垃圾焚烧发电厂脱硝技术及应用

介绍了垃圾焚烧烟气烧脱硝控制的主要技术及应用情况,以及非催化还原技术的应用实例,采用该技术,氮氧化物排放值可满足现阶段排放要求。     

钢铁厂烧结烟气SCR脱硝技术应用探讨

目前烧结烟气脱硝主要采用活性炭(焦)吸附技术,投资及运行费用极高。SCR(选择性催化还原)烟气脱硝技术广泛应用于燃煤锅炉,技术成熟可靠。针对钢铁厂烧结烟气的特点,探讨了将SCR烟气脱硝技术应用于烧结烟气脱硝;通过适当的工艺优化和技术创新,烧结烟气采用SCR脱硝技术完全可行,经济适用。     

Operating condition influences on PCDD/Fs emissions from sinter pot tests with hot flue gas recycling

This study was designed to clarify the influence of operating conditions on the formation and emissions of polychlorinated-pdibenzodioxins and dibenzofurans (PCDD/Fs) from a sintering process with hot flue gas recycling. A pilot scale sinter pot with simulated flue gas recycling was developed, and four key operational parameters, including temperature, oxygen content of the simulated waste flue gas, the coke rate of the sintering mixture, and the quicklime quality, were selected for exploring PCDD/Fs formation. The results showed that the temperature of the recycled flue gas had a major affect on PCDD/Fs formation, and a high temperature could significantly increase their formation during sintering. A clear linear correlation between the temperature of recycling flue gas and PCDD/Fs emission (r = 0.93) was found. PCDD/Fs could be reduced to a certain extent by decreasing the level of oxygen in the recycled flue gas, while sintering quality was unchanged. The coke rate had no significant influence on the formation of PCDD/Fs, but the quality of quicklime used in the sintering mixture could affect not only the amount of PCDD/Fs emissions but also the sintering productivity. Compared with a benchmark sinter pot test, PCDD/Fs emissions markedly decreased with improvements to quicklime quality. However, the reduction in PCDD/Fs emissions realized by using high-quality quicklime was limited by the temperature of the inlet gas. The highest reduction achieved was 51% compared with conventional quicklime when the temperature of the inlet gas was 150°C.     

非烟气工况下常规烟塔与改造烟塔内部结构的比较

根据流体力学理论,基于Fluent6.3.26计算平台,对常规冷却塔和改造后的排烟冷却塔进行了三维内部流场的模拟。分析非烟气工况下,两塔内部烟道布置对气流的影响,为进一步研究在工况条件下烟气、水蒸气塔内扰流与湿热蒸汽抬升作用提供理论基础。验证了改造烟塔内部烟道布置的优越性,对排烟冷却塔结构优化有一定的指导意义。     

火电湿法烟气脱硫流程优化的实现方案研究

在给定脱硫流程模拟优化参数的情况下,尝试了基于DCS系统和基于OA局域网的两种优化控制改进方案,后一种方案解决了优化控制系统的安全性、稳定性、扩展性、易管理等问题。同时采用该控制系统的3号脱硫系统的控制效果最佳,且脱硫效率循环浆液泵功率比随着操作方式相近度的提高而呈递增趋势。     

氨法烟气脱硫循环液沉降试验研究

通过湿法烟气脱硫副产硫酸铵生产工艺中的循环母液混凝试验,讨论母液的沉降性能,初步探讨母液被循环浓缩的程度对混凝处理效果的影响。     

燃煤电厂排放细颗粒物的水溶性无机离子特征综述

当前我国面临严重的大气细颗粒物(PM2.5)污染,燃煤电厂是大气中PM2.5的重要来源之一.为了实现国家"十一五"和"十二五"规划对二氧化硫(SO2)和氮氧化物(NOx)的总量减排目标,燃煤电厂大规模安装烟气脱硫和脱硝设施,这虽然减少了气态污染物转化生成的二次PM2.5,但另一方面也会对烟气中PM2.5的物理化学特征产生影响,有可能增加一次PM2.5的排放.本文综述了燃煤电厂排放PM2.5及其水溶性离子的粒径分布特征,重点介绍了脱硫和脱硝这两种烟气处理设施对燃煤电厂排放PM2.5的影响原理及相关研究结果,特别是对细颗粒物中水溶性离子(如SO2-4、Ca2+和NH+4)的影响.在目前我国PM2.5污染十分严重和燃煤电厂大量安装脱硫和脱硝装置的背景下,定量研究脱硫和脱硝对PM2.5排放特征的影响具有十分重要的意义.     

轮作方式对冬水田温室气体排放的影响

以位于西南大学农业部重庆紫色土生态环境重点野外科学观测试验站内的冬水田(RF)、水稻-油菜轮作(RR)和水稻-儿菜轮作(RV)农田为研究对象,采用静态箱-气相色谱法对农田的温室气体的排放通量进行了为期一年的原位观测,其中采用静态暗箱技术观测CH4和N2O,静态明箱技术观测CO2.结果表明,不同轮作方式下CH4的年排放总量[以CH4计,kg·hm-2]RF(422.87±27.1) RR(132.05±23.11) RV(50.91±3.83),其中RV与RR处理较RF处理CH4排放量有明显下降(P0.05);N2O的年排放总量[以N2O计,kg·hm-2]依次为RV(21.38±6.51) RR(20.02±5.23) RF(0.48±0.02),RV和RR处理N2O的排放总量均显著高于RF(P0.05);CO2的年净排放总量[以CO2计,t·hm-2]为RR(-55.43±5.04) RV(-29.1±3.00) RF(-14.08±1.81),RV和RR处理CO2的吸收量显著高于RF处理(P0.05).在100a时间尺度上,全年排放的CH4、N2O和CO2所引起综合GWP(以CO2计,t·hm-2)为RR(-46.43) RV(-22.01) RF(-2.11),表明冬水田转变为水旱轮作系统后能显著提升农田生态系统的增汇效果,相比于RV处理,RR处理增汇效果更好,即在西南地区水稻-油菜轮作农田在生态系统增汇上是一种最有效的轮作方式.     

典型平原地区生活垃圾焚烧厂周边土壤重金属赋存形态分布特征及生物有效性评价

为考察并掌握典型平原地区生活垃圾焚烧厂周边土壤中重金属Cd、Cr、Cu、Pb、Ni和Zn的污染现状,以上海市某生活垃圾焚烧厂为例,研究其周边土壤中重金属赋存形态分布特征及生物有效性,采用Tessier连续提取法结合电感耦合等离子体发射光谱检测分析表层土壤中目标重金属总量及形态分布,并利用风险评估编码法（RAC）评价其生态风险水平.结果表明:研究区域土壤中Pb和Zn主要以Fe-Mn氧化物结合态和残渣态为主（>80%）;Cr、Cu和Ni则以残渣态为主（>60%）;Cd虽以残渣态为主（>50%）,但与其他重金属相比,其碳酸盐结合态占比相对较高.生物有效性分析结果显示,Cr、Cu和Ni以惰性态为主,生物有效性低,而潜在可利用态Cd、Pb和Zn占比较高,存在较高的释放风险.土壤中各重金属潜在生态风险水平由高到低依次为Cd > Zn > Pb > Cu > Ni > Cr,其中,Cu、Pb和Zn处于低风险水平,Cr和Ni处于无风险水平,而Cd处于中等风险水平.研究显示,该垃圾焚烧厂周边土壤中重金属已存在不同程度的污染累积,其中,潜在可利用态Cd的占比较高,已达中等风险水平,应引起重视.      

Formation of dioxins from combustion of polyvinylidene chloride in a well-controlled incinerator

Polyvinylidene chloride (PVDC; polymer of 1,1-dichloroethylene) was combusted with paper in a well-controlled, small-scale incinerator at an average grate temperature of 700 °C, and then dioxins (PCDDs, PCDFs, and coplanar-PCBs) formed in the exhaust gases were analyzed by gas chromatography/mass spectrometry. PVDC lowered the combustion temperature due to its less flammable character. The amount of total dioxins (PCDDs + PCDFs + coplanar-PCBs) formed in the exhaust gas was 58.0 ng/g of a combustion sample and its toxicity equivalency quantity (TEQ) value was 0.64 ng-TEQ/g. The amount of PCDDs formed in the sample ranged from 2.33 ng/g (Cl₈-isomer) to 0.048 ng/g (Cl₁-isomer). The lower the number of chloride, the less production of PCDDs. On the other hand, there was no relation between the number of chloride and PCDF formation. The amount of PCDFs formed in the sample ranged from 8.02 ng/g (Cl₂-isomer) to 4.46 ng/g (Cl₈-isomer). A polyvinylchloride (PVC) sample produced 207 ng/g of total dioxins and a PVDC sample produced 57.4 ng/g of total dioxins when they were combusted under the same conditions. An approximately equal composition of dioxin isomers was formed from PVDC and PVC samples. Paper was found to contribute to PCDF formation when it was combusted with plastics.