油松叶绿体DNA间隔序列特点及系统学意义

对全国分布区12个天然油松种群进行取样,测定了叶绿体DNAtrnT-trnL、trnS-trnG、trnL-trnF基因间隔序列,分析了序列碱基组成特点及在松科系统分类中的意义.测序结果显示,3个片段碱基序列均富含A/T,长度依次为448bp、636bp和421bp,所测片段在种群水平上十分保守,没有发现具有种内鉴别意义的碱基变异.但此片段适合于松科属间和种间的系统学分析,运用PHYLIP软件构建松科植物的邻接系统树,支持松科分为两个亚科的分类系统,拓扑结构表明松属与银杉属的关系最近.由于叶绿体DNA序列长度适中,扩增和测序较为容易,适合作为研究松科植物系统进化较为理想的分子标记.图2表2参24     

Determination of Heat Loss from the Feet and Insulation of the Footwear

This study compared the methods of determining footwear insulation on human participants and a thermal foot model. Another purpose was to find the minimal number of measurement points on the human foot that is needed for insulation calculation. A bare foot was tested at 3 ambient temperatures on 6 participants. Three types of footwear were tested on 2 participants. The mean insulation for a bare foot obtained on the participant and model were similar. The insulation of warm footwear measured by the 2 methods was also similar. For thin footwear the insulation values from the participants were higher than those from the thermal model. The differences could be related to undefined physiological factors. Two points on the foot can be enough to measure the insulation of footwear on human participants (r = .98). However, due to the big individual differences of humans, and good repeatability and simplicity of thermal foot method, the latter should be preferred for testing.     

A Comparison of Two Methods of Determining Thermal Properties of Footwear

The present European Standard for footwear testing (Standard No. EN 344:1992; European Committee for Standardization [CEN], 1992) classifies footwear thermally by a temperature drop inside the footwear during 30 min at defined conditions. Today, other methods for footwear thermal testing are also available. The aim of this study was to compare EN 344:1992 with a thermal foot method. Six boots were tested according to both methods. Additional tests with modified standard tests were also carried out. The methods ranked the footwear in a similar way. However, the test according to standard EN 344:1992 is a pass-or-fail test, whereas data that is gained from the thermal foot method gives more information and allows further use in research and product development. A change of the present standard method is suggested.     

Effect of Sweating on Insulation of Footwear

The study aimed to find out the influence of sweating on footwear insulation with a thermal foot model. Simultaneously, the influence of applied weight (35 kg), sock, and steel toe cap were studied. Water to 3 sweat glands was supplied with a pump at the rate of 10 g/hr in total. Four models of boots with steel toe caps were tested. The same models were manufactured also without steel toe. Sweating reduced footwear insulation 19–25% (30–37% in toes). During static conditions, only a minimal amount of sweat evaporated from boots. Weight affected sole insulation: Reduction depended on compressibility of sole material. The influence of steel toe varied with insulation. The method of thermal foot model appears to be a practical tool for footwear evaluation.     

Testing Sleeping Bags According to EN 13537:2002: Details That Make the Difference

The European Standard on sleeping bag requirements (EN 13537:2002) describes a procedure to determine environmental temperature limits for safe usage of sleeping bags regarding their thermal insulation. However, there are several possible sources of error related to this procedure. The main aim of this work was to determine the influence of the various measuring parameters on the acuity of the respective parameters in order to judge the requirements. The results indicated that air velocity, mattress insulation and time between unpacking the bag and measurement had a significant impact on the result, with a difference of up to 5–15% in thermal insulation between minimum and maximum allowable parameter levels. On the other hand, manikin weight, thickness of the artificial ground and presence of a face mask were found to have a negligible influence. The article also discusses more general aspects of the standard including the calculation methods used.     

KTV、慢摇吧等娱乐场所噪声治理方法研究

近年来,随着KTV,慢摇吧等娱乐场所的增加,娱乐场所带来的噪声扰民问题也日益突出。由于业主、施工单位等缺乏隔声降噪的专业知识,使得这一问题没有很好解决。本文通过对这类噪声的特性分析,根据其具有低频为主、穿透力强、不易衰减等特点,结合工程实例,从提高顶棚、侧墙的隔声量,结构上多采用弹性连接及增加阻尼等角度提出几点治理方法。以隔声、隔振为主,控制这类噪声通过空气传声与固体传声等途径向周围居民区传播。     

生产操作室隔音降噪措施及控制效果的应用研究

通过对石化企业主要噪声源分布、构成情况和生产操作室隔音降噪措施琢控制效果的比较、分析，提出了生产操作室噪声控制和治理的原则、方法和设计方向。     

窗口火作用下建筑幕墙外保温系统防火性能的试验

建筑幕墙外保温系统火灾事故发生频率高,火灾危险性大,其防火安全性能已成为社会关注的焦点。采用大尺度实体火试验方法,选取具有代表性的金属幕墙保温系统和保温装饰板外保温系统作为试验对象,对防火隔离带和防火封堵位于墙体不同位置的4种工况,开展了一系列窗口火试验。通过采集试验表观现象、火焰蔓延特性、温度分布特性、系统损坏特征等耐火性能试验数据,综合比较分析了不同工况下不同燃烧性能等级的建筑幕墙外保温系统的耐火性能。结果表明,建筑幕墙上下贯通的空腔结构加剧了火蔓延的烟囱效应,存在较大的安全隐患。防火封堵可以阻断空腔中的热对流,防火隔离带可以阻隔材料之间的热传导,二者均可以有效抑制火焰在垂直和水平方向上的蔓延,大幅提高建筑幕墙外保温系统的防火性能。在建筑外墙窗口上方、水平线1及水平线2下方20 mm处分别设置宽度为100 mm的防火封堵和宽度为300 mm的防火隔离带时,系统具有较好的防火性能,综合考虑实际工程的应用性和经济性,可将其设为防火构造设计的基准参数。     

泡沫聚合物保温材料的研究进展及其应用

综述了以聚氨酯泡沫、聚乙烯泡沫和酚醛泡沫塑料为代表的轻质聚合物泡沫保温材料的发展状况。     

建筑设备的减振与消声

针对当前高层建筑中建筑设备对环境造成的污染问题，综述了控制和消除噪声的技术措施，强调了在建筑设计中应注意的问题。