A detailed kinetic investigation on the effects of hydrogen enrichment on the performance of gas-fueled SI engine

This study investigates the effects of hydrogen enrichment on formation of pollutants and greenhouse gases in gas-fueled spark ignition engines. To this end, a previously validated detailed mechanism is embedded with a comprehensive one-dimensional engine model and the results are verified with experimental observations at different compression ratios and engine loads. The simulations are then performed for different mixtures of hydrogen and natural gas. The results indicate that adding hydrogen increases the cylinder peak pressure at different loads and compression ratios, despite the fact that reduces the amount of carbon monoxide, carbon dioxide, and methane in all the conditions.     

Super effective Zn-Fe-doped TiO2 nanofibers as photocatalyst for ammonia borane hydrolysis

In this study, the photocatalytic activity of TiO₂ nanofibers toward ammonia borane hydrolysis has been strongly modified by doping the nanostructure by ZnO and Fe₂O₃ oxides. Due to the differences in the work function and band gap energy among the three semiconductors (TiO₂, ZnO and Fe₂O₃), illumination of TiO₂ leads to accumulate the electrons and holes on the conduction and valance bands of Fe₂O₃ and ZnO, respectively. Accordingly, the experimental results indicated that the surface of the obtained nanofibers is very active which results in an instant hydrolysis of ammonia borane molecules reaching the active zone surrounding the nanofibers. Moreover, negative activation energy was determined as increasing the temperature led to decrease the photocatalytic performance. Furthermore, kinetic studies indicated that the heterogeneous catalytic reaction describing the ammonia borane hydrolysis process is zero order which additionally supports the super activity of the introduced nanofibers. It was also observed that Fe₂O₃ content in the introduced nanofibers has distinct influence as the best performance was obtained at 1 wt%. The modified TiO₂ nanofibers were prepared by calcination of electrospun nanofibers composed of titanium isopropoxide, zinc acetate and iron acetate in air at 700 °C for 1 h. Overall, the present study opens a new avenue to overcome the fast electrons/holes recombination dilemma facing TiO₂-based nanostructures.     

成都次降水稳定氢氧同位素特征及水汽来源分析

基于对成都地区2016年9月至2017年10月采集的113场次降水样品氢氧同位素的分析,发现大气次降水中δD、δ~(18)O、~(17)O、d-excess和~(17)O-excess有显著的季节性变化,旱季高雨季低,反映了该地区旱、雨两季水汽来源不同;地区大气降水线斜率和截距都偏小,表明成都降水来源于具有不同稳定同位素比率的源地,且雨滴在降落过程中发生了二次蒸发;三氧同位素大气降水线(δ'~(17)O=0. 528 9δ'~(18)O+0. 007 5)斜率介于海洋气团(0. 529)与干空气(0. 518)之间,表明成都地区处于海洋气团向内陆迁移的路径上; d值接近全球平均值,而~(17)O-excess值远较海水大,表明成都的水汽来源由海洋气团主导,且到达该地区的过程中同位素经历了严重的富集; d-excess在旱季出现的极低值可能是受到了人工降雨的影响,~(17)O-excess除了与水汽源地的相对湿度有关外,还会受到上游气团对流作用的影响,此外,成都当地的气象因素对不同季节次降水的~(17)O-excess值有不同程度的影响.     

分光光度法测定氯化氢的实验条件改进

硫氰酸汞分光光度法测定大气中的氯化氢,所使用的硫氰酸汞-乙醇溶液配置时间长,浓度低,曲线线性不好,不适用于环境现场监测。通过对氯化氢测定过程中遇到的问题进行分析,对硫氰酸汞-乙醇溶液的配置方法进行改进,提高该溶液的浓度。实验证明,使用定性滤纸过滤后的0.40%硫氰酸汞-乙醇溶液,曲线线性关系好,标样准确度高,适用于现场监测分析。     

In situ preparation of g-C3N4/polyaniline hybrid composites with enhanced visible-light photocatalytic performance

The graphic carbon nitride/polyaniline (g-C₃N₄/PANI) hybrid composites were successfully synthesized by a facile in situ polymerization process under ice water bath. The photocatalytic activities of the g-C₃N₄/PANI composites were evaluated by using oxytetracycline (OTC) as model pollutants. The optimal g-C₃N₄/PANI composite (5%PANI: the g-C₃N₄/PANI hybrid with 5 wt.% of PANI) showed an enhancement degradation rate of 5-fold compared to that of conventional g-C₃N₄ under simulated-sunlight irradiation. In addition, the 5%PANI demonstrate significantly photocatalytic evolution H₂ rate (163.2 μmol/(g?hr)) under the visible light irradiation. Furthermore, based on the results of optical performance and electrochemical testing, a possible mechanism was proposed, indicating that the incorporation of PANI into the traditional g-C₃N₄ can effectively tune the electronic structures, improve the photo-generated electrons-holes separation and enhance extensive absorption of visible light. Such a g-C₃N₄/PANI hybrid nanocomposites could be envisaged to possess great potentials in practical wastewater treatment and water splitting.     

载铁ACF/Ni阴极电化学体系除藻效能与机制

采用化学浸渍法将Fe@Fe₂O₃纳米线负载在活性炭纤维/泡沫镍上组成Fe@Fe₂O₃/ACF/Ni复合阴极,以钛基铂（Pt/Ti）为阳极,考察载铁量、初始pH值和不同电化学体系对除藻效果的影响,探究无供氧条件下Pt/Ti-Fe@Fe₂O₃/ACF/Ni电化学体系除藻的效能;基于·OH间接检测、铁离子浓度、H₂O₂浓度及pH值的分析和·O₂^-的检测研究Pt/Ti-Fe@Fe₂O₃/ACF/Ni中性电化学体系反应机制.结果表明,当制备阴极阶段投加0.03g FeCl₃×6H₂O,初始藻浓度为0.7×10⁹~0.8×10⁹个/L,电流密度为75mA/cm²,初始pH6.2时,电解60min,该体系除藻率可达到92.3%.在Pt/Ti-Fe@Fe₂O₃/ACF/Ni电化学体系中,Fe@Fe₂O₃/ACF/Ni阴极可通过电化学反应产生大量·OH和·O₂^-,使藻细胞破裂死亡;该体系除藻的主要机理是非均相电Fenton反应.     

西藏巴松措冷季水化学特征及其影响因素

于2018年12月（冷季）,结合水体现场理化参数和入湖河流,湖泊表层,湖泊垂直分层及出水口各样点水样分析结果对其水化学组成和分布特征以及影响因素进行了研究.结果表明,冷季巴松措水体呈弱碱性.湖区TDS含量较低,平均值仅达107mg/L.湖区平均水温为5.7℃,在水深45~60m范围内存在温度跃变,但变化梯度较小.空间上,各现场理化参数值从入湖河流到湖泊表层且沿垂直方向至最深处均有一定的变化规律,但是这些变化并无显著性差异（P>0.05）.巴松措湖泊水体溶解相中,Ca²⁺和HCO₃^-为主导离子,分别占阳离子和阴离子总量的80.35%和72.95%.各主要离子浓度在平面空间分布上表现为入湖河流高于湖泊表层,汇入湖泊后趋于平稳的趋势.在垂直空间分布上却呈随水深增加而轻微增大的趋势.巴松措水化学类型为HCO₃·SO₄-Ca型.流域内受岩石风化作用的影响,特别是碳酸盐岩的风化过程是影响巴松措水化学组成和分布特征的主要控制因素.     

亚砷酸钠对酵母细胞H2S代谢的影响

以模式生物酿酒酵母为研究对象,采用醋酸铅试纸条法、BIGGY琼脂及qRT-PCR技术检测了不同浓度亚砷酸钠胁迫下H₂S产量及产H₂S酶编码基因表达的变化,以探讨砷化物对酵母细胞H₂S代谢的影响.结果显示,0.5~2 mmol·L^-1的亚砷酸钠可诱导酵母细胞内源H₂S的产生,且H₂S合成相关基因的相对表达量与对照相比均有不同程度的上调.经0.05~0.2 mmol·L^-1的外源H₂S预处理后,酵母细胞对砷的耐受性明显提高.研究表明,亚砷酸钠可影响酵母细胞H₂S代谢,而H₂S含量可在一定程度上调控砷对酵母的毒性.     

南京市不同功能区冬季大气PM2.5分布特征及其来源解析

2016年12月-2017年1月,在南京市4类典型功能区（农业区、住宅区、交通干道区、工业区）各选两点,共采集了大气PM_2.5样品32套,测定并分析了其质量浓度、9种水溶性离子（WSIs）、有机碳（OC）以及元素碳（EC）的含量.观测期间,南京市冬季PM_2.5的平均浓度为104.5 μg·m^-3,分布特征为：工业区（116.6 μg·m^-3）>农业区（104.3 μg·m^-3）>住宅区（100.1 μg·m^-3）>交通干道区（96.9 μg·m^-3）;WSIs、OC和EC的平均浓度（/PM_2.5）分别为：53.4 μg·m^-3（51.1%）、11.8 μg·m^-3（11.3%）、8.2 μg·m^-3（7.8%）.农业区和住宅区受WSIs污染较严重且NOR、SOR较高,而工业区和交通干道区的OC、EC污染较严重且SOC/OC较高.进一步运用PMF模型解析,南京市冬季PM_2.5来源为：二次源（37.3%）、工业源（31.2%）、交通源（16.4%）、建筑尘（7.9%）和燃煤源（7.2%）.最后,本文收集了自2000年起南京市冬季大气PM_2.5浓度及其污染来源研究,总体而言,近年来南京冬季大气PM_2.5浓度呈下降趋势,其主要污染源比重也发生了较大变化,燃煤贡献有所下降,而工业和交通排放逐渐上升,且二次污染贡献逐渐突出.今后,控制二次污染源将成为南京市大气PM_2.5治理的重中之重.     

长三角沙尘中气溶胶粒径分布及化学组分特征

基于PM、10nm~10μm气溶胶数谱、水溶性离子和气象要素数据,分析了2017年5月3日~8日一次沙尘远距离输送过程中长三角地区气溶胶粒径分布及其化学组成的污染特征.结果表明,此次沙尘伴随天气系统由北往南的传输过程中,PM的浓度逐渐降低,但是高浓度PM持续时间逐渐增加.沙尘在呼和浩特市影响时间为38h,而在南京的影响时间超过60h.沙尘期间气溶胶数浓度谱的峰值向大粒径段偏移,沙尘和非沙尘期间峰值分别位于33和26nm.表面积浓度谱在非沙尘期间为三峰型分布,但是在沙尘期间为四峰型分布.在沙尘期间PM_2.5和PM₁₀中水溶性离子的排序为Ca²⁺ > NH₄⁺ > SO₄^2- > NO₃^- > Mg²⁺ > Na⁺ > Cl^- > NO₂^- > K⁺ > F^-,非沙尘期间为NH₄⁺ > SO₄^2- > NO₃^- > Mg²⁺ > Ca²⁺ > Cl^- > NO₂^- > K⁺ > Na⁺ > F^-.沙尘期间不同水溶性离子的浓度变化不同,沙尘天PM_2.5和PM₁₀中Ca²⁺浓度分别是非沙尘天的9.5和13.7倍,Na⁺分别是非沙尘天的4.4倍和4.6倍.沙尘天PM_2.5和PM₁₀中Ca²⁺占总离子的比例分别为24.7%和24.9%,是非沙尘天的4.9和5.7倍.NO₃^-在PM₁₀中的占总离子的比例为18.7%,高于非沙尘天（13.9%）,但是在PM_2.5中占总离子的比例仅为7.9%,低于非沙尘天（13.2%）.沙尘天F^-、Cl^-、SO₄^2-、NH₄⁺和K⁺离子在PM_2.5和PM₁₀中所占总离子的比例均低于非沙尘天.