Combustion characteristics of Malaysian municipal solid waste and predictions of air flow in a rotary kiln incinerator

Malaysia is in dire need of alternatives to landfilling for solid waste management. Recently, landfills have faced the problems of overfilling, overflowing of leachates leading to pollution of water resources, and uncontrolled dust emissions adversely affecting the local environment. With the rising cost of urbanization coupled with the high rate of waste generation, one possible method of waste treatment that is receiving particular attention by the government is incineration. Incineration of solid waste is rather new in Malaysia, with limited usage in handling small sources of waste generation such as the municipal solid waste (MSW) of resort islands; however, its potential in ameliorating the problems associated with solid waste treatment may make it an attractive alternative to landfill. This article presents the results of test runs conducted to investigate the performance of a locally designed and manufactured rotary kiln incinerator (RKI). The test runs were conducted using MSW collected from the Shah Alam municipality. The combustion efficiency was analyzed by looking at the temperature profiles and chemical species concentrations. To complement the combustion characteristics measurements, predictions of the air flow in the incinerator during the process were also investigated. The overall performance of the RKI suggests that it is suitable for treating MSW.     

Occurrence of phenols in leachates from municipal solid waste landfill sites in Japan

The concentrations of 41 phenols in leachates from 38 municipal solid waste (MSW) landfill sites in Japan were measured. The main phenols detected in leachates were phenol, three cresols, 4-tert-butylphenol, 4-tertoctylphenol, 4-nonylphenol, bisphenol A, and some chlorophenols. The concentration levels of phenols were affected by the pH values of the leachates and the different types of landfill waste. The origins of phenol and p-cresol were considered to be incineration residues, and the major origin of 4-tert-butylphenol, bisphenol A, and 2,4,6-trichlorophenol was considered to be solidified fly ash. In contrast, the major origins of 4-tert-octylphenol and 4-nonylphenol were considered to be incombustibles. The discharge of leachates to the environment around MSW landfill sites without water treatment facilities can cause environmental pollution by phenols. In particular, the disposal of incineration residues including solidified fly ash and the codisposal of solidified fly ash and incombustibles might raise the possibility of environmental pollution. Moreover, the discharge of leachates at pH values of 9.8 or more could pollute the water environment with phenol. However, phenol, 4-nonylphenol, and bisphenol A can be removed to below the con centration levels that impact the environment around landfill sites by a series of conventional water treatment processes.     

废旧电池资源化、无害化

对当前国内外在废旧电池的处理处置方面进行了综合性论述,对废旧电池的危害及当前应采取的对策进行分析。     

利用餐饮业废油脂制造生物柴油

世界的石油产量将会逐渐减少,石化柴油燃烧后所排放的废气是造成的城市空气污染的主要原因,生物柴油是石化柴油很好的替代能源,文章介绍了国外废油脂处理利用和甸餐饮业废油脂的概况,提出了利用餐饮业废油脂制造生物柴油的方法和工艺流程,并讨论了利用餐饮业废油脂制造生物柴油的几个问题。     

Metal concentrations in used engine oils: Relevance to site assessments of soils

Used engine oils contain metals, which upon entering soils may pose risks to human health or the environment. In this study, previously published concentrations of 23 metals in 213 used engine oil samples from the early 1970s to the mid-1990s are statistically evaluated. Neat (100%) used engine oils were found to contain relatively high concentrations of lead, calcium, and zinc, attributable to piston blow-by of leaded gasoline, calcium salt detergent additives, and zinc-bearing anti-corrosion/anti-oxidation additives, respectively. Wear metal concentrations were lower. The lead concentration in used engine oils in the U.S. declined between the 1970s and early 1990s, potentially providing a basis to constrain the “age” of used engine oil(s) in soils. The concentrations of 23 metals in used engine oils were compared to soil risk benchmarks in 15 representative jurisdictions in the U.S., Canada, Australia, and Europe. The maximum concentrations in neat (100%) used engine oil of eight metals – Be, Co, Fe, Mn, Ni, Se, Ag, and Ti – were lower than their collective minimum benchmarks in soils for the jurisdictions surveyed, indicating their concentrations in soils could not be reasonably expected to exceed any soil benchmarks. Nine metals (As, Ba, Cd, Cr, Cu, Pb, Sn, V and Zn), but particularly arsenic, cadmium, lead, tin, and zinc, were identified as potential contaminants of concern (PCOC) for soils from locations impacted with used engine oils, owing to their higher median concentrations (i.e., 2.5, 1.4, 1038, 5.0, and 922 mg/kg in oil, respectively) relative to most soil benchmarks. Site-specific benchmarks and metal concentrations at reasonable oil in soil concentrations require consideration when developing the suite of PCOC metal analytes for conducting site assessments of soils impacted by used engine oil.     

有机废气中VOC的回收方法

介绍了炭吸附法、冷凝法和膜分离法回胥机废报中ＶＯＤ的原理、工艺流程和工业应用情况，并对这些方法进行了比较，指出了适用范围。     

Producing biodiesel from waste animal oil by modified ZnO

Biodiesel produced by transesterification of waste animal oil is a promising green fuel in the future. ZnO-Al₂O₃ and ZnO/Zn₂Al composition oxides were prepared by co-precipitation method and impregnation method, respectively. The above catalysts were characterized by X-ray diffraction (XRD), Brunauer--Emmett--Teller (BET) and CO₂ adsorption and temperature-programmed desorption (CO₂-TPD) and show that the high activity for the catalyst is attributed to its high alkalinity. The reaction parameters were optimized and the results show that the transesterification ratio of waste animal oil can reach 98.7% with 10% ZnO/Zn₂Al catalyst after 2 h. Moreover, 10%ZnO/Zn₂Al compound oxides can be active for the successive cycles. The glycerol as a predominant by-product after transesterification is of high purity with high use value.     

城市生活垃圾处理方式生命周期评价的比较研究

生命周期评价理论与方法作为一种量化环境影响的工具,在诸多领域中得到了广泛的应用。在垃圾处理领域,生命周期评价最早在20世纪90年代得到应用。生命周期评价与城市生活垃圾处理的有效结合,将促进城市生活垃圾的减量化、资源化、无害化目标的实现。总结了生命周期评价理论与方法在城市生活垃圾处理中的应用现状。对国内不同城市生活垃圾处理方式环境影响因子进行比较分析,诸如全球变暖潜力、酸化潜力和富营养化潜力等因子。针对其目标范围定义、数据收集、评价方法的选择、结果解释及工艺改进等方面指出了目前研究的局限性和不足。并对未来城市生活垃圾处理生命周期评价的发展方向进行展望。     

餐厨垃圾高温厌氧消化产沼气的试验研究

探究了温度、含固率、pH及接种率对餐厨垃圾厌氧消化产沼量的影响,并设计L9(34)正交试验进行厌氧发酵工艺优化研究。结果表明,在温度为55℃、含固率为8%(质量分数)、pH为7.00、接种率为90%(质量分数)时,厌氧发酵累积产沼量为809.0mL/g(以挥发性固体计);各影响因素对产沼量的影响大小为温度pH接种率含固率。     

生活垃圾催化热解液体产物特性

为探索生活垃圾催化热解液体产物特性变化规律,选取Na2CO3、CaO、Fe2O33种催化剂,利用固定床实验、红外分析(FT-IR)进行生活垃圾热解液体产物产率和组分特性研究.结果表明,热解终温600℃无催化剂时,生活垃圾热解液产率为39.80 wt％,添加3种催化剂后热解液产率均降低;生活垃圾分别添加1％的Na2CO3和CaO后,热解油氧含量由22.49％分别降低到20.12％和18.53％,低位热值由30.30 MJ/kg分别提高到33.79和32.74 MJ/kg;无催化剂时热解油成分为脂肪类、含氧化合物及少量芳香类混合物,加催化剂后热解油中芳香类物质峰面积比例显著增加,而含氧化合物峰面积比例降低,羟基类及羧酸类含氧化合物峰面积比例明显减少,其他含氧物峰面积比例却增加;CaO催化效果较明显,生活垃圾添加1％的CaO热解油中芳香类物质峰面积比例从4.36％增加到29.46％,含氧化合物峰面积比例由49.42％降低到23.12％,其中羟基类和羧酸类化合物峰面积比例分别由34.03％和10.65％降低到0.00％和3.34％,其他含氧化合物峰面积比例由4.73％增加到19.77％.