基于TiO2载体的锰铈系低温SCR脱硝催化剂研究进展

开发低温、高活性、高抗硫抗水性能的选择性催化还原(SCR)脱硝催化剂已成为国内外的研究热点。综述了基于TiO2载体的锰铈系低温脱硝催化剂的脱硝性能,探讨了助剂掺杂改性、制备方法、反应条件等对催化剂脱硝性能的影响,总结了现有低温脱硝催化剂的技术难点,指出SCR催化剂的研究需要着重考虑以下几方面:深入研究催化剂的反应机理和中毒机理;研究催化剂的循环再生;探究拓宽催化剂温度窗口,使其适应不同的温度条件。     

中国低碳城市试点的政策设计逻辑

政策试点是中国国家治理策略体系的重要组成部分,是中国政府遵循“由点到面”逻辑以试验手段制定政策的一种常规性工作方法。低碳城市试点是中国应对气候变化战略的重要组成部分,通过选择不同类型、不同发展阶段、不同资源禀赋的地区开展试点,探索经济增长与碳排放脱钩的模式。现有文献侧重低碳城市建设的内涵、建设模式与路径、温室气体的核算方法、政策手段、峰值研究与达峰路径、效果评估等,有力地支持了低碳城市建设决策,但对于低碳城市试点的政策设计鲜有涉及。本文从政策过程理论、央地关系两个视角,结合府际学习与竞争关系,建构了中国低碳城市政策“试点–扩散”机制与政府行为的分析框架。中国的低碳城市试点具有探索型开拓性、综合型专业性、授权型自主性的特点,结合三批低碳城市试点的文件要求和实践进展,从政策试点的选点、设计、执行、监督和评估五个方面对于中国低碳城市试点进行了系统的梳理分析。相较于经济领域的其他政策试点,低碳城市政策试点具有弱激励弱约束的政策环境。地方政府基于自身的学习能力和领导力,在政策创新方面表现出争先、自主、效仿和守成四种行为特征,并以杭州、深圳、镇江、成都四个表率城市做了实证。政策“试点-扩散”的过程从本质上讲是中国政策创新与扩散的过程,可能在现实中需要往复多次进行,中国已陆续开展的三批低碳城市试点工作就遵循这样的政策逻辑。试点的意义是试出问题、解决问题、积累经验。从前三批试点城市评估结果来看,试点城市在低碳发展目标设定、转型路径探索和低碳发展动力转换等方面与社会的预期仍有差距,为此本文提出了推进低碳城市建设的四点建议:一是激发城市低碳发展的内生动力;二是完善低碳城市试点的科学论证机制;三是建立激励与约束并举的长效机制;四是强化市场公平竞争的政策导向。     

氧化还原体系低温引发丙烯酸酯乳液聚合安全风险研究

以甲基丙烯酸甲酯、丙烯酸酯乙酯、丙烯酸酯丁酯为反应单体,十二烷基苯磺酸钠为乳化剂,过硫酸铵为氧化剂,亚硫酸氢钠为还原剂,在低温下进行乳液聚合。主要研究了反应单体的热稳定性及反应过程中的相关热力学参数,最后按照规定对该聚合体系进行了安全风险研究。研究结果表明,丙烯酸酯混合单体无热分解放热风险,丙烯酸酯乳液体系的绝热温升(△Tad)为49.6℃,失控体系能达到的最高温度(MTSR)为91.9℃,该体系的最终反应工艺危险度评估为1级,聚合工艺热风险低。     

某矿低铜废石综合回收利用项目职业病危害预评价

为了对某矿业有限公司低铜废石综合回收利用项目可能产生的职业病危害因素进行辨识、分析和评价,采用检查表、类比法相结合的原则对该项目的铲装、破碎、运输、筑堆等工艺进行分析评价,并利用经验法对浸出、萃取电积工艺进行分析评价。结果表明:类比工程中绝大部分粉尘、噪声检测点的浓（强）度符合国家标准;化学毒物、工频电场接触浓（强）度符合国家标准;电积车间的通风满足要求;萃取车间的事故通风能力不足。评价方法及通风计算方法对同类项目具有借鉴意义。     

国内外低碳产业园发展模式研究

通过分析国内外6个典型低碳产业园案例,归纳总结出再生利用型、清洁生产型、产业耦合型3种类型低碳产业园,横向对比分析3种类型低碳产业园的特点,纵向对比分析国内外低碳产业园的特色,在此基础上提出3种类型低碳产业园的发展模式。     

气象条件对静电除尘器低温腐蚀的影响分析

在已建成投产的静电除尘器当中,低温腐蚀是严重影响除尘器使用寿命的因素之一。以某烧结厂静电除尘器为研究对象,利用CFD软件,采用标准k-ε湍流模型对除尘器内部流场及温度场的分布进行数值模拟研究,得到静电除尘器内部流场和温度场分布特征,分析这些数据可知除尘器温度最低部位位于灰斗处,外界气温对壳体温度具有正相关的影响,在此基础之上有针对性地提出对静电除尘器壳体低温腐蚀的防治措施。     

钢铁企业大型低位料仓汽车卸料的粉尘控制

某钢企大型低位料仓为汽车卸料,料仓厂房内空高,跨度大,料仓上部贯通,物料落差大,卸料中产生大量粉尘,环境污染问题典型突出。通过对低位料仓汽车卸料产尘特性分析,采取加强生产管理、组织汽车有序卸料、料仓厂房有效密闭、合理设计捕尘方式和布袋除尘系统等措施,能够有效地控制粉尘污染。除尘系统具有投资及运行费用少,除尘效果明显的优点。     

Autonomous emergency braking systems adapted to snowy road conditions improve drivers' perceived safety and trust

Objective: This study investigated drivers' evaluation of a conventional autonomous emergency braking (AEB) system on high and reduced tire–road friction and compared these results to those of an AEB system adaptive to the reduced tire–road friction by earlier braking. Current automated systems such as the AEB do not adapt the vehicle control strategy to the road friction; for example, on snowy roads. Because winter precipitation is associated with a 19% increase in traffic crashes and a 13% increase in injuries compared to dry conditions, the potential of conventional AEB to prevent collisions could be significantly improved by including friction in the control algorithm. Whereas adaption is not legally required for a conventional AEB system, higher automated functions will have to adapt to the current tire–road friction because human drivers will not be required to monitor the driving environment at all times. For automated driving functions to be used, high levels of perceived safety and trust of occupants have to be reached with new systems. The application case of an AEB is used to investigate drivers' evaluation depending on the road condition in order to gain knowledge for the design of future driving functions.

Methods: In a driving simulator, the conventional, nonadaptive AEB was evaluated on dry roads with high friction (μ = 1) and on snowy roads with reduced friction (μ = 0.3). In addition, an AEB system adapted to road friction was designed for this study and compared with the conventional AEB on snowy roads with reduced friction. Ninety-six drivers (48 males, 48 females) assigned to 5 age groups (20–29, 30–39, 40–49, 50–59, and 60–75 years) drove with AEB in the simulator. The drivers observed and evaluated the AEB's braking actions in response to an imminent rear-end collision at an intersection.

Results: The results show that drivers' safety and trust in the conventional AEB were significantly lower on snowy roads, and the nonadaptive autonomous braking strategy was considered less appropriate on snowy roads compared to dry roads. As expected, the adaptive AEB braking strategy was considered more appropriate for snowy roads than the nonadaptive strategy. In conditions of reduced friction, drivers' subjective safety and trust were significantly improved when driving with the adaptive AEB compared to the conventional AEB. Women felt less safe than men when AEB was braking. Differences between age groups were not of statistical significance.

Conclusions: Drivers notice the adaptation of the autonomous braking strategy on snowy roads with reduced friction. On snowy roads, they feel safer and trust the adaptive system more than the nonadaptive automation.     

燃煤电厂超低排放气态污染物监测技术综述

介绍了燃煤电厂超低排放气态污染物监测系统的采样系统和分析单元,分析了其各自的优缺点。对稀释抽取式、冷干抽取式和热湿抽取式3种采样方法,以及非分散红外吸收法(NDIR)、非分散紫外吸收法(NDUV)、紫外差分吸收法(DOAS)、紫外荧光法(UVF)和化学发光法(CL)5种分析方法进行对比。结果表明,冷干抽取式+紫外差分法以及稀释抽取式+紫外荧光法+化学发光法可以较好地符合燃煤电厂超低排放监测的要求。     

Double Green Process: a low environmental impact method for recycling of CdTe,a-Si and CIS/CIGS thin-film photovoltaic modules

On the basis of the method for managing the end of life of CdTe photovoltaic panels previously proposed by the authors, a new method for the recycling of all types of thin-film panels (CdTe, a-Si and CIS/CIGS) has been developed and optimised under a research project founded by Enel Foundation and CRUI Foundation. The DGP process has been developed through a feasibility study carried out from three points of view: technical, environmental and economic. The process is composed by two sub-processes matched to each other, one suitable for CdTe panels (named DGPa) and the other one for a-Si and CIS/CIGS panels (DGPb). The Double Green Panel process is based mainly on mechanical treatments with a minimum use of chemicals and it is characterised by a greater level of automation and a high flexibility in production capacity. The potential environmental impacts of various configurations of the DGP process have been extensively analysed with LCA tool in order to develop an environmentally friendly process. The economic feasibility has been assessed through the Discounted Cash Flow Analysis (DCFA) method. The revenues associated to the recovery of valuable and common materials and the recycling costs have been taken into account.