对苯二甲酸降解菌固定化生物流化床处理精对苯二甲酸废水

采用微生物筛选、纯化技术,获得了降解对苯二甲酸（TA）的YPC—TA1,YPC—TA2,YPC-TA3,YPC—TA44株菌株。将筛选出的TA降解菌固定化,处理初始TA质量浓度为2650mg／L的模拟废水,降解36h后TA去除率达100％。用TA降解芮在生物流化床反应器中处理PTA废水,最佳容积负荷为6.7kg／（m^3·d）。生物流化床反应器可在容积负荷为6．0～6．5kg／（m^3·d）的较佳条件下长周期稳定运行,COD去除率保持在91％左右,TA去除率保持在94％左右。低pH废水冲击和高容积负荷废水冲击时COD,TA去除率均明显下降,恢复正常讲水后3～4d,COD,TA去除率均恢复正常。     

MBBR处理制药废水的试验研究

采用二级移动床生物膜反应器(MBBR)处理呋喃铵盐制药废水。在填充比为40%,总水力停留时间为32h时,COD的去除率为88.6%,TN的去除率为25.7%,第二级反应器对NH3-N的去除率为56.2%。     

超重力技术治理火炸药行业氮氧化物的初步研究

火炸药行业排放氮氧化物(NOX)具有浓度高、排放点不集中和间歇排放的特点,采用超重力技术对尾气中高浓度的NOX进行湿法吸收.以清水为吸收剂,研究了进气量、液气比和超重力因子等因素对NOX吸收率的影响.结果表明,单级NOX吸收率可达64.69%(β＝90).超重力旋转填料床具有占地面积小、投资低和操作方便等优点,适宜于火炸药行业吸收NOX.     

铁炭微电解深度处理焦化废水的研究

采用曝气铁炭微电解工艺对焦化废水进行了深度处理.结果表明,在活性炭、铁屑和NaCl投加量分别为10 g/L、30 g/L和200 mg/L的条件下反应240 min,出水COD去除率在30%～40%;酸性条件可以进一步提高COD去除率;微电解可以去除原生化出水中的难降解有机物,出水物质的分子量主要集中于2000 Da以下,以脂类和烃类化合物为主;出水的可生化性有了大幅度提高,BOD5/COD由0.08增加到0.53.实验结果表明,铁炭微电解是深度处理焦化废水的一种有效工艺.     

低COD浓度废水启动EGSB反应器

以厌氧活性污泥和好氧活性污泥接种于2个膨胀颗粒污泥床(EGSB)反应器中,进水流量为10 mL/min,回流量为180 mL/min,进水COD浓度在180 mg/L左右,有机负荷率(OLR)为1.728 kg COD/m3·d左右,污泥负荷率(SLR)为0.19 kg COD/kg MLSS·d左右,出水COD浓度维持在40mg/L左右,COD去除率达80%以上.控制温度在32～35 ℃,pH在6.8～7.2,反应器内氧化还原电位在-340 mV以下,水力停留时间(HRT)4.2 h,上升流速4.86 m/h以及加入80 mg/L絮凝剂(硫酸铝钾),缩短了启动时间,促进了颗粒污泥的形成.分别经过60 d和120 d运行,反应器启动成功.结果表明,上升流速、絮凝剂和污泥类型对颗粒污泥的形成有影响;接种好氧活性污泥在低浓度COD下,合理控制负荷速率能成功启动EGSB反应器.     

MBBR与A/O法对污水中有机物及氮处理效果的研究

实验在不同水力停留时间（HRT）、进水COD浓度和不同COD容积负荷条件下考察了移动床生物膜反应器（MBBR）和活性污泥A/O工艺对污水中有机物及氮的处理效果。结果表明,MBBR工艺去除有机物和脱氮效果均优于A/O工艺。在进水COD和NH₃－N浓度分别为1000和25 mg/L,HRT为8 h时,MBBR的COD和TN去除率分别为92％和94％,而A/O工艺分别为78％和82％。造成这种结果的原因是MBBR的生物活性高,并且在生物膜内发生了同时硝化反硝化。MBBR脱氮能力受COD冲击明显小于A/O,但在较低进水COD浓度下,两者TN去除率均较低。     

维生素B1制药废水的铁炭微电解-混凝预处理工艺

针对维生素B1制药废水高有机物浓度、高悬浮物、色度高、难降解的特点,采用铁炭微电解-混凝工艺对其进行预处理,效果良好。铁炭微电解-混凝工艺的最佳运行条件为:进水pH值为4,铁炭比为1∶1,曝气量为0.2m3/h的情况下停留时间80min。出水CODCr浓度平均为1600mg/L,去除率约为79%,色度去除率为85%,出水达到了(GB8978-1996)二级排放标准。     

多孔球三相流化床冷态试验的研究

对多孔球为填料的三相流化床进行冷态试验研究,研究不同工况下气体空塔流速、填料静止高度、喷淋密度等因素对流化床阻力特性和脱硫效率的影响.试验表明,用多孔球替代空心球做填料,不仅可以消除空心球在流化过程中出现的问题,还可以适当提高脱硫效率.     

聚硅酸铝铁/羧基壳聚糖复合絮凝剂处理硫化黑染料废水的研究

用聚硅酸铝铁/羧基壳聚糖复合絮凝剂对硫化黑染料废水进行了处理,研究了影响絮凝剂处理硫化黑染料废水的影响因素。结果表明,较佳的条件为转速50 r/min、聚硅酸铝铁和羧基壳聚糖的质量配比为3、废水pH值为9.0、絮凝剂用量为60 mg/L。在该条件下,复合絮凝剂对硫化黑染料废水的COD、色度、浊度去除率分别为92.1%,88.6%,96.3%。     

Emergency shutdown of fluidized bed reaction systems

With several industrial applications of fluidized bed technology recently commercialized worldwide, it becomes essential to develop safe operation methods for fluidized bed reaction systems (FBRSs) to prevent any influence on their process values, which lead to accidents. To preventing any disaster or malfunction in an FBRS, an emergency shutdown system (ESD) is initiated, closing the reaction system in case of any abnormality by effectively isolating the flammable gas. However, an ESD is also prone to the “inactivation problem,” in which in the case of failure it initiates the emergency shutdown, even when the operating conditions of the reaction system are abnormal. It is also vulnerable to a “malfunction problem,” where the emergency shutdown is performed even when the operating conditions of the reaction system are normal. In this study, these problems were solved by investigating a reaction system through the monitoring of appropriate parameters and setting up of trigger levels, which reflect the uniqueness of an FBRS using an ESD. The parameters were identified by analyzing the scenario leading to an accident. The trigger levels were determined as the points at which the loss is smaller in the presence of an ESD, as compared to the value of the loss function in the presence or absence of an ESD. Furthermore, the ESD design model was applied as a case study in the ammoxidation process of propylene. The results showed that an ESD can prevent an approximately 8 billion yen of loss due to accidents in plant operations, against an investment of 200 million yen.