膜过滤-气相色谱法测定涂料中的苯系物、环己酮和甲苯二异氰酸酯

采用膜过滤-气相色谱法测定涂料中的苯系物、环己酮和甲苯二异氰酸酯（TD I）。用7种规格的石英毛细管色谱柱对混合标准溶液和涂料试样进行了分析实验,实验结果表明,不同属性的涂料试样添加固定量的正十四烷作内标物,经膜过滤净化后,苯系物、环己酮和TD I可采用DB-1-3或DB-1-2色谱柱同时分离并测定。测试数据经多级校准曲线处理后涂料试样中苯系物、环己酮和TD I的加标回收率为98.6%～101.8%,各组分分析结果的变异系数均小于2.0%,检出限均小于1.50×10^-5g。     

阳离子型聚合物对低温低浊水的絮凝效果与形态学特性

采用微絮凝-深床直接过滤工艺,以西安市曲江水厂低温低浊水质为原水(水温低于10 ℃,初始浊度低于10NTU),投加阳离子型聚合物(简称CP)作主混凝剂或助凝剂,借助分形数学理论与图像分析技术,对滤料粒径、原水浊度、原水温度、药剂种类、聚合物分子量及投加量、混合强度等因素对处理效果的影响进行了研究,分析探讨了不同药剂处理低温低浊水的作用机理、絮凝形态学特征以及絮体结构的分形特性.结果表明,①当温度低于4 ℃、初始浊度小于4NTU时,不宜单独采用Al2(SO4)3或PAC作为絮凝剂;当温度为4～10 ℃、初始浊度小于10NTU时,如果只投加Al2(SO4)3或PAC作为絮凝剂,宜用细砂滤料过滤;低温低浊条件下,无机混凝剂形成的絮体粒径小、结构松散脆弱、有效质量密度低、沉速慢,但表征絮体分形特性的分维值较高.②CP作絮凝剂能显著改善低温低浊水的絮凝效果与过滤性能,但混合强度需增大,宜用粗砂滤料过滤;③单独用CP作絮凝剂时,宜投加分子量较低的弱阳性聚合物或投加低剂量较高分子量的强阳性聚合物;CP用作助凝剂时,能显著减少主混凝剂用量,但宜投加强阳性聚合物或增加弱阳性聚合物的剂量.④CP兼备电性中和与吸附架桥絮凝作用,能形成粒径较大、吸附性能与过滤性能良好的网状絮体构型,其有效质量密度高,产生的污泥量少,污泥沉降速度快,脱水效果好,但分维值低.⑤各种水处理药剂的处理效果为:Al2(SO4)3(或PAC) CP＞CP＞PAC＞Al2(SO4)3,这种差别由絮体的形态学特性与构型特征各异引起.     

固相萃取-UPLC-MS/MS法测定环境水体中多种抗生素

采用固相萃取-超高效液相色谱串联质谱法测定环境水样中25种磺胺类和喹诺酮类抗生素,通过优化试验条件,使方法在2.00μg/L～200μg/L范围内线性良好,方法检出限为1.01ng/L～2.85ng/L,7次测定结果的RSD为2.3%～8.0%。将该方法用于自来水和地表水测定,结果均为未检出,高、低质量浓度水平的加标回收率为61.2%～102%。     

HPLC-三重四级杆质谱法测定医疗废水中抗生素残留

采用固相萃取/高效液相色谱-三重四级杆质谱法同时测定医疗废水中的20种超痕量抗生素残留,通过优化试验条件,使方法在100μg/L～100μg/L范围内线性良好,方法检出限为024ng/L～122ng/L。空白水样和实际水样3个质量浓度水平的加标回收率分别为80.2%～108%和75.8%～114%,6次测定结果的RSD分别为2.4%～8.4%和1.7%～8.1%。将该方法用于测定重庆市2家三甲医院医疗废水中的超痕量抗生素残留,结果有11种抗生素检出,其余均为未检出。     

Sludge concentration dynamic distribution and its impact on the performance of UNITANK

UNITANK is a biological wastewater treatment process that combines the advantages of traditional activated sludge process and sequencing batch reactor, which is divided into Tank A, B and C. In this study, the sludge distribution and its impact on performance of UNITANK were carried out in Liede Wastewater Plant （WWTP） of Guangzhou, China. Results showed that there was a strong affiliation between Tank A and B of the system in sludge concentration distribution. The initial sludge concentration in Tank A could present the sludge distribution of the whole system. The sludge distribution was mainly influenced by hydraulic condition. Unsteady sludge distribution had an impact on variations of substrates in reactors, especially in decisive reactor, and this could lead to failure of system. Settler could partially remove substrates such as COD and NO3-N, but there was adventure of sludge deterioration. The rational initial sludge concentration in Tank A should be 4000-6000 mg/L MLSS.     

The impact of ISO 14001 on corporate environmental performance: a study of Swedish manufacturing firms

The debate concerning the environmental effectiveness of environmental management systems (EMS) based on ISO 14001 is still open and scholars have called for further studies that can explain the contrasting evidence in previous research. As a response, this study aims to contribute knowledge about the effects of ISO 14001-based EMS by presenting fact-based environmental data. The study focuses on changes in performance over a period of 12 years and includes both firms with an EMS (66 firms) and firms without one (50 firms). Consideration is given to the improvement efforts in the firms before EMS adoption making it possible to neutralize any selection effects where better environmental performance precedes ISO 14001 adoption. Analysis has been carried out using statistical methods for six different environmental areas. No statistically significant differences between certified and non-certified firms concerning the change in the rate of improvement could be found in any of the six areas. However, it can be suspected that EMS adoption has positive effects on energy use and waste production whereas the non-adopting firms seem to perform better concerning air emissions. These mixed results mirrors previous research, which is rather worrying considering the worldwide popularity of EMS based on ISO 14001 in industry.     

一种高压油管焊接质量评价方法

阐述了高压油管疲劳破坏的原理及危害,建立高压油管焊接质量评价力学模型,通过有限元分析技术对其许用位移输入进行计算,并结合应变测量技术,利用电动振动台,对高压油管焊接处的疲劳特性进行了试验验证。结果表明,此高压油管焊接质量评价方法是可行的,有限元分析技术和应变测量技术的结合使用,保证了试验的安全性和结果准确性,此外,利用电动振动台进行疲劳耐久试验,操作方便简单,成本相对较低,具有通用性。     

A real-time simulating non-isothermal mathematical model for the passive feed direct methanol fuel cell

In order to understand the complex transport phenomena in a passive direct methanol fuel cell (DMFC), a theoretical model is essential. The analytical model provides a computationally efficient framework with a clear physical meaning. For this, a non-isothermal, analytical model for the passive DMFC has been developed in this study. The model considers the coupled heat and mass transport along with electrochemical reactions. The model is successfully validated with the experimental data. The model accurately describes the various species transport phenomena including methanol crossover and water crossover, heat transport phenomena, and efficiencies related to the passive DMFC. It suggests that the maximum real efficiency can be achieved by running the cell at low methanol feed concentration and moderate current density. The model also accurately predicts the effect of various operating and geometrical parameters on the cell performance such as methanol feed concentration, surrounding temperature, and polymer electrolyte membrane thickness. The model predictions are in accordance with the findings of the other researchers. The model is rapidly implementable and can be used in real-time simulation and control of the passive DMFC. This comprehensive model can be used for diagnostic purpose as well.     

Highly efficient conversion of sugarcane bagasse pretreated with liquid hot water into ethanol at high solid loading

Liquid hot water (LHW), an environmental-friendly physico-chemical treatment, was applied to pretreat the sugarcane bagasse (SCB). Tween80, a non-ionic surfactant, was used to enhance the enzymatic hydrolysis of the pretreated SCB. It found that 0.125 mL Tween80 /g dry matter could make the maximum increase (33.2%) of the glycan conversion of the LHW-pretreated SCB. A self-designed laboratory facility with a plate-and-frame impeller was applied to conduct batch hydrolysis, fed-batch hydrolysis, and the process of high-temperature (50°C) fed-batch hydrolysis following low-temperature (30°C) simultaneous saccharification and fermentation (SSF) which was adopted to overcome the incompatible optimum temperature of saccharification and fermentation in the SSF process. After hydrolyzing LHW-pretreated SCB for 120 h with commercial cellulase, the total sugar concentration and glycan conversion obtained from fed-batch hydrolysis were 91.6 g/L and 68.3%, respectively, which were 9.7 g/L and 7.3% higher than those obtained from batch hydrolysis. With Saccharomyces cerevisiae Y2034 fermenting under the non-sterile condition, the ethanol production and theoretical yield obtained from the process of SSF after fed-batch hydrolysis were 55.4 g/L and 88.3% for 72h, respectively, which were 15.5 g/L and 24.7% higher than those from separate fed-batch hydrolysis and fermentation. The result of this work was superior to the reported results obtained from the LHW-pretreated SCB.     

Global trends and development of energy services industry in China

Energy service is an effective way to promote energy conservation by market mechanisms, including energy saving services, energy procurement, supply of many varieties of energy, supply of renewable energy technologies, energy-related consulting services, risk management, etc. China is a major energy consumer but energy is in short supply, and the efficiency of energy use is low. China’s energy service industry has expanded rapidly, in terms of both the number of new Energy Service Companies entering the market and amount of capital invested in Energy Performance Contracting projects, but the energy service sector in China is still at an early stage of development. Developed countries began early in developing the energy service sector and their energy service market is mature, and the experience of developed countries shows that energy services play a significant role in advancing energy saving and emission reduction. Under the new situation, China needs combine energy services experience of developed countries, and take following measures to accelerate China’s energy services rapid and healthy development, including the long-term aspects of policy planning, energy-saving core technology, finance and capital investment, public sector reductions, personnel training, and so on.