复合吸收技术净化复杂工业有机废气

以低浓度、大风量、含无机物、尘粒和油分等成分的复杂工业有机废气为对象,进行复合吸收净化技术的研究,从吸收机制初步探索,对净化设备、工艺流程及工程应用分别进行了探讨.分别以3种不同的表面活性剂溶液为复合吸收剂,考察其处理含甲苯和醋酸丁酯废气的净化效果,结果表明降低复合吸收剂的表面张力,有利于甲苯和醋酸丁酯的去除率.针对复杂工业有机废气,开发高效吸收设备,集合了水膜、旋流板和填料3种吸收净化装置的优点于一体,具有结构简单、体积小、防堵塞及多级高效吸收传质的优势.工艺流程以吸收技术为主,整合了加热吹脱、燃烧和厌氧等工艺,最终使废气和吸收尾液达标排放.该技术已在制造、喷涂等多家企业的工程上应用.     

聚合物/表面活性剂二元体系对油水界面性质的影响

文章应用界面张力仪、Zeta电位仪和表面黏弹性仪测定了聚合物、表面活性剂及其二元复合体系的质量浓度对油水界面性质的影响,并应用透射电镜观察了采出液的液膜结构。结果表明,随着聚合物质量浓度的增加,油水界面的界面剪切黏度值和界面张力值增大,颗粒表面Zeta电位的绝对值增大;随着表面活性剂质量浓度的增加,油水界面的界面剪切黏度变化幅度很小,但界面张力显著减小,颗粒表面Zeta电位绝对值增大;聚合物与表面活性剂复合能够形成稳定的聚合体,具有较大的界面剪切黏度值,较小的界面张力和较高的Zeta电位值;体系中聚合物、表面活性剂及水中悬浮物形成了类似"晶体"结构。     

PM2.5中类腐殖质表面活性测定方法与实例分析

建立了大气细粒子中类腐殖质（HULIS）表面活性的动态表征方法,并以华北平原乡村站点冬季大气PM_2.5样品为例,对PM_2.5中HULIS的表面活性进行表征.HULIS碳质组分（HULIS-C）浓度为2.0~4.6μg C/m³,占水溶性有机碳和总有机碳的比例分别为31%~40%和20%~26%.浓度为88~200mg C/L的HULIS水溶液,其表面张力相对于纯水降低了18%~22%.HULIS-C浓度在低于70mg C/L时表面张力降低显著,在88~320mg C/L之间降低相对缓慢.动态表面张力随着时间变化逐渐降低,在液滴形成后200s以内表面张力下降迅速,之后趋于平缓,说明表面活性分子在液滴中扩散趋于稳定需要一定的时间,该特征时间可能影响表面活性物质在云凝结核活化时的作用.证实了在污染地区的大气PM_2.5中含有一定量的表面活性物质,这些物质可能对颗粒物活化为云滴、雾滴过程产生显著影响;表面活性物质的存在可能在外界湿度变化过程中导致颗粒物发生液-液相分离现象,在颗粒物表面形成有机膜,影响活性分子摄取以及半挥发性物质的气-粒分配过程,从而影响大气非均相反应过程.     

假单胞菌XD-1(Pseuomonas XD-1)的产表面活性剂性能研究

从含油废水中分离到1株表面活性剂产生菌,经鉴定为假单胞菌(Pseuomonassp.),命名为XD 1.对假单胞菌XD 1的产表面活性剂性能进行研究,实验结果表明,在正交优化的培养基中发酵培养时,菌XD 1可将培养液的表面张力从70 0mN·m-1降至30 2mN·m-1,其产表面活性剂方式为生长相关型;经提取分析,菌XD 1所产表面活性剂为脂肽类和糖脂类物质的混合物,脂肽类物质为主要成分;菌XD 1所产表面活性剂的CMC值为50mg·L-1,在pH=6 0时表面活性剂表现出最佳活性;菌XD 1所产表面活性剂主要积累在胞内特定的细胞器中,并在细胞壁上产生一层粘附的表面活性剂膜,膜厚140nm,在生长过程中,菌体会将细胞器和细胞壁上的表面活性剂释放到胞外.将培养72h的菌体浸入双蒸水中,6h后菌体能把积累在细胞器和细胞壁上的表面活性剂释放到水体中.     

Interfacial forces between silica surfaces measured by atomic force microscopy

Colloidal particle stability and some other interfacial phenomena are governed by interfacial force interactions. The two well known forces are van der Waals force and electrostatic force, as documented by the classical Derjaguin, Landau, Verwey, and Overbeek (DLVO) theory. Moreover, advances in modern instrumentation and colloid science suggested that some short-ranged forces or structure forces are important for relevant colloidal systems. The interfacial and/or molecular forces can be measured as a resultant force as function of separation distance by atomic force microscopy (AFM) colloid probe. This article presents a discussion on AFM colloid probe measurement of silica particle and silica wafer surfaces in solutions with some technical notifications in measurement and data convolution mechanisms. The measured forces are then analyzed and discussed based on the ‘constant charge’ and ‘constant potential’ models of DLVO theory. The di erence between the prediction of DLVO theory and the measured results indicates that there is a strong short-range structure force between the two hydrophilic surfaces, even at extremely low ionic concentration, such as Milli-Q water purity solution.     

GO-TiO2改性中空纤维膜的制备条件及抗污染性能研究

以氧化石墨烯(GO)与纳米二氧化钛(TiO_2)为改性剂,采用界面聚合法与抽滤吸附结合,对聚偏氟乙烯中空纤维超滤膜(简称原膜)进行表面改性,得到新型纳米改性膜(简称GO-TiO_2改性膜).研究改性膜的制备工艺条件及其对腐殖酸(HA)的吸附截留性能与抗污染特性.结果表明:(1)最佳制备工艺条件为:钛酸丁酯2 m L、GO 1 mg、间苯二胺1%(质量分数)、间苯二胺浸泡时间8 min、均苯三甲酰氯0.2%(质量分数)、均苯三甲酰氯浸泡时间10 min;(2)亲水性提高显著,亲水性表面为GO-聚酰胺-TiO_2复合结构,改性膜接触角由80.6°±1.8°下降到38.6°±1.2°;(3)抗污染性能提高明显.改性膜通量总衰减率由改性前的51.2%下降到35.6%,过滤周期约为原膜的2.5倍;反冲洗后膜通量恢复率由69%提高到96%.     

大气环境下风电塔筒金属材料的应力腐蚀

塔筒金属材料在大气中的应力腐蚀会导致脆性断裂,从而对产生严重的后果。本文重点论述了应力腐蚀的几种腐蚀机理以及Cl-对应力腐蚀的影响,并介绍了应用较广的慢应力速率试验方法。     

汶川地震地表变形特征

汶川地震地表变形特征丰富多彩。在震后40天自北至南对地震地表变形现象进行了为期10天的专题考察和分析,对北川、擂鼓、汉旺、蓥华、白鹿、小鱼洞、虹口和映秀等8个断裂出露部位进行了重点剖析。结果表明,不同侧面,不同级次的现象均显示出统一的变形变位图案,但具体而言它们比理论模型、规例要复杂得多。它们具体表现为:沿汶川地震断裂面推挤形成隆起,产生纵向、横向裂隙;推挤前缘冲断塌落,形成逆断型崩积楔;多方向挤压、或引张,显示同一应力作用下变形组合的复杂性。这些均不同程度地丰富了现有的应力作用理论。     

Surfactant-induced changes in gravity fingering of water through a light oil

Gravity-driven preferential flow (fingering) can greatly affect how one fluid displaces another in the subsurface. We have studied the internal properties of these preferential flow paths for water, with and without surfactants, infiltrating into oil saturated porous media using synchrotron X-rays, and miniature tensiometers to characterize fluid content and pressure relationships. We also used a light transmission technique to visualize overall flow pattern. Capillary pressure and water content decrease behind the front, similar to fingers in air-dry sand, with quantitative differences for five different surfactants with surface tensions ranging from 4–21 g/s². Using unstable flow theory, the finger widths, capillary pressure drops within the fingers, finger tip lengths, and finger splitting dynamics were scaled successfully with interfacial tension, fluid density, and the contact angle using the fingers in air–water systems as the reference.     

Improving the extraction of tetrachloroethylene from soil columns using surfactant gradient systems

In this work, we extend the recently developed gradient approach for surfactant-enhanced remediation of dense non-aqueous phase liquid (DNAPL)-impacted sites. The goal of the gradient approach is to maximize the DNAPL solubilization capacity in swollen micelles (Type I aqueous microemulsions) while at the same time minimizing the potential for DNAPL mobilization. In this work, we introduce a modified version of the capillary/trapping curve that we refer to as the gradient curve to help interpret and/or design the gradient approach. The gradient curve presents the residual DNAPL saturation as a function of interfacial tension and microemulsion viscosity. This approach demonstrates that keeping a low viscosity of the microemulsion phase is not only important for keeping a low head loss during surfactant flooding but also to prevent oil mobilization. Eight microemulsion systems were evaluated in this research; these systems were evaluated based on their tetrachloroethylene (PCE) solubilization capacity, interfacial tension (IFT), viscosity, density, and coalescence kinetics. Two of these systems were chosen for evaluation in site-specific column tests using an increasing electrolyte gradient to produce a decreasing IFT/increasing solubilization gradient system. The column studies were conducted with media from Dover Air Force Base in Dover, DE. Both solubilized and mobilized DNAPL were quantified. During the column studies, we observed that substantial PCE was mobilized when the residual level of PCE in the column was significantly higher than the steady-state residual saturation level being approach (as predicted from the gradient curve). Four column studies were performed, three of which were used to asses the validity of the gradient curve in predicting the residual saturation after each gradient step. From these tests we observed that starting IFTs of less than 1 mN/m all produced the same mobilization potential. In the last column, we used an additional gradient step with an initial IFT above 1 mN/m to dramatically reduce the amount of PCE mobilize. Based on the good agreement between column results and projections based on the gradient curve, we propose this as a preferred method for designing gradient surfactant flushing systems.