雅砻江锦屏二级水电站减水河段生态需水量研究

针对雅砻江锦屏二级水电站减水河段面临的水生生物生态需水问题,提出了计算河道最小生态基流量的生态水力学法,考虑了水力生境参数的全河段变化情况,计算结果避免了单凭最低值进行判断所造成的判断失误。确定了锦屏二级水电站减水河段鱼类对流速、水深、水面宽等水力生境的需求。通过河道水力模拟,得出为满足减水河段鱼类的生存及繁衍,必须保证枯水季节猫猫滩闸址下泄45 m3/s流量,在该流量下,锦屏二级水电站减水河段中95%左右河段水力因子可满足研究中提出的河道内鱼类的生存条件;水温的变化不会影响河道内鱼类产卵;鱼类适应的缓流水、急流水、浅滩、深潭等水力形态的位置虽然发生变化,但数量保持不变。     

Dissipation of Tidal Energy and Associated Mixing in a Wide Fjord

This paper sets out to test the hypothesis that vertical mixing due to the dissipation of the internal tide accounts for a significant proportion of the total vertical mixing in a fjordic basin during a period of deep water isolation. During July and August 1999 two locations in the Clyde Sea were instrumented with moored RD Instruments Acoustic Doppler Current Profilers (ADCPs) and conductivity-temperature-pressure chains: Station C2, near the shallow entrance sill (55 m water depth), and station C1 in the deep basin (155 m water depth). A bottom pressure recorder was also deployed at station C3 by the seaward entrance to the Clyde Sea in the North Channel of the Irish Sea. A Free-falling Light Yo-yo shear microstructure profiler (FLY) was used to measure the dissipation rate of turbulent kinetic energy (TKE) throughout the water column over 25 h at both C1 and C2. These were interspersed with two-hourly conductivity-temperature-depth casts at both sites. The observations show agreement between the dissipation rate of TKE estimated by using a microstructure profiler and that estimated from the decay of the internal tide as measured by the two ADCPs. However, to account for all the implied mixing it is necessary to invoke an additional source of buoyancy flux, the most probable candidate mechanism is enhanced internal wave breaking near the sill and at the sloping boundaries of the deep basin. In addition, the vertical eddy diffusivity estimated from the micro-structure profiler (O(0.5 cm² s^–1) indicates that internal tide induced mixing away from any boundaries contributed significantly to the overall level of mixing which is required to account for the observed evolution of the deep basin water properties.     

pH-dependent leaching behaviour and other performance properties of cement-treated mixed contaminated soil

Portland cement has been widely used for stabilisation/solidification (S/S) treatment of contaminated soils. However, there is a dearth of literature on pH-dependent leaching of contaminants from cement-treated soils. This study investigates the leachability of Cu, Pb, Ni, Zn and total petroleum hydrocarbons (TPH) from a mixed contaminated soil. A sandy soil was spiked with 3000 mg/kg each of Cd, Cu, Pb, Ni and Zn, and 10,000 mg/kg of diesel, and treated with ordinary Portland cement (CEM I). Four different binder dosages, 5%, 10%, 15% and 20% (m/m) and different water contents ranging from 13%-19% dry weight were used in order to find a safe operating envelope for the treatment process. The pH-dependent leaching behaviour of the treated soil was monitored over an 84-day period using a 3-point acid neutralisation capacity (ANC) test. The monolithic leaching test was also conducted. Geotechnical properties such as unconfined compressive strength (UCS), hydraulic conductivity and porosity were assessed over time. The treated soils recorded lower leachate concentrations of Ni and Zn compared to the untreated soil at the same pH depending on binder dosage. The binder had problems with Pb stabilisation and TPH leachability was independent of pH and binder dosage. The hydraulic conductivity of the mixes was generally of the order, 10^-8 m/sec, while the porosity ranged from 26%-44%. The results of selected performance properties are compared with regulatory limits and the range of operating variables that lead to acceptable performance described.     

BAF去除氨氮关键影响因素研究

为探讨曝气生物滤池去除氨氮的关键因素,选取沈阳仙女河污水处理厂(40万t/d)现场进行实地研究。通过测定不同条件下(pH、进水COD浓度、溶解氧、温度、水力负荷)的氨氮去除率,并进行主成分分析结果显示,影响BAF工艺脱氮的关键因素是温度、溶解氧和水力负荷。当温度在14~30℃之间时,氨氮的去除率一直维持较高,当温度低于14℃时,氨氮的去除率较低;随着溶解氧浓度的增大,氨氮的去除率也随之升高,当溶解氧增加到5.6 mg/L时,氨氮的去除率达到80%~90%,接近饱和状态;在水力负荷为3.08~4.15 m3/(m.2h)之间时,氨氮的去除率上升,超过该值,则氨氮去除率下降。     

水力停留时间和溶解氧对陶粒CANON反应器的影响

以人工配制无机高氨氮废水为进水,通过接种CANON污泥,以陶粒作为填料,研究了HRT和DO对生物膜CANON反应器的影响.试验过程中,控制进水氨氮浓度基本不变,依次控制反应器的HRT为9、7、5 h,同时控制DO的范围为1.16~3.20 mg·L-1.研究发现:1当DO为1.20~1.75 mg·L-1时,尽管提高DO有利于提高AOB的活性和系统内基质的传质效果,但是CANON反应器的NH+4-N、TN去除效果依然随着HRT的缩短而下降,尤其当DO超过2.50 mg·L-1时,TN去除效果大幅度下降;2当DO为1.20~1.75 mg·L-1时,随着HRT的缩短,CANON反应器的短程硝化性能趋于稳定,而当DO超过1.75 mg·L-1时,即使缩短HRT,其短程硝化性能依然遭到严重破坏;3CANON反应器中短程硝化稳定性能和去除效果较佳的条件是HRT为7 h,且DO控制在1.20~1.75 mg·L-1之间.HRT和DO是废水生物处理的重要运行参数,直接影响到生物处理的效果和出水水质,协调控制两者的变化范围,对提高CANON工艺对高氨氮废水的处理效果非常重要.     

北京怀柔O3污染过程初始VOCs浓度特征及来源分析

为了解北京怀柔区夏季典型O₃污染过程中初始VOCs（挥发性有机物）浓度（以φ计）的特征,识别其关键物种及主要来源,于2016年8月3-11日在中国科学院大学雁栖湖校区教学楼顶开展强化观测,利用光化学物种比值法和连续反应模型法测算观测期间大气初始φ（VOCs）,采用MIR（最大增量反应活性）法估算初始VOCs的OFP（O₃生成潜势）,识别关键物种,并应用PMF（正交矩阵因子）模型对初始VOCs的来源进行解析.结果表明:北京怀柔区O₃污染过程中初始φ（VOCs）平均值为25.27×10-9,如忽略化学损失,φ（VOCs）将被低估约18.6%.初始VOCs的总OFP值为144.6×10-9,VOCs物种对总OFP贡献率的顺序依次为醛酮类>烯烃>芳香烃>烷烃,异戊二烯、乙醛、己醛、间/对-二甲苯、甲苯、乙烯、丙烯、1,2,4-三甲苯、丁酮、1,3,5-三甲苯是怀柔区O₃形成的关键活性物种.PMF解析结果显示,机动车尾气源对初始φ（VOCs）的贡献率（23.5%）最高,其次是溶剂使用源（18.3%）、植物排放源（18.1%）、工业过程源（17.6%）、生物质燃烧源（12.1%）和煤炭燃烧源（10.5%）.研究显示,在北京怀柔区典型O₃污染过程中,减少机动车尾气源、溶剂使用源、上风向工业过程源的排放是控制怀柔区VOCs的有效措施,而控制异戊二烯、乙醛、己醛、间/对-二甲苯、甲苯等关键活性物种则是有效抑制VOCs排放对O₃生成贡献的重要手段.      

ANAMMOX富集与优化停曝比对MBR-SNAD工艺的影响

采用膜生物反应器（MBR）研究了厌氧氨氧化细菌在富集过程中的活性变化,在启动全程自养脱氮（CANON）工艺中以恒定曝气量,通过优化停曝比实现氨氧化细菌（AerAOB）和厌氧氨氧化细菌（AnAOB）协同脱氮并且有效抑制亚硝酸盐氧化菌（NOB）的活性,然后添加有机物（乙酸钠）逐步启动同步亚硝化-厌氧氨氧化耦合异养反硝化（SNAD）工艺.结果表明,在厌氧氨氧化细菌富集过程中,通过不断缩短水力停留时间（HRT）提高进水氮负荷的方式强化厌氧氨氧化细菌活性,其平均活性由0.603mgN/（h·gVSS）提高到了8.1mgN/（h·gVSS）;当恒定曝气量为50mL/min,停曝比为4：10（min：min）时,AerAOB和AnAOB对氨氮的去除量分别占总氨氮去除量的58.8%和41.2%,NOB氧化亚硝态氮的量占总硝态氮生成量的15.3%,成功抑制了NOB的活性;当C/N比为0.5,调整停曝比为4：15后,反硝化过程氮去除量占总氮去除率的20.9%,厌氧氨氧化过程氮去除量占总氮去除率的79.1%,实现了AerAOB、AnAOB和反硝化细菌（DNB）协同脱氮的目的.     

氮和氧同位素示踪伊洛河河水硝酸盐来源及转化过程

河流硝酸盐(NO^-₃)浓度及氮和氧同位素组成(δ¹⁵N-NO^-₃和δ¹⁸O-NO^-₃)可以辨识河水NO^-₃受自然过程和人为输入的影响,但流域不同土地利用方式对河水NO^-₃来源及转化过程的影响尚不明确,特别是山区人为输入对河水NO^-₃的影响仍不清楚.选择土地利用空间异质性显著的伊河和洛河作为研究对象,借助水体水化学组成,氢氧同位素(δD-H₂O和δ¹⁸O-H₂O)、δ¹⁵N-NO^-₃和δ¹⁸O-NO^-₃,辨识不同土地利用方式影响下河水NO^-₃来源及...     

蓄水、调水、发电，扼制生态环境恶化

蓄水是根本，调水是手段，发电是关键。植树造林和拦河筑坝建设水库电站以及沟渠塘蓄水，可以防止水土流失和水能浪费；调水可以解决横向和纵向水资源分布不平衡带来的问题；发电可以解决调水所需动力和全国缺电的问题。其经济效益约合２０００亿元，而且还能扼制生态环境的恶化，减少每年４６．６×１０４ｈｍ２土地的损失，缓解荆江大堤和黄河下游大堤越筑越高之危。     

Modelling the migration of contaminants through variably saturated dual-porosity, dual-permeability chalk

In the Hesbaye region in Belgium, tracer tests performed in variably saturated fissured chalk rocks presented very contrasting results in terms of transit times, according to artificially controlled water recharge conditions prevailing during the experiments. Under intense recharge conditions, tracers migrated across the partially or fully saturated fissure network, at high velocity in accordance with the high hydraulic conductivity and low effective porosity (fracture porosity). At the same time, a portion of the tracer was temporarily retarded in the almost immobile water located in the matrix. Under natural infiltration conditions, the fissure network remained inactive. Tracers migrated downward through the matrix, at low velocity in relation with the low hydraulic conductivity and the large porosity of the matrix. Based on these observations, Brouyère et al. (2004a) [Brouyère, S., Dassargues, A., Hallet, V., 2004a. Migration of contaminants through the unsaturated zone overlying the Hesbaye chalky aquifer in Belgium: a field investigation, J. Contam. Hydrol., 72 (1-4), 135-164, doi: 10.1016/j.conhyd.2003.10.009] proposed a conceptual model in order to explain the migration of solutes in variably saturated, dual-porosity, dual-permeability chalk. Here, mathematical and numerical modelling of tracer and contaminant migration in variably saturated fissured chalk is presented, considering the aforementioned conceptual model. A new mathematical formulation is proposed to represent the unsaturated properties of the fissured chalk in a more dynamic and appropriate way. At the same time, the rock water content is partitioned between mobile and immobile water phases, as a function of the water saturation of the chalk rock. The groundwater flow and contaminant transport in the variably saturated chalk is solved using the control volume finite element method. Modelling the field tracer experiments performed in the variably saturated chalk shows the adequacy and usefulness of the new conceptual, mathematical and numerical model.