Ni-W合金电镀有机废水处理新方法

利用自行研制的氧化絮凝复合床新方法处理了Ni W合金电镀有机废水,并对原有电镀废水处理工艺进行了分流处理改造。水处理工程运行结果表明 :该工艺技术经济实用、处理效果好、稳定性高,处理后的水质完全符合排放标准     

电气线路火险隐患与运行设备故障隐患在线热诊断系统

研究根据电气线路和设备表面温度场的变化,通过建立数学模型和数据库,对电气线路和设备的故障隐患者在线诊断。集红外热象测试技术,传热学,电工学和计算机技术为一体,具有非接触,在线诊断,准确给出故障位置等特点,能精确发现温度场异常点,确定隐患等级,推测隐患的发展程度。     

电气火灾残留物的SEM分析方法研究

通过分析电气火灾的形成原因,总结出该类型火灾的残留物种类。然后利用电焊机和电阻炉等设备分别制备出铜铝导线的一、二次短路熔痕和火烧熔痕,电热丝的通电过热和火烧熔痕,并运用了目前一种新式有效的显微结构分析工具——扫描电子显微镜,对以上样品的表面进行微观形貌的观察、比较与分析。通过分析讨论,可以发现电气火灾残留物在火灾前后其表面的微观形貌特征存在明显不同。根据这些特征能够很轻易的鉴别出电气设备在火灾发生前的使用状态,从而推断出火灾是否由该电气设备引发而起。此项结论能够为从事火灾调查的人员对电气火灾原因的准确认定提供可靠依据,也能够为扫描电子显微镜技术的应用领域进行拓宽提供一些帮助。     

热带海洋环境中5083铝合金腐蚀行为研究

目的 研究某岛礁不同海洋区带环境中5083铝合金的腐蚀规律。方法 在某岛礁进行海洋多区带腐蚀试验,利用表面微观形貌观测、腐蚀产物分析、质量损失测试及点蚀深度测量等手段,对比分析铝合金在不同海洋区带中的腐蚀形貌、腐蚀速率和点蚀深度。结果 5083铝合金在某岛礁海洋全浸区带环境中的腐蚀速率最大,大气区带中的腐蚀速率最小,在潮差区带的腐蚀速率介于二者之间。试样在海洋不同区带主要发生局部腐蚀,大气区试样的最大点蚀深度最大,而潮差区试样的最大点蚀深度最小。在不同海洋区带,铝合金腐蚀产物和附着物的混合物中均含有钙元素,大气区钙元素含量远低于潮差区和全浸区,潮差区和全浸区铝合金表面的腐蚀产物和附着物混合物中主要含有CaCO₃、CaSiO₃和Al₂O₃。结论 不同海洋区带环境中,5083铝合金的腐蚀速率差别较大,潮差区和全浸区材料表面附着大量污损生物和矿物质。     

新型锌／铜／铝类水滑石的合成及对模拟印染废水吸附性能的研究

采用低饱和共沉淀法制得锌／铜／铝类水滑石化合物（Zn5CuAl2（OH）16CO3·xH2O）,在450℃焙烧得焙烧物,通过XRD ,FT－IR ,SEM和TG－DSC等手段对样品的结构、形貌和热稳定性进行了分析。将其焙烧物用于吸附模拟印染废水中的阴离子染料活性艳橙,结果表明,pH值在2～9,经吸附90 min ,其对印染废水的吸附性能最佳,染料去除率达96％以上。     

Validation of the UN test method N.5

Many substances react with water in such a way that flammable gases are formed. For transport issues this reaction may possess a considerable hazard especially if the cargo is wetted by rain or by water from other sources. In the UN Recommendations on the Transport of Dangerous Goods these kinds of problems are addressed. The UN test N.5 “Test method for substances which in contact with water emit flammable gases” corresponds to this hazard. Classification according to the test method is done by measurement of the gas evolution rate of the flammable gas by any suitable procedure. At BAM a gravimetric approach is used to measure the gas evolution rate. In this paper we present the evaluation of the apparatus by means of an absolute calibration routine utilizing a reaction where a known amount of gas is produced as well as the evaluation of important parameters influencing the gas evolution rate using different substances. It can be shown that the apparatus is capable of measuring absolute gas volumes as low as 6 mL with an acceptable error of about 17% as determined from the reaction of Mg with demineralized water.     

Corrosion behavior of steels for CO2 injection

The process chain for Carbon Capture and Sequestration (CCS) includes tubing for injection of CO₂ into saline aquifers. The compressed CO₂ is likely to contain specific impurities; small concentrations of SO₂ and NO₂ in combination with oxygen and humidity are most harmful. In addition, CO₂ saturated brine is supposed to rise in the well when the injection process is interrupted. The material selection has to ensure that neither CO₂ nor brine or a combination of both will leak out of the inner tubing. In this comprehensive paper the investigated materials range from low-alloy steels and 13% Cr steels up to high-alloy materials. Electrochemical tests as well as long term exposure tests were performed in CO₂, in brine and combination of both; pressure was up to 100 bar, temperature up to 60 °C. Whereas the CO₂ stream itself can be handled using low alloy steels, combinations of CO₂ and brine require more resistant materials to control the strong tendency to pitting corrosion. The corrosion behavior of heat-treated steels depends on factors such as microstructure and carbon content. For different sections of the injection tube, appropriate materials should be used to guarantee safety and consider cost effectiveness.     

The Al Gore effect: An Inconvenient Truth and voluntary carbon offsets

This paper examines the relationship between climate change awareness and household behavior by testing whether Al Gore's documentary An Inconvenient Truth caused an increase in the purchase of voluntary carbon offsets. I find that in the two months following the film's release, zip codes within a 10-mile radius of a zip code where the film was shown experienced a 50 percent relative increase in the purchase of voluntary carbon offsets. During other times, offset purchasing patterns for zip codes inside the 10-mile radius were similar to the patterns of zip codes outside the 10-mile radius. There is, however, little evidence that individuals who purchased an offset due to the film purchased them again a year later.     

铜导线短路熔痕的SEM/EDS分析

在电气线路火灾原因的调查中,为更好地区分铜导线一次短路与二次短路的熔痕特征,用扫描电子显微镜(SEM)和X-射线能谱仪(EDS)对2种熔痕的形貌和相应的元素成分进行了试验研究。结果表明:铜导线一次短路与二次短路熔痕的表观形貌特征和元素成分具有明显的不同,二者的区别主要表现在熔痕表面所含的气孔、元素种类及导线本体与熔痕之间的过渡区方面,一次短路熔痕表面气孔多,元素种类少,导线与熔痕之间有明显界限,二次短路熔痕则相反。该研究结果可以区分短路熔痕形成的环境气氛,以此判断导线短路熔痕类型,为电气线路火灾原因的调查提供科学依据。     

Al2O3/Ni-P-SiC复合涂层组织与性能的研究

目的 采用化学复合镀技术对微弧氧化进行封孔,进而得到抗烧蚀性能优良的Al2O3/Ni-P-SiC复合涂层。方法 通过采用扫描电镜(SEM)、光学金相显微镜(OM)、显微硬度仪(Microhardness Tester)、X射线衍射仪(XRD)、氧–乙炔烧蚀试验(Oxy-Acetylene Ablation Test)等方法,对复合涂层的表面形貌、截面形貌、厚度、显微硬度、物相和抗烧蚀性能等进行分析。结果 陶瓷层原始表面完全被化学镀层覆盖,所制得的复合涂层厚度均匀,化学镀层与陶瓷层紧密嵌合。镀液中的SiC浓度对镀覆的速度、镀层中SiC粒子的共沉积量有着较大的影响。当粒子质量浓度为16~20 g/L时,颗粒的共沉积量较大。化学复合镀60 min可以得到厚度20 μm左右的Ni-P-SiC镀层,SiC颗粒分布均匀。当镀液中SiC质量浓度为16 g/L时,镀层具有最高的硬度。对比未处理、仅微弧氧化和Al2O3/Ni-P-SiC复合涂层试样,Al2O3/Ni-P-SiC复合涂层试样具有最佳的抗烧蚀性能。结论 Al2O3/Ni-P-SiC复合涂层均匀、致密,具有良好的抗烧蚀。