泗河水环境容量及最大允许排污量计算

规范了水环境容量的定义和分类,建立了符合泗河水文、水资源特征和水环境状况的河流水环境容量模型,与GIS技术结合构建了适合北方地区的河流水环境容量计算程序和方法;摸清了水功能区-入河排污口-点源排放口的一一对应关系,提出了将水域环境容量转换为陆域点源最大允许排污量的估算方法。计算了泗河在满足水功能区划条件下的水环境容量及最大允许排污量,从而为制定该河流水污染物容量总量控制方案提供了科学依据。     

我国水源污染事故风险点定量识别方法

水源事故的频发会对城市供水系统产生威胁,有必要针对供水系统风险进行评估和防控。针对水源事故频发及高发因素定量甄别研究,筛选统计了国内近20年来1 900多起水质突发事故案例,梳理了触发水源水质污染的多种因素,通过构建水源水质安全事故树和贝叶斯网络进行了相互验证分析。结果表明：我国水源污染事故主要因素贡献为依次突然排放(0.466)、污染长期累积(0.242)、交通事故(0.109)等;采用贝叶斯网络计算进行验证,其结果与事故树方法一致性较好。该方法有助于水源污染防控工作中风险点甄别和排序,可为我国饮用水安全保障水平的提升提供支撑。     

2010—2019年成都市机动车排污特征分析及防控措施减排效果评估

为评估2010—2019年成都市机动车防控措施的减排效果,以2010年为基准年,采用排放清单法计算了各减排措施下2019年的减排量,对比分析了4种控制措施的减排效益。结果表明：成都市机动车排污总量逐年下降,2019年PM_2.5、NO_x、VOCs、CO、SO₂和NH₃的排放量分别为0.27×10⁴、4.63×10⁴、1.70×10⁴、28.99×10⁴、0.21×10⁴和0.45×10⁴ t,主要分布在中心城区,其中重型货车对PM_2.5和NO_x贡献最大,小型客车对VOCs、CO、SO₂和NH₃贡献最大;措施中加严标准的综合减排量最大,重点减排车型为小型客车、轻型货车、公交车等,2019年6种污染物减排量分别为0.14×10⁴、2.27×10⁴、1.29×10⁴、6.77×10⁴、0.07×10⁴和0.38×10⁴ t;优化城市交通管理对小型客车和摩托车的减排效果显著,2019年6种污染物减排量分别为0.04×10⁴、0.81×10⁴、0.38×10⁴、2.55×10⁴、0.05×10⁴和0.04×10⁴ t;淘汰高排放车辆对小型客车、轻型货车等的减排较明显,2019年6种污染物减排放量分别为0.13×10⁴、0.98×10⁴、0.34×10⁴、2.62×10⁴、0.01×10⁴和0.007×10⁴ t;推广清洁能源汽车的重点减排车型为出租车和公交车,虽然可有效减少PM_2.5、NO_x的排放,但VOCs却有小幅增加,2019年6种污染物减排放量分别为0.12×10⁴、0.62×10⁴、−0.13×10⁴、0.30×10⁴、0.004×10⁴和0.000 5×10⁴ t。     

不同强度岩石中开挖圆形巷道的局部化过程模拟

利用FLAC模拟了不同粘聚力条件下圆形巷道的局部化过程。为了模拟巷道开挖,利用编写的F ISH函数删除巷道内部的单元。岩石服从莫尔库仑剪破坏与拉破坏复合的破坏准则,破坏之后呈现应变软化-理想塑性行为。文中模拟分为3步:首先,将静水压力施加在模型上,直到达到静力平衡状态;然后,利用编写的F ISH函数开挖巷道;最后,计算重新开始,直到达到静力平衡状态或者塑性流动状态。模拟结果表明,随着粘聚力的降低,巷道围岩的破坏模式首先由孔壁附近零星单元的破坏向4个对称的小V形坑式剪切破坏转变,然后由包含若干小V形坑的大V形坑式剪切破坏向巷道全断面的破坏转变。前三者破坏发生后,巷道围岩仍然能保持稳定。与最大塑性拉伸应变相比,最大剪切应变增量、最大塑性剪切应变要高得多;最大剪切应变增量、最大塑性剪切应变相差不大;随着粘聚力的增加,三者均越来越小。     

原状黄土的反压饱和法试验研究

含水量是黄土液化特性研究中的一个至关重要的参数,对原状黄土进行充分饱和是饱和黄土动三轴试验中一个不可回避的课题。以WF公司生产的WF12440型空心圆柱扭剪仪为实验平台,运用反压饱和法,对室内原状黄土进行了饱和试验研究。该仪器提供3种不同加压方式增加围压和反压(孔压),即手动加压、自动加压和线性持续加压,通过检测孔隙压力系数B值是否达到0.95以上来判断黄土是否完全饱和。试验表明,即便是初始饱和度较低的原状黄土,也可以采用反压饱和法,在较短的时间内使孔压系数B值达到0.95以上,实现完全饱和,具体可以采用线性连续加压方式;初始压力差,即围压和反压之差一般可设为10 kPa,起始围压也设为10 kPa,太大或太小都会对试样造成破坏;如果孔压在1分钟内的变化值小于围压和反压之间压力差的5%,则认为孔压稳定,即可进行B值检测。     

实行年度目标考核是促进监测工作发展的有效方法

实行年度目标责任制考核 ,为监测站的改革和发展找到了一条有效途径。文章通过对年度目标考核责任制的方式、方法及实施后所取得成效的介绍 ,为监测站的改革与发展提供了借鉴     

Predicting bicycle helmet wearing intentions and behavior among adolescents

INTRODUCTION: Cycling accidents in Australia, especially those resulting in head injuries, are a substantive cause of death and disability; but despite legislation and evidence that helmets reduce the risk of head injury, few adolescents wear them. METHOD: This study employed a revised version of the Theory of Planned Behavior (TPB; [Ajzen, I. (1991). The theory of planned behavior. Organizational Behavior and Human Decision Processes, 50, 179-211]) to investigate the determinants of helmet use among a sample of adolescents. Participants in the initial data collection were 294 high school students in Year 8 and Year 11, with 266 completing a follow-up questionnaire measuring behavior over the previous two weeks. RESULTS: Social norms, perceptions of control, and past behavior significantly predicted intentions to use helmets and perceptions of control and past behavior predicted actual helmet use. CONCLUSIONS: Strengthening the routine of helmet use and building young people's confidence that they can overcome any perceived barriers to helmet use will improve adherence to helmet wearing behavior.     

Exploring the dark side of organizational citizenship behavior

In recent years, there has been increasing interest in positive organizational scholarship in general, including positive organizational behavior (POB) in particular. This work identifies organizational citizenship behavior (OCB) as a prototypical POB. Conceptualizing OCBs in this way is sensible in light of more than 30 years of research highlighting the desirable aspects of such behavior. At the same time, some researchers have raised questions about positive organizational scholarship and have called for a more balanced view of ostensibly positive behaviors. The purpose of this paper, then, is to take a more nuanced view of OCBs while highlighting the dark side of citizenship behavior. In doing so, we review conceptual and empirical work that has challenged the idea that OCBs are inherently positive. We also discuss research that seeks to develop a deeper understanding of the conditions under which OCB does more harm than good. Finally, important areas for future research and the practical realities facing scholars who seek to publish research investigating the dark side of citizenship are addressed as well. Copyright © 2012 John Wiley & Sons, Ltd.     

Force-Velocity Characteristics of Individual Human Skeletal Muscles: TBCIat and TBCIong. Outline of the Method

The aim of the work is to outline a procedure of finding force-velocity (F–V) characteristics (F = f(V)) of individual skeletal muscles of the human locomotor system. The presentation is based on an example concerning extensors of the elbow joint: the lateral and long heads of triceps brachii (TBCIat and TBCIong). The experimental part of the procedure involves a natural movement of using the upper extremity to push an external object of variable, adjustable load, engaging both the elbow and shoulder joint.

Five men aged 23 took part in the experiment. Their task was to push the handle of a physical pendulum whose moment of inertia could be adjusted within the range of 58 kg m²-450 kg m², so as to give it maximum angular velocity. During each trial the movement of the trunk, of the upper extremity and of the pendulum was video recorded and the force applied with the hand to the handle of the pendulum was measured.

In order to find the F–V characteristics a simulation model SHOULDER was used, which is capable of solving the synergy problem for muscles of the arm and the shoulder girdle.

It was found that despite considerable dispersion of experimental points the respective regression lines revealed a clear tendency of decreasing muscle force for increased shortening velocity of the monoarticular head (TBCIat) and of increasing muscle force for increased lengthening velocity of the biarticular head (TBCIong) of the triceps brachii muscle.     

Effect of Sweating on Insulation of Footwear

The study aimed to find out the influence of sweating on footwear insulation with a thermal foot model. Simultaneously, the influence of applied weight (35 kg), sock, and steel toe cap were studied. Water to 3 sweat glands was supplied with a pump at the rate of 10 g/hr in total. Four models of boots with steel toe caps were tested. The same models were manufactured also without steel toe. Sweating reduced footwear insulation 19–25% (30–37% in toes). During static conditions, only a minimal amount of sweat evaporated from boots. Weight affected sole insulation: Reduction depended on compressibility of sole material. The influence of steel toe varied with insulation. The method of thermal foot model appears to be a practical tool for footwear evaluation.