城市餐厨垃圾前处理的工艺优化

为提高餐厨垃圾资源化,利用自动化分选设备组合处理餐厨垃圾,考察餐厨垃圾快速减量化和资源化的可行性,对自动化分选前后餐厨垃圾成分进行分析,发现分选前其总量为243.05 t·d-1,TS为12.69%,VS为93.26%,分选后总量为242.00 t·d-1,TS为10.97%,VS为91.93%,其有机物含量稳定,利于厌氧发酵处理的工艺控制;对分选后餐厨垃圾进行厌氧发酵处理,考察其pH和NH4+-N变化,发现反应初期pH值出现弱酸性,NH4+-N浓度较低;随着反应进行,pH稳定在7.6~7.8,NH4+-N浓度约为1 200 mg·L-1左右。最后对厌氧发酵产气量进行考察发现,反应前期受到pH、NH4+-N以及温度等反应条件影响,产气量和甲烷含量较低;随着实验趋于稳定,产气量为22 000 m3·d-1左右,甲烷含量范围在65%~72%。结果表明,使用新型餐厨垃圾预处理设备,其分选效率较高,能提高后续厌氧发酵产气量和甲烷含量,较大程度实现餐厨垃圾资源化。     

观赏植物与驯化污泥联合修复垃圾渗滤液污染土壤

垃圾填埋场渗滤液污染土壤具有重金属-有机物复合污染的特性。研究了观赏植物广东万年青、白掌、孔雀竹芋和经垃圾渗滤液驯化的污泥对该污染土壤的修复效果,结果表明：采用单一植物修复时,广东万年青较白掌和孔雀竹芋对土壤污染物具有更强耐性,能在污染土壤中生长良好,对重金属Cd和Pb的富集能力也更强;驯化污泥能明显提高污染土壤中有机污染物的降解率,并使重金属Cd和Pb稳定态比例分别提高了34.7%和36.6%,降低了重金属的生物有效性。当采用广东万年青和驯化污泥联合修复时,污泥能促进植物的生长,且当污泥添加量为480 mg·kg-1时,联合修复对土壤中Cd、Pb及有机污染物的去除率分别较不加污泥的对照提高了51.7%、25.5%和40.2%。     

小尺度农田土壤Pb、Zn和Cd空间分布及污染评价——以云南沘比江沿岸某农田为例

以沘江沿岸面积为96 000 m2的整片农田作为研究对象,采集144个表层土壤样本,利用ICP-MS测定土壤中Pb、Zn和Cd的含量,使用地统计学方法分析Pb、Zn和Cd的空间分布,采用污染负荷指数评价土壤Pb、Zn和Cd污染程度,并对污染来源进行解析。结果表明研究区域农田土壤中Pb、Zn和Cd含量均超过当地土壤背景值,出现了污染富积。根据国家土壤环境质量标准,Pb未超标,Zn超标率为98.6%,Cd超标率为100%。普通克里金空间插值分布图显示,Pb、Zn和Cd高含量区域均沿着省道227和靠近居民区分布,而临近沘江的区域Pb、Zn和Cd含量相对较低,其中Pb、Zn含量变化基本呈现由省道227向沘江方向递减规律。Pb、Zn和Cd之间具有较好的相关性,三者同源概率较大。对Pb、Zn和Cd的污染评价表明,研究区域农田土壤57.78%为中度污染,42.22%为重度污染。从污染负荷指数法（PLI）空间插值图可见,重度污染区域位于省道227沿线与居民区东侧区域,其余区域为中度污染。本研究结果说明,小尺度空间分析方法用于农田土壤污染状况的分析,能有效预测重金属空间分布情况,在土地紧缺的情况下,该方法能有效指导对农田的不同区域进行选择使用和精准管理。     

稳定剂协同水泥固化/稳定化重金属污染土壤的工程特性

采用稳定剂（SR）协同水泥（PC）固化/稳定化重金属污染土壤,以Pb、Zn浸出毒性和药剂吨处理成本为综合指标确定PC和SR的最优配比,并对固化土体进行无侧限抗压强度、不固结不排水三轴压缩实验和柔性壁渗透实验,探讨固化土体强度以及渗透特性。结果表明,最优配比为SR掺量 2.5%,PC掺量8%;最优配比下固化土体中重金属铅锌的浸出浓度分别降低97.5%和74.5%,均低于固体危险废物浸出标准值。其养护28 d无侧限抗压强度达到1 080 kPa,比未固化土体对应值高9.6倍;随着PC掺量增加,固化体的有效黏聚力及有效内摩擦角均不断增大,其中最优配比固化土体有效黏聚力达到216.9 kPa,有效内摩擦角为34.8°。加入稳定剂SR使固化体渗透系数增大,但随着PC掺量增加,渗透系数急剧降低。其中最优配比固化土体渗透系数相对未固化复合污染土体降低一个数量级至10-6cm·s-1,可有效增强土体的防渗阻隔能力,提高稳定化土壤的安全利用率。     

诱导结晶法同时去除铜、锌离子

考察投药量、水力负荷、停留时间等因素,对诱导结晶反应器去除Cu2+、Zn2+效果的影响,确定最佳运行参数为：水力负荷40 m3·（m2·h）-1,结晶药剂投药量2：1,停留时间90 min。在最佳运行参数下,结晶反应器处理含铜20 mg·L-1,含锌10 mg·L-1、pH为5.5~6.0的混合重金属废水。反应器连续运行40 d,出水中铜离子和锌离子平均浓度分别为1.31 mg·L-1和4.57 mg·L-1,铜离子和锌离子平均去除率分别是93.4%和51.3%。诱晶载体粒径由0.568 mm长至0.617 mm,平均生长速度为0.001 23 mm·d-1。研究表明,该诱导结晶工艺可以用作同时去除废水中的Cu2+、Zn2+。     

EuroBionet: a pan-European biomonitoring network for urban air quality assessment

EuroBionet, the 'European Network for the Assessment of Air Quality by the Use of Bioindicator Plants', is an EU-funded cooperative project currently consisting of public authorities and scientific institutes from 12 cities in 8 countries. In 2000, the bioindicator plants tobacco (Nicotiana tabacum Bel W3), poplar (Populus nigra 'Brandaris'), spiderwort (Tradescantia sp. clone 4430), Italian rye grass (Lolium multiflorum italicum) and curly kale (Brassica oleracea acephala) were exposed to ambient air at 90 monitoring sites according to standardised methods. Visible injuries and growth parameters were assessed and the accumulation of toxic substances in leaves determined. The exposure of tobacco resulted in a gradient with low levels of ozone-induced foliar injury in N and NW Europe, and medium to high values in the southern and central regions. The results of heavy metal and sulphur analyses in rye grass samples generally showed low to very low sulphur and low to medium heavy metal concentrations in leaves. In some cities, however, local hot spots of heavy metal contamination were detected. Analyses of the PAH contents in curly kale leaves gave low to medium values, with locally elevated levels at traffic-exposed sites.     

城市污水污泥固结体重金属浸出毒性及路用性能研究

城市污水污泥的重金属离子Pb、Zn超过国家固体废弃物排放最高允许值,属于危险废物。污水污泥的最佳出路是无害化处理,资源化利用,产业化发展。研究了以上海市污水污泥为原料,加入一定比例的固化剂和矿物掺合料使之固结,经养护满足路用强度性能,测试其固结体重金属离子浸出质量浓度亦满足国家固体废弃物排放标准,即污泥中的重金属离子得到有效的束缚和稳定固化,既解决了环境问题,又为污泥产业化发展开辟了新的途径。     

Seasonal Fluctuation in Heavy Metal Pollution in Iran´s Siahroud River - A Preliminary Study (7 pp)

Background The management of its available water resources has become a key issue for Iran. During the last few decades, the water quality of Siahroud River in the coastal plain of the Caspian Sea in Gilan Province in Northern Iran has significantly degraded. The scarcity of water has been compounded by rapid population growth and increasing pollution from fertilizers, pesticides, and municipal and industrial wastes. One of the sources of this degradation is the movement of heavy metals from the river's watershed into the various water systems supported by the river, including the water system for Rasht City. Methods To study the magnitude of heavy metal pollution in the Siahroud River, seven heavy metals including Zn, Cu, Pb, Cd, Mn, Fe, and Ni were measured in duplicate from replicated water samples collected over five consecutive seasons and analyzed by Atomic Absorption Spectrometry. In situ measurements of pH were taken with the samples and total organic carbon (TOC) was analyzed by IR gas measurement. Results The results demonstrated that four of the seven heavy metals including Pb, Fe, Cd, and Mn exceeded permissible safe levels as established by the United States Environmental Protection Agency. Multivariate factor analysis suggested that industrial land-use was the main contributing factor for the high levels of Fe and Mn in the Siahroud River, whereas, Cd was principly from agricultural activities in the watershed. The data also suggested that pH and TOC had an important role in the behaviour of Pb and Mn, and that the elevated levels of these two heavy metals in Siahroud River was the consequence of other anthropogenic sources. Only negligible levels of Zn, Cu and Ni were detected. Finally, all the sampling stations were subjected to cluster analysis. The results indicated that three different zones could be distinguished according to the levels of pollution. In addition, it was shown that the urban areas did not have a significant impact on the heavy metal pollution in the river. This observation stems from the fact that the data from the sampling stations before and after Rasht City were not significantly different. Recommendation . Preventive measures need to be undertaken in the land-use systems and watersheds of the Siahroud River to reduce the pollution levels of Pb, Cd, Mn and Fe.     

复合菌系RXS中木质纤维素降解酶类分析

复合菌系RXS能分泌多种木质纤维素降解酶,为探究这些酶在木薯渣降解中的作用,对RXS的培养时间、酶作用的温度和pH值,以及添加金属离子对酶活性和降解效果的影响进行了研究。结果表明,在培养48 h后,木聚糖酶(Xylanase)、滤纸酶(FPAase)和内切葡聚糖酶(CMCase)酶活性均达到最大值(分别为56.02 U/m L、3.14U/m L和6.78 U/m L),pH=6.0(FPAase和Xylanase的最适pH值)、温度为55℃(FPAase和CMCase酶活性最高)条件下,RXS酶液处理可使木薯渣的失重率达到18.78%,纤维素和半纤维素质量分数分别由31.46%和20.19%下降到22.12%和12.23%。添加Cu~(2+)有效地抑制了酶液中FPAase和Xylanase的酶活性,木薯渣几乎不降解,纤维素和半纤维素组分质量分数基本不发生变化;分别添加Co~(2+)和Zn~(2+)时,对3种酶均有一定程度的抑制,木薯渣失重率仅为3.29%和4.70%;分别添加Fe~(2+)、Mg~(2+)时,FPAase酶活性被抑制,Xylanase与CMCase共同降解底物,木薯渣失重率分别达12.77%和15.81%,纤维素和半纤维素质量分数明显降低。研究表明,Xylanase与CMCase是复合菌系中降解木薯渣的关键酶,其协同作用可使木薯渣有效降解。     

电镀污泥脱水稳定剂制备及应用研究

针对电镀污泥脱水过程中金属离子大量溶出带来的处理难题,以四甲基乙二胺、二硫化碳为主要原料,以氢氧化钾为引发剂,采用聚合法制备了一种脱水稳定剂,并考察了稳定剂投加量、污泥pH值、反应温度和反应时间对电镀污泥离心脱水时重金属溶出的影响。结果表明,在稳定剂投加量(稳定剂与污泥的质量比)为1%、反应温度为20℃、pH=1、反应时间为30 min、转速为3 000 r/min条件下对含Ni(Ⅱ)电镀污泥离心脱水后,Ni(Ⅱ)脱水稳定率达96.88%,且脱水稳定剂对混合电镀污泥中Ni(Ⅱ)、Cu(Ⅱ)的选择性大于Zn(Ⅱ)。脱水稳定剂的脱水稳定机理是其中的二硫代氨基甲酸盐与重金属离子M(Ⅱ)(Ni(Ⅱ)、Cu(Ⅱ)、Zn(Ⅱ)等)形成配位键,从而形成稳定的交联网状结构,达到化学稳定,实现了离心脱水极少重金属离子溶出(即脱水稳定)的效果。所合成的脱水稳定剂可广泛用于含镍、铜、锌等金属离子的电镀污泥脱水处理。