城市污水处理厂进水浓度偏低原因分析及对策研究

城市污水处理厂进水浓度偏低是南方地区许多城市面临的共同问题,既影响废水主要污染物COD的减排成效,制约水环境质量的改善,也在一定程度上造成城市污水处理工程的投资浪费.以张家界市中心城区污水处理厂为例,通过现场勘测与监测分析,考察了管网渗漏、雨污合流、地表水渗入、管网反坡和管网颗粒物沉积等因素,探究造成该市城市污水处理厂进水浓度偏低的主要原因,并在此基础上提出有针对性的对策建议,供管理部门参考.     

基于Shapley值的农村非政府应急组织激励模型构建

农村非政府应急组织是以共同应对农村突发事件为纽带自愿结成的互助性合作联盟,成员间的利益分配关系是组织生存与发展的重要基础。而Shapley值法正是解决多人合作利益分配问题的一种简便易行的数学方法。基于Shapley值法构建农村非政府应急组织利益分配激励模型能较好地促进其成员间的信任、合作与共享信息,使其收益透明化,有助于全面提升应急服务效益和充分发挥应急服务功能。首先,介绍了基于Shapley值法构建农村非政府应急组织激励模型的研究现状,然后初步探索了构建步骤及其实施建议,以进一步促进农村非政府应急组织的稳定运行与健康发展。     

Volatile organic compounds at swine facilities: A critical review

Volatile organic compounds (VOCs) are regulated aerial pollutants that have environmental and health concerns. Swine operations produce and emit a complex mixture of VOCs with a wide range of molecular weights and a variety of physicochemical properties. Significant progress has been made in this area since the first experiment on VOCs at a swine facility in the early 1960s. A total of 47 research institutions in 15 North American, European, and Asian countries contributed to an increasing number of scientific publications. Nearly half of the research papers were published by U.S. institutions.Investigated major VOC sources included air inside swine barns, in headspaces of manure storages and composts, in open atmosphere above swine wastewater, and surrounding swine farms. They also included liquid swine manure and wastewater, and dusts inside and outside swine barns. Most of the sample analyses have been focusing on identification of VOC compounds and their relationship with odors. More than 500 VOCs have been identified. About 60% and 10% of the studies contributed to the quantification of VOC concentrations and emissions, respectively. The largest numbers of VOC compounds with reported concentrations in a single experimental study were 82 in air, 36 in manure, and 34 in dust samples.The relatively abundant VOC compounds that were quantified in at least two independent studies included acetic acid, butanoic acid (butyric acid), dimethyl disulfide, dimethyl sulfide, iso-valeric, p-cresol, propionic acid, skatole, trimethyl amine, and valeric acid in air. They included acetic acid, p-cresol, iso-butyric acid, butyric acid, indole, phenol, propionic acid, iso-valeric acid, and skatole in manure. In dust samples, they were acetic acid, propionic acid, butyric acid, valeric acid, p-cresol, hexanal, and decanal. Swine facility VOCs were preferentially bound to smaller-size dusts.Identification and quantification of VOCs were restricted by using instruments based on gas Chromatography (GC) and liquid chromatography (LC) with different detectors most of which require time-consuming procedures to obtain results. Various methodologies and technologies in sampling, sample preparation, and sample analysis have been used. Only four publications reported using GC based analyzers and PTR-MS (proton-transfer-reaction mass spectrometry) that allowed continuous VOC measurement. Because of this, the majority of experimental studies were only performed on limited numbers of air, manure, or dust samples. Many aerial VOCs had concentrations that were too low to be identified by the GC peaks.Although VOCs emitted from swine facilities have environmental concerns, only a few studies investigated VOC emission rates, which ranged from 3.0 to 176.5 mg d⁻¹ kg⁻¹ pig at swine finishing barns and from 2.3 to 45.2 g d⁻¹ m⁻² at manure storages. Similar to the other pollutants, spatial and temporal variations of aerial VOC concentrations and emissions existed and were significantly affected by manure management systems, barn structural designs, and ventilation rates.Scientific research in this area has been mainly driven by odor nuisance, instead of environment or health concerns. Compared with other aerial pollutants in animal agriculture, the current scientific knowledge about VOCs at swine facilities is still very limited and far from sufficient to develop reliable emission factors.     

电除尘器进气烟箱参数对气流分布影响的仿真研究

电除尘器进气烟箱结构参数不仅对除尘器内部气流分布的均匀性产生重要影响,而且还会影响除尘效率和排放指标。针对电除尘器进气烟箱结构参数选取与气流分布均匀性问题,采用欧拉-拉格朗日多相流模型,对进气烟箱扩散角,气流分布板孔形、开孔率和导流板角度等参数,进行了三维流场模拟仿真计算,获得各参数对气流均匀性的影响关系规律。仿真结果表明:方形孔的气流分布板能获得较佳的气流分布均匀性;合理调节进气烟箱扩散角、开孔率和导流板角度可有效地改善电场内气流分布状况。研究结果可为电除尘器进气烟箱的设计与改进提供依据。     

多水源供水管网中铁释放规律

针对水源切换而引起的水质超标现象,开展了多水源联合供水条件下管网中铁释放规律的研究。分析了北方某城市2种水源(滦河水和长江水)的水质特点,利用实验模拟反应器分别研究了水源完全置换和供水分界线处水源混合区域的铁释放规律。结果表明,多水源供水管网的铁释放速率与水源水质密切相关,特别是水中含高浓度SO2-4和氯化物时会加快铁的释放。不同水源之间的频繁切换会破坏管垢表面的钝化层,使铁释放速率迅速变化,随后会有所缓解,但新的平衡的形成需要较长时间。供水分界线处的水源混合区域,由于水质的不断变化造成管垢表面很难形成稳定的钝化层,铁释放速率持续偏高,只有当长江水所占比例高达75%以上时才能得到抑制。     

餐厨垃圾和绿化废弃物换向通风好氧堆肥

以某高校餐厨垃圾和绿化废弃物为原料,利用一种换向通风的堆肥降解装置对其进行好氧堆肥处理,研究了2个进气温度(35℃、45℃)和3个通风速率(1.5、2.5和4 m3/h)6个处理组对堆肥原料理化性质(堆体温度、含水率、pH值、有机质含量、C/N、种子发芽指数)的影响。餐厨垃圾和绿化废弃物进行15 d好氧堆肥后,pH值上升到7左右,有机质含量达到20%~80%,C/N都降到20以下,种子发芽指数均大于50%。经过1个月腐熟,其含水率≤30%。上述指标符合有机肥料标准(NY525-2011)的要求,该堆肥产物可用于园林绿地,具有显著的经济效益和生态效益。本研究结果表明,将城市餐厨垃圾和绿化废弃物混合后进行好氧堆肥是废弃物处理的高效工程,具有良好的发展前景。     

泉州白濑水利枢纽工程升鱼机进鱼口位置选择研究

水库大坝建设会对鱼类洄游造成阻隔影响,为减少大坝阻隔对鱼类遗传交流的影响,大坝应建设过鱼设施。福建省泉州白濑水利枢纽工程采用升鱼机过鱼设施,而进鱼口位置选择是影响过鱼设施设计成败的关键因素。根据白濑水利枢纽布置特点,从坝下流场、工程条件、过鱼效果等方面进行进鱼口位置比选研究,为类似水库工程过鱼设施进鱼口位置选择提供参考和借鉴。     

电除尘器改造场地局促时进气烟箱的设计

在原地将1套300 MW机组配备的双列双室3电场侧部挠臂锤振打式电除尘器(ESP),改造为双列双室4电场顶部电磁锤振打式ESP时,先将其竖井式进气烟箱的前半部改为结构紧凑的下部进气烟箱,以便在各室增加1个电场。受场地制约,第1、第2层气流均布板设置在壳体之内,导致两板的间距、第2层板与第1电场的间距均小于800 mm。加之取消壳体的进口下端板,因而显著地影响第1电场内的气流分布均匀性。在模型上适当调整导流板和气流均布板的结构之后,第1电场内的气流分布均匀性、粉尘浓度分布均匀性都获得了改善,且ESP内的气体流动形式已成为有利于收尘的上斜式流动。     

沅江入湖河床沉积物重金属污染演化地球化学分析

对沅江入湖河段河床沉积物进行钻探取样,利用电感耦合等离子质谱仪(ICP-MS)分析沉积物重金属等微量元素的含量,并利用210Pb法测定沉积物沉积速率.同时,在分析沉积物重金属污染特征的基础上,探讨沉积物重金属污染的演化过程.结果表明:沉积物中Bi、Cd、Mn、Mo、Zn、Pb等重金属含量变化大、分布不均匀,而Sc、Tl、Rb、Cs、V、Co、Zr、Hf、Nb、Ta、Ga、Ge、Rb、Sr、REEs(稀土元素)等微量元素含量变化小,分布相对均一.微量元素富集特征(EF值)和主成分分析结果显示,沉积物中Cu、Sc、Tl、Rb、Cs、Th、U、V、Co、Zr、Hf、Nb、Ta、Ga、Ge、Rb、Sr、REE等微量元素主要为自然源,而Bi、Cd、Mn、Zn、Pb等重金属则既有自然源的影响,又有人为源的贡献.地累积指数(Igeo)评价结果显示,入湖段沉积物存在Cd-Mn-Zn-Pb-Bi等元素组合的重金属污染,且沉积物自下而上分布有中深部(204~192 cm)、中上部(96~64 cm)、浅表部(64~0 cm)3个重金属污染层.上述3个重金属污染层可能对应于3个期次的重金属污染事件,即早期(1913年前)的零星重金属污染、中期(建国初期至改革开放初期,1963—1979年)的中等强度重金属污染、近期(1979年至今)高强度重金属污染.且自早期到近期,沉积物重金属污染程度增强,污染元素组合趋于复杂化.沅江入湖河床沉积物的上述3期重金属污染可能对洞庭湖沉积物产生直接影响.     

C/SiC复合材料波纹点阵结构进气道前缘设计与制备

目的 C/SiC复合材料进气道前缘轻量化设计与制备。方法基于进气道气动外形和结构要求,建立波纹点阵夹芯结构的进气道前缘有限元模型,然后按照德国航空中心H2K超声速风洞试验室试验的数据进行反演,得到进气道前缘的热流密度分布,据此进行边界条件加载,在模型中考虑固体导热、表面辐射以及空腔辐射三种传热方式。采用瞬态传热算法,求解100 s下进气道前缘的温度场,为了进一步降低C/SiC复合材料波纹点阵结构进气道前缘的最高温度,设计不同的进气道前缘尖端半径,并进行优化。最后根据优化得到的波纹点阵进气道几何参数,采用PIP法制备出C/SiC复合材料点阵结构进气道前缘。结果进气道尖端半径小于0.5mm时,最高温度高于1800℃,超过C/SiC复合材料极限温度;进气道尖端半径大于1.0 mm时,最高温度为1520℃,低于C/SiC复合材料极限温度;进气道尖端半径大于2.0 mm时,增大半径对降低进气道前缘最高温度没有明显的作用。不同进气道前缘尖端半径下,最高温度达到稳态的时间不一样,半径等于0.5 mm时,进气道前缘达到稳态的时间约为30 s左右。随着前缘尖端半径增大,最高温度达到稳态的时间增加,半径为1.0 mm时,达到稳态时间约为60 s。结论进气道前缘最高温度随着尖端半径增大明显降低,当半径大于2.0 mm时,增大半径对降低进气道前缘最高温度没有明显的作用。