气相色谱法测定二硫化碳和甲硫醚

利用气相色谱(配火焰光度检测器,采用3mxφ2mm玻璃填充柱分离)对CS2和甲硫醚(DMS)两种含硫化合物进行了分离检测。该方法具有较高的灵敏度和良好的线性关系。结果表明:该分析对含硫气体的最小检测浓度在mg/m3级,在柱温为70℃,检测器温度为180℃,气化室温度为150℃,氮气流速为50mL/min时,CS2的回收率为98.66%,变异系数为2.12%;甲硫醚的回收率为98.66%,变异系数为1.56%。     

脉冲电晕等离子体脱硫脱氮与除尘技术

脉冲电晕放电是产生等离子体的方法之一，目前已达到工业性试验阶段，该文对脉冲电晕等离子脱硫脱氮与除尘技术的形成过程进行了回顾，对其理论作了分析，并简介了工艺流程，还指出了目前存在的主要问题和需研究的关键技术。     

泉州湾滩涂沉积物对Cu（Ⅱ）的吸附实验

研究了Cu(Ⅱ)在泉州湾滩涂沉积物上的吸附行为。探讨了pH和温度对吸附作用的影响，测定了其吸附等温线。实验结果表明，常温下Cu(Ⅱ)在泉州湾滩涂沉积物上的吸附平衡时间约需3．5小时；吸附量随pH的升高先增大而后减少，pH=6．0左右时达最大；吸附量随温度的升高而增大；其吸附行为可以很好地用Langmuir型吸附等温线来描述。并在此基础上初步探讨了Cu(Ⅱ)在泉州湾滩涂沉积物上的吸附机理。     

Developing Canada's National Forest Carbon Monitoring, Accounting and Reporting System to Meet the Reporting Requirements of the Kyoto Protocol

The rate of carbon accumulation in the atmosphere can be reduced by decreasing emissions from the burning of fossil fuels and by increasing the net uptake (or reducing the net loss) of carbon in terrestrial (and aquatic) ecosystems. The Kyoto Protocol addresses both the release and uptake of carbon. Canada is developing a National Forest Carbon Monitoring, Accounting and Reporting System in support of its international obligations to report greenhouse gas sources and sinks. This system employs forest-inventory data, growth and yield information, and statistics on natural disturbances, management actions and land-use change to estimate forest carbon stocks, changes in carbon stocks, and emissions of non-CO₂ greenhouse gases. A key component of the system is the Carbon Budget Model of the Canadian Forest Sector (CBM-CFS). The model is undergoing extensive revisions to enable analyses at four spatial scales (national, provincial, forest management unit and stand) and in annual time steps. The model and the supporting databases can be used to assess carbon-stock changes between 1990 and the present, and to predict future carbon-stock changes based on scenarios of future disturbance rates and management actions.     

Carbon Dioxide Balance of Wood Substitution: Comparing Concrete- and Wood-Framed Buildings

In this study a method is suggested to compare the net carbon dioxide (CO₂) emission from the construction of concrete- and wood-framed buildings. The method is then applied to two buildings in Sweden and Finland constructed with wood frames, compared with functionally equivalent buildings constructed with concrete frames. Carbon accounting includes: emissions due to fossil fuel use in the production of building materials; the replacement of fossil fuels by biomass residues from logging, wood processing, construction and demolition; carbon stock changes in forests and buildings; and cement process reactions. The results show that wood-framed construction requires less energy, and emits less CO₂ to the atmosphere, than concrete-framed construction. The lifecycle emission difference between the wood- and concrete-framed buildings ranges from 30 to 130 kg C per m² of floor area. Hence, a net reduction of CO₂ emission can be obtained by increasing the proportion of wood-based building materials, relative to concrete materials. The benefits would be greatest if the biomass residues resulting from the production of the wood building materials were fully used in energy supply systems. The carbon mitigation efficiency, expressed in terms of biomass used per unit of reduced carbon emission, is considerably better if the wood is used to replace concrete building material than if the wood is used directly as biofuel.     

On-line optical determination of floc size of Fe(Ⅲ) coagulants

This study investigated the floc aggregation, average floc size, floc size variance and floc growth velocity when ferric chloride （FeCl3） and polyferric chloride （PFC） were used to treat the simulated water samples. The factors including coagulant dose, ionic strength and solution pH, which affect the floc aggregation, were studied. Experiments were carried out in a bench-scale reactor using photometric dispersion analyzer （ PDA）. Results showed that there were great differences between the floc aggregation of PFC and FeCl3. The average floc size and fioc growth velocity of PFC were much larger than those of FeCl3. Compared with FeCl3, PFC gave a better coagulation performance in wider range of pH, dosage and ionic strength. It was also found that the coagulation efficiency of PFC did not depend on average floc size but on floc growth velocity.     

戴明循环理论在规划环评工作程序中的应用初探

通过分析现阶段我国规划环评的现状和存在的问题,结合国内外规划环评及其工作程序的研究成果,提出使用戴明循环理论对现阶段的规划环评工作程序进行改进,使程序层次化、工作细分化,增强整个规划环评工作的可操作性,使规划环评工作落实到单位和人,明确责任,减少部门间冲突.戴明循环理论的引入,提高规划环评的评价效果和效率,为规划环评提供了一个有效科学的评价方法,有助于规划环评的顺利开展,使环境问题从源头上得到控制,适应建设和谐社会的需要.     

氨法烟气脱硫脱硝的技术特征

氨法烟气脱硫脱硝具有显著的技术优势:脱硫效率高,脱硫脱硝一举两得,不耗费热量不产生废渣,脱硫剂利用充分用量小,不损害设备有节能功效。脱硫剂利用率可达90%以上,脱硫效率可达90%以上、脱硝效率可达80%以上;脱硫剂用量是钙法工艺的十到二十分之一;副产物为可以直接利用的化学肥料,而非难于处置的废渣。     

采用钙钛矿型催化剂(La0.8K0.2Cu0.05Mn0.95O3)同时催化去除NOx和碳烟的研究

将钙钛矿型催化剂与碳烟均匀混合后置于固定床连续流动反应体系中,利用程序升温反应技术,在模拟柴油机尾气的情况下对同时催化去除氮氧化物(NOx)和碳烟的反应进行了实验研究.通过改变含Cu原料的用量,得到不同Cu取代量的催化剂La0.8K0.2CuxMn1-xO3,性能评价结果表明,La0.8K0.2Cu0.05Mn0.95O3催化剂的综合性能较好,碳烟的起燃温度及NO向N2的最大转化率分别为280℃和58.0%.采用该催化剂,进一步考察了进气中NO浓度、O2浓度、进气总流量及催化剂与碳烟的接触状况对反应的影响.研究结果表明,进气中NO浓度、O2浓度、气体总流量和催化剂与碳烟之间的接触状况对NO的去除率的影响比较明显,而对碳烟起燃温度的影响较小.O2浓度从5%变为7.5%时,碳烟的起燃温度及最大NO转化率分别从280℃和53.8%变为270℃和96.7%.碳烟与催化剂松散接触时,碳烟的起燃温度及最大NO转化率分别为290℃和48.4%,紧密接触时分别为275℃和70.4%.而进气中NO浓度、气体总流量的变化对碳烟的燃烧基本上没有影响,虽然NO的转化率有明显变化,但生成的N2总量基本不变.     

Ni2+对2-氯酚厌氧降解系统的影响

针对重金属对难降解有毒有机物厌氧降解的影响问题,采用间歇试验法研究Ni2 对2-氯酚(2-CP)厌氧降解系统的影响规律.结果表明,当ρ(Ni2 )＜5 mg/L时,Ni2 对2-CP厌氧降解表现出轻度促进,当ρ(Ni2 )为5～500 mg/L,Ni2 以抑制作用为主,抑制作用随ρ(Ni2 )的增加而增强.Ni2 对原基质及关键中间产物苯酚和苯甲酸的抑制程度表现为:苯酚＞苯甲酸＞2-CP;ρ(Ni2 )低时的驯化能有效提高厌氧污泥对Ni2 毒性的耐受性能,300 mg/L Ni2 对2-CP降解的抑制从驯化前的65%降至驯化后的21%.Ni2 对2-CP厌氧降解的抑制作用与污泥中Ni的截留量之间存在正相关关系.抑制浓度CIP值和方程αC=[1-(I/I*)m]/[1 (I/I*)n)]能较好地表征厌氧生物处理过程受抑制程度.