低气压下,最高增幅分别达到26.2%和19.0%;在全负荷时的PM排放在高气压下降低,最高降幅分别达到6.1%和17.0%.燃用B25E5(25%生物柴油+5%乙醇+70%柴油,体积比)燃料后,PM排放在高气压下降低.燃用纯柴油后,柴油机在高气压下的NO_x排放低于低气压下;燃用B15E5和B25E5含氧燃料后,在中、低负荷下的NO_x排放在高气压下降低,在全负荷下的NO_x排放在高气压下升高.在中、低负荷下NO_x排放最高降幅分别达到12.1%和15.3%;在全负荷下,NO_x排放最高增幅分别达到6.5%和5.8%.在不同大气压力下,柴油机燃用纯柴油和BED含氧燃料后,PM与NO_x排放均呈现明显的trade-off关系.相比于在低气压下,随负荷增加引起的PM排放降幅和NO_x排放增幅在高气压下增加.     

Fractionation of residual Al in natural water treatment from reservoir with poly-aluminum-silicate-chloride (PASiC): Effect of OH/Al, Si/Al molar ratios and initial pH

An aluminum fractionation study was conducted for a surface reservoir water treatment to understand the performance of poly-aluminum-silicate-chloride (PASiC) in terms of the residual Al fractions as a function of initial pH. The coagulation performance expressed as turbidity and organic matter removal was established as supporting data. Some extra data were evaluated in terms of the residual Al ratio of the composite PASiC coagulant. The main residual Al sources were the Al fractions derived from the use of PASiC. The turbidity and organic matter removal ability was optimal at initial pH 6.00-7.00, while the concentrations of various residual Al species and the residual Al ratio of PASiC were minimal at an initial pH range of 7.00-8.00. Under the conditions of OH/Al molar ratio = 2.00 and Si/Al molar ratio = 0.05, PASiC had superior coagulation performance and comparatively low residual Al concentrations. The Al fraction in the composite PASiC coagulant seldom remained under such conditions. Experimental data also indicated that the suspended (filterable) Al fraction was the dominant species, and organic-bound or organo-Al complex Al was considered to be the major species of dissolved Al in water treated by PASiC coagulation. Additionally, the dissolved inorganic monomeric Al species dominated the dissolved monomeric Al fraction.     

锈蚀钢结构连接节点抗震性能研究进展

基于材料与连接构件层面,总结了近年来国内外既有试验研究及理论分析成果,主要包括腐蚀后的标准试件的单调拉伸、滞回性能退化分析,以及梁柱节点、框架结构的抗震性能研究,并给出了相应的力学性能退化模型,通过进行总结及对比分析后,为复杂环境下工程钢结构给出研究方向,同时也对我国工程结构的设计方法提供理论指导和参考依据。     

混燃甲醇和乙醇改善柴油机碳烟排放

以柴油机为基础，以乙醇或甲醇作为预混合燃料，与喷入的柴油组成部分预混的复合燃烧，大幅度降低了发动机排气烟度，同时使氮氧化物排放得到一定改善，发动机的燃油消耗率优于原柴油机，而HC排放，尤其是在低负荷时有所增加，甲醇比乙醇具有降低烟度效果更好、氮氧化物降低更多和HC及CO排入增加较少的优越性。     

钢铁企业用涤纶滤料的性能试验研究

选取钢铁企业用覆膜和未覆膜涤纶针刺毡滤料进行实验研究,测试了两种滤料的力学特性、耐腐蚀特性和过滤性能。结果表明:清洁的覆膜涤纶针刺毡过滤阻力比未覆膜涤纶针刺毡的阻力高8~10倍,但是覆膜涤纶针刺毡的最低过滤效率比未覆膜涤纶针刺毡的高49.9%;在20%、40%的H_2SO_4中浸泡24 h后经、纬向断裂强力和伸长保持率均维持在80%以上,在40%的NaOH溶液中浸泡24 h后的断裂强力保持率在8%以下,因此两种滤料具有良好的耐酸腐蚀性,但不适合在强碱条件下长期使用。     

Potential of secondary aerosol formation from Chinese gasoline engine exhaust

Light-duty gasoline vehicles have drawn public attention in China due to their significant primary emissions of particulate matter and volatile organic compounds(VOCs). However,little information on secondary aerosol formation from exhaust for Chinese vehicles and fuel conditions is available. In this study, chamber experiments were conducted to quantify the potential of secondary aerosol formation from the exhaust of a port fuel injection gasoline engine. The engine and fuel used are common in the Chinese market, and the fuel satisfies the China V gasoline fuel standard. Substantial secondary aerosol formation was observed during a 4–5 hr simulation, which was estimated to represent more than 10 days of equivalent atmospheric photo-oxidation in Beijing. As a consequence, the extreme case secondary organic aerosol(SOA) production was 426 ± 85 mg/kg-fuel, with high levels of precursors and OH exposure. The low hygroscopicity of the aerosols formed inside the chamber suggests that SOA was the dominant chemical composition. Fourteen percent of SOA measured in the chamber experiments could be explained through the oxidation of speciated single-ring aromatics. Unspeciated precursors, such as intermediate-volatility organic compounds and semi-volatile organic compounds, might be significant for SOA formation from gasoline VOCs. We concluded that reductions of emissions of aerosol precursor gases from vehicles are essential to mediate pollution in China.