几种粘土矿物对Pb~(2+)的吸附作用及其主要影响因素的探讨

对土壤中常见的三种粘土矿物对Pb2+的吸附作用及其主要影响因素进行了探讨。结果表明，三种粘土矿物对Pb2+的吸附能力顺序为：蒙脱石＞伊利石＞高岭石。蒙脱石对Pb2+的吸附受pH的强烈影响，pH高有利于对Pb2+的吸附。与蒙脱石形成复合体形式的有机化合物的存在不利于蒙脱石对Pb2+的吸附。     

Fenton氧化法预处理垃圾渗滤液试验研究

采用Fenton氧化法处理长沙市黑糜峰垃圾填埋场垃圾渗滤液原液,考察了影响COD去除率的各种因素,包括初始pH值、FeSO4·7H2O投加量、双氧水投加量、反应时间及投加方式等,试验结果表明:在初始pH值为3、FeSO4·7H2O投加量为0.5%、双氧水投加量为18 mL/L、反应时间为100 min、投加方式为3次投加的条件下,可使垃圾渗滤液原液的COD去除率达40%左右,并提高了生化比,为后续生物处理改善了条件.     

氮氟掺杂二氧化钛(N,F-TiO2)的制备及可见光催化活性的研究

以氨水为氮源,氢氟酸为氟源,采用溶胶-凝胶法制备了氮氟掺杂二氧化钛(N,F-TiO2)光催化剂,并通过X-射线衍射(XRD)和扫描电镜(SEM)技术对其晶型和形态进行表征.最后以酸性红B为模型污染物,探讨了N和F加入量、焙烧温度、焙烧时间、照射时间、催化剂用量、溶液初始浓度和照射功率等因素对N,F-TiO2可见光催化活性的影响.结果表明,制备的N,F-TiO2以锐钛型为主,N和F的掺杂对TiO2的晶相没有明显改变,但可以扩大TiO2的可见光响应范围.当N和F的加入量均为2.0%,且在500℃下焙烧40 min时,得到的N,F-TiO2的可见光催化活性明显高于单N或单F掺杂的TiO2(N-TiO2或F-TiO2).对于50 mL浓度为10.0 mg·L-1的酸性红B溶液,当催化剂加入量为1.5 g·L-1,128W光照3.0 h,溶液pH=5.6时,去除率为85.40%.适当延长光照时间至4.0 h,降解率几乎可达100%.另外,研究还证明了N,F-TiO2催化可见光降解过程中有.OH自由基生成.     

OMS-2负载Pt催化剂的制备及其催化氧化性能研究

采用前掺杂法、沉积-沉淀法和浸渍法制备了氧化锰八面体分子筛(OMS-2)负载Pt催化剂(Pt/OMS-2),对所制催化剂进行了结构和织构表征。并研究了不同制备方法和沉积-沉淀法中不同制备(Pt负载量和溶液的pH值)对Pt/OMS-2催化氧化CO性能的影响。结果表明,沉积-沉淀法制备的Pt/OMS-2-DP催化剂活性最好(T100=100℃)。这与Pt/OMS-2-DP催化剂中Pt颗粒大小及OMS-2载体与Pt之间存在强相互作用有关。Pt负载量明显影响Pt/OMS-2-DP催化剂的催化活性,3Pt/OMS-2-DP催化剂(Pt=3.0 wt%)催化活性最高,这是由于适当Pt负载量,Pt颗粒较小,并与载体OMS-2的相互作用较强,能较好地活化OMS-2晶格氧。pH值对Pt/OMS-2-DP催化剂催化性能影响较大,这与OMS-2的等电点和Pt在不同溶液中存在不同Pt配位体形式有关。     

2,2′-二硝基联苄生产废水的处理研究

对十六烷基三甲基溴化铵改性凹凸棒土、凹凸棒土负载TiO2采用XRD、FTIR以及TG等手段进行了分析和表征,对比了改性凹凸棒土、活性炭、大孔树脂等不同吸附剂和凹凸棒土负载TiO2对二硝基联苄生产废水的处理效果。结果表明:十六烷基三甲基溴化铵改性凹凸棒土的废水中污染物的去除率比凹凸棒土提高了2.5倍;凹凸棒土负载TiO2在波长λ=254 nm下光照0.5 h,对废水中污染物的去除率是凹凸棒土的2.0倍;投加量为3%活性炭在pH为2.0⁵.0时,对该类废水中污染物的去除率可达80%以上。     

Fe2O3 particles as superior catalysts for low temperature selective catalytic reduction of NO with NH3

Fe203 particle catalysts were experimentally studied in the low temperature selective catalytic reduction （SCR） of NO with NH3. The effects of reaction temperature, oxygen concentration, [NH3]/[NO] molar ratio and residence time on SCR activity were studied. It was found that Fe203 catalysts had high activity for the SCR of NO with NH3 in a broad temperature range of 150-270℃, and more than 95% NO conversion was obtained at 180℃ when the molar ratio [NH3]/[NO] = 1, the residence time was 0.48 seconds and 02 volume fraction was 3%. In addition, the effect of SO2 on SCR catalytic activity was also investigated at the temperature of 180℃. The results showed that deactivation of the Fe2O3 particles occurred due to the presence of SO2 and the NO conversion decreased from 99.2% to 58% in 240 min, since SO2 gradually decreased the catalytic activity of the catalysts. In addition, X-ray diffraction, Thermogravimetric analysis and Fourier transform infrared spectroscopy were used to characterize the fresh and deactivated Fe2O3 catalysts. The results showed that the deactivation caused by SO2 was due to the formation of metal sulfates and ammonium sulfates on the catalyst surface during the de-NO reaction, which could cause pore plugging and result in suppression of the catalytic activity.     

Characterizing the optimal operation of photocatalytic degradation of BDE-209 by nano-sized TiO2

Brominated flame retardants have been widely used in industry. There is a rapid growing public concern for their availabilities in the environment. Advanced oxidation process (AOP) is a promising and efficient technology which may be used to remove emerging chemicals such as brominated flame retardants. This project aims at investigating optimal operational conditions for the removal of BDE-209 using nano-scaled titanium(IV) oxide. The residual PBDE congeners after photocatalytical degradation of BDE-209 by TiO₂ were analysed by gas chromatography-mass spectrometry (GC-MS). It was found that the degradability of BDE-209 by TiO₂ was attributed to its photocatalytic activity but not the small size of the particles. The half-life of removing BDE-209 by TiO₂ was 3.05 days under visible light. Tetra- and penta-BDEs were the major degraded products of BDE-209. Optimum conditions for photocatalytical degradation of BDE-209 was found to be at pH 12 (93% ± 1%), 5, 10, 20 mg/L (93.0% ± 1.70%, 91.6% ± 3.21%, 91.9% ± 0.952%, respectively), respectively of humic acid and in the form of anatase/rutile TiO₂ (82% ± 3%). Hence, the efficiency of removing BDE-209 can be maximized while being cost effective at the said operating conditions.     

Investigation in the sorption mechanism and behavior of nano γ-Al2O3 for the removal of fluorine ions

研究了纳米γ-Al2O3吸附剂对氟离子的吸附行为,考查了吸附平衡时间、温度、溶液的pH等对吸附过程的影响.结果表明,在室温下,纳米γ-Al2O3对氟离子的吸附在3min基本达到平衡;在pH3～9范围内,吸附率达95%以上;吸附过程符合准二级反应动力学模型,其反应的表观活化能（Ea）为10.99kJ.mol-1;颗粒内扩散过程是吸附的主要控制步骤,而颗粒外扩散过程对吸附也有影响;吸附过程符合Langmuir、D-R等温模型,常温下,纳米γ-Al2O3对氟离子的平均吸附能为11.15kJ.mol-1.吸附反应的ΔGθ〈0,ΔHθ〉0,说明该吸附过程是自发的吸热反应.共存阴离子HCO3-和PO43-、阳离子Cu2＋对氟离子的吸附影响较大.纳米γ-Al2O3在动态和静态吸附实验中的除氟效果相近.     

电化学氧化法预处理超高盐榨菜腌制废水

鉴于超高盐榨菜腌制废水导电性良好,采用电化学氧化法进行预处理(阳极为Ti基RuO₂-TiO₂-IrO₂-SnO₂网状涂层形稳电极),考察初始pH、电流密度、电解时间和极板间距对COD_Cr和氨氮去除率的影响,并探讨该过程中有机物相对分子量的变化规律.结果表明,在电流密度156 mA/cm2、极板间距1.5 cm、初始pH 4.3~5.0、电解时间120 min时,COD_Cr和氨氮去除率较佳,分别为55.74%和99.77%.出水pH升至9.54,盐度由7.0%降至6.4%,大分子有机物转化为小分子有机物,对后续生物处理有利.      

纳米TiO_2纤维的制备及其光催化降解甲醛研究

以胶原纤维为模板制备纳米TiO2纤维用于光助催化降解甲醛气体,用扫描电镜(SEM)、X射线衍射(XRD)和N2吸附-脱附技术对纳米TiO2纤维进行了表征。结果表明,纳米TiO2纤维的比表面积为11.33 m2/g,晶型为锐钛矿型。在相同催化反应条件下纳米TiO2纤维对甲醛气体的催化降解率与商品纳米TiO(2Degussa P25)催化剂相当。纳米TiO2纤维的用量、甲醛气体初始浓度是影响催化效果的两个因素。当甲醛气体初始浓度为0.270 mg/m3,相对湿度为38%,气体流速0.1 L/min,纳米TiO2纤维用量为1.0 g时,甲醛的降解率达到96%。因此,纳米TiO2纤维可用于室内甲醛气体的催化降解。