铬渣中铬的浸出行为

采用BCR法连续浸提研究铬渣中铬的存在形态,结果表明:铬渣中总铬和六价铬主要以残渣态和可氧化态形式存在;通过铬渣动态连续浸提实验与静态浸提实验研究了浸提剂和活性炭对铬渣中铬浸出行为的影响,研究发现p H值为3.1的醋酸浸提剂浸出液中铬浓度最低,且添加活性炭后的静态浸出液中铬的浓度有不同程度降低。     

Simultaneous photocatalytic treatment of Cr(VI), Ni(II) and SDBS in aqueous solutions: Evaluation of removal efficiency and energy consumption

Simultaneous photocatalytic reduction of poisonous Cr(VI) and Ni(II) ions, coupled with photocatalytic oxidation of sodium dodecyl benzene sulfonate (SDBS) were studied with a trace amount of commercial titania nanoparticles and by means of a direct-photo-irradiation reactor. The co-presence of metal ions and SDBS causes metal ions reduction as well as SDBS oxidation to enhance and energy efficiency to improve. XRD, XPS and FTIR analysis were used to characterize TiO₂ particles before and after usage with the aim of evaluating the mechanism of reactions. The effect of major operating parameters, pH and temperature, was investigated. Under conditions of [Cr(VI)]₀ = [Ni(II)]₀ = 5 mg/L, [SDBS]₀ = 10 mg/L, [TiO₂] = 40 mg/L, pH 6 and T = 35 °C; the removal efficiencies of 55.4%, 71.2% and 57.2% were obtained, respectively, for Cr(VI) and Ni(II) reduction, as well as for SDBS oxidation, after 110 min operation. The relevant kinetic model jointed with the Arrhenius equation was introduced. Pseudo-first-order reactions are relevant. Energy consumption (electrical and thermal) evaluations revealed that operations at higher temperatures provide significant cost reduction. Meantime, a criterion was proposed for a consistent assessment of this kind of processes.     

运行参数对水蚯蚓生物吸持六价铬性能影响研究

水蚯蚓能通过摄食剩余污泥而使污泥减量,但剩余污泥中常含有各种重金属污染物.本文以颤蚓科蠕虫(Tubificidae)为研究对象,以六价铬为典型重金属污染物,考察运行工艺参数:初始铬浓度、p H、水蚯蚓投加量和温度对水蚯蚓吸持六价铬的影响.实验结果表明,在研究浓度范围内(0.1~8.0 mg·L-1),水蚯蚓对六价铬的吸持速率随铬浓度的增大而加快,单位质量吸持量从14.4 mg·kg-1(以干重计,下同)增加到312.7 mg·kg-1,但六价铬的吸持率却随Cr6+初始浓度的增加而降低;p H从6.0增加到8.0,水蚯蚓对六价铬的吸持速率随p H的上升而提高,吸持率和单位质量吸持量先明显增强,p H达到7.5后逐渐趋于平衡,即吸持最佳p H为7.5;水蚯蚓投加量从1.0 g(以湿重计,下同)增加到5.0 g时,吸持速率及吸持率均上升,但单位质量吸持量却随着水蚯蚓投加量的增加而减少;当温度在10~20℃范围内时,水蚯蚓对六价铬的吸持速率相对较慢,到25℃时,吸持速率明显加快,吸持率和单位质量水蚯蚓的吸持量的变化趋势与吸持速率的变化相一致,但当温度达到30℃,水蚯蚓会大量死亡,综合考虑,处理系统最佳温度宜控制在25℃.     

Removal of Cr(VI) from Cr-contaminated groundwater through electrochemical addition of Fe(II)

The conventional chemical reduction-precipitation technique in the removal of Cr(VI) from contaminated groundwater involves a two-step process whereby Cr(VI) is first reduced to Cr(III) at an acidic pH by a reducing agent and in a subsequent step, Cr(III) is precipitated as insoluble hydroxide at an alkaline pH. In a variation of this method, Fe(II) is added electrochemically to the Cr(VI) containing water. From a pure iron electrode, Fe(2+) ions are released into the solution and bring forth the reduction of Cr(VI). At the cathode, H(2)O is reduced whereby the OH(-) ions entering the solution keep the pH of the solution in the alkaline range. This latter fact greatly facilitates simultaneous reduction of Cr(VI) to Cr(III) and co-precipitation of hydroxides of trivalent Cr and Fe. On the basis of a set of experimental data, it is shown that this process is both thermodynamically and kinetically efficient, meaning, with the electrochemical method, rapid and nearly complete removal of Cr(VI) from a groundwater source with both high and low levels of Cr-contamination can be achieved. These factors make the electrochemical process superior to the conventional chemical process in remediation of Cr-contaminated groundwater.     

毫米波近炸探测器超宽带电磁脉冲防护加固措施研究

目的 研究毫米波引信近炸探测器超宽带(Ultra-wideband,UWB)电磁脉冲防护加固措施,提高引信的电磁防护能力。方法 利用超宽带辐照试验平台,开展辐照试验,通过测试,确定受损探测器的损伤部位,明确辐照效应机理,并提出针对性加固措施。结果 超宽带电磁脉冲可使探测器出现死机或硬损伤的现象,受试探测器的效应场强阈值在50~80 kV/m。死机可在重启后恢复,而硬损伤为不可恢复现象。结论 毫米波引信近炸探测器对超宽带电磁脉冲较为敏感,锁相环回路是探测器的敏感部位。探测器暴露在辐照场下的射频电路和天线窗口是超宽带能量的主要耦合通道。采取改进元器件布局、更换器件和屏蔽线等加固措施后,探测器超宽带的防护能力有较大提升,证明了加固措施的有效性。     

The NICE-Whyco technologies partnership: saving energy, dollars, and the environment in the metal plating industry

In partnership with the US Department of Energy’s Office of Industrial Technology, Whyco Technologies, Inc., has developed an innovative perforated plating barrel used in the plating of metal parts. This new technology employs a thin-walled construction, differing from the traditional thick-wall design required to provide adequate structural integrity. The thicker walls lowered the efficiency of transferring plating solution into and out of the barrel and diminished the electrical current pushed through the holes and onto the parts being plated. By machining pockets out of the traditional thick-walled perforated structure, Whyco produced a ‘honeycomb’ of staggered cells, allowing for the greatest number of holes per open area while maintaining structural integrity. Hydrodynamic pumping occurs during barrel rotation to create greater solution transfer than in traditional barrels. The Whyco barrel has higher current density plating, which leads to faster plating cycles, reduced bath concentration, and better plating of difficult chemistries such as in alloys. This new technology has helped the company reduce energy use by 16%, eliminate more than 480 tons/year of solid waste, and reduce wastewater by more than 17 000 gallons/day. The resulting cost savings total more than $500 000 annually. The company has manufactured and sold more than 275 of these barrels to other electroplating companies that are reporting up to a 40% increase in plating productivity and similar energy and environmental impacts.     

污染场地修复技术筛选方法及应用

污染场地修复技术的筛选是场地监管中的重要环节,修复技术的适用性直接影响场地修复效果及费用.确定最适修复技术时需综合考虑污染物特征、场地条件、修复费用及时间等多种因素,目前我国在污染场地修复技术筛选时多依赖专家赋值评分,在决策方法的推广上受到限制.本文在国内外相关研究基础上,考虑我国污染场地监管需求,提出土壤修复技术初筛及详细评价方法,并建立了修复技术筛选指标体系.为解决在各指标赋值及评价过程中存在的模糊性问题,利用可拓理论进行修复技术等级划分.以我国某铬渣污染场地为例,开展了土壤修复技术筛选研究,提出了最适的修复技术,研究成果可为我国污染场地监管工作提供科技支撑.     

高指数晶面TiO2对铬的吸附及光催化去除

由工业生产引起的铬污染是环境领域面临的一大挑战.二氧化钛(TiO_2)材料因其吸附催化的双重作用在铬的去除方面具有潜在应用前景.利用溶剂热法合成高指数晶面TiO_2{201},对其进行SEM、TEM、XRD及XPS表征,并用于Cr(Ⅲ/Ⅵ)的吸附及Cr(Ⅵ)的光催化还原,以达到从水体中去除铬的目的.所合成的TiO_2{201}为锐钛矿相,呈蒲公英状的层级结构. Langmuir吸附等温线结果表明,TiO_2{201}对Cr(Ⅲ)和Cr(Ⅵ)的最大吸附量分别为22. 7 mg·g-1和13. 2 mg·g-1,Freundlich模型拟合结果表明TiO_2{201}对Cr(Ⅲ)和Cr(Ⅵ)的吸附均易于进行,其1/n均小于0. 5.在紫外光照条件下,TiO_2{201}作为光催化剂可将毒性较强且吸附去除效果较差的Cr(Ⅵ)还原成Cr(Ⅲ),并以Cr(OH)3及Cr2O3的形式沉淀在TiO_2表面,XPS表征结果进一步证实了表面沉淀的存在.为探明TiO_2{201}光催化还原Cr(Ⅵ)的机制,分别研究光生空穴淬灭剂(EDTA-2Na)和光生电子淬灭剂(KBr O3)对Cr(Ⅵ)还原效率的影响,证明Cr(Ⅵ)的还原是由光生电子引起.     

电弧离子镀HY11涂层的1200℃高温氧化行为研究

目的研究真空电弧镀方法制备的超高温金属涂层HY11在1200℃下的高温氧化行为。方法用真空电弧镀技术(AIP)在单晶镍基高温合金DD6上制备超高温金属涂层HY11,采用HB 5258循环氧化方法进行1200℃循环氧化试验,通过试验过程中试样质量变化评价涂层氧化寿命。通过扫描电镜(SEM)分析氧化后的试样显微形貌,用X-射线衍射仪分析涂层材料的相结构,通过氧化速率对涂层材料抗氧化性能进行表征。结果采用单靶真空电弧镀技术制备的HY11涂层,经过1050℃真空条件下扩散2h,涂层厚度为50～60?m,扩散区厚度为10～15μm,涂层微观组织均匀致密,涂层合金界面清晰平整。DD6合金的1200℃循环氧化寿命仅仅为4 h,HY11涂层在1200℃的循环氧化寿命近300 h。沉积态涂层HY11相结构主要以Al_2O_3和Ni3Al为主。氧化后涂层材料表面形成的氧化膜以Al_2O_3为主。结论 HY11涂层在1200℃的循环氧化寿命为298 h,极大地提高了DD6合金在1200℃的循环氧化寿命。     

腐殖酸对砂质土壤吸附Cr(VI)的影响

利用系列摇瓶振荡实验,研究了在砂质土壤介质中腐殖酸(HA)对Cr(VI)还原作用及增强土壤表面对其吸附的影响.通过改变反应接触时间、pH值、HA投加量等条件,确定了最佳吸附反应条件.结果表明:砂质土壤中存在HA时,可使Cr(VI)还原为毒性较小的Cr(Ⅲ),明显增强土壤对可溶态Cr离子的吸附能力,比同等条件下无HA的土壤吸附量增大1倍以上.一般整个反应过程约8 h即可达到稳定.pH值对Cr的还原和吸附有很大的影响,酸性条件下的吸附量比碱性条件可增大1倍,最佳pH值为2～4;当pH＞5时吸附能力急剧下降,pH=10时吸附去除量降为20%.有HA存在时砂质土壤土对Cr(VI)的吸附反应为一级动力学反应,K298=0.033 5 min-1,砂土对CrO2-4的等温吸附曲线较好地满足Langmuir公式.