辽河流域水环境压力及污染治理模式研究

系统分析了辽河流域近十年社会经济和水污染物排放之间的关系,基于污染物排放强度和人均GDP指标,建立辽河流域COD和氨氮环境学习曲线;结合情景分析法预测在现有治污水平下,辽河流域未来水污染物排放趋势及水环境压力。结果表明,辽河流域水环境压力巨大。根据辽河流域污染治理中存在的实际问题,提出新时期的污染治理模式。     

Application of CGP-cross route process for microstructure refinement and mechanical properties improvement in steel sheets

A modified method of severe plastic deformation (SPD) entitled constrained groove pressing-cross route (CGP-CR) was introduced for imposing a high magnitude of equivalent strain of about 2.32 per pass on the sheet form samples. The major benefit of this improved route compared to previous common route was the more homogeneity of strain in the rolling (RD) and transverse (TD) directions of sheets. In this study, low carbon steel samples were used for examination of evolutions in microstructure and mechanical properties during SPD via CGP-CR process. Mechanical properties improvement were measured by tensile and macro hardness tests. The results indicate that CGP-CR process can effectively improve tensile strength; and also, yield stress and hardness of as-received low carbon steel samples were improved up to about 100% after two deformation passes. Also, high magnitude of inhomogeneity can be observed in hardness distribution through first pass of the process which diminishes in the subsequent passes. Microstructural evolutions during process were monitored by optical microscopy observations and X-ray diffraction analysis. The results demonstrate that initial ferritic microstructure with grain size of about 30 μm was refined to a 225 nm cell structure after two passes of CGP-CR process.     

Modulation-assisted high speed machining of compacted graphite iron (CGI)

The application of controlled, low-frequency modulation (～100 Hz) superimposed onto the cutting process in the feed-direction – modulation-assisted machining (MAM) – is shown to be quite effective in reducing the wear of cubic boron nitride (CBN) tools when machining compacted graphite iron (CGI) at high machining speeds (>500 m/min). The tool life is at least 20 times greater than in conventional machining. This significant reduction in wear is a consequence of the multiple effects realized by MAM, including periodic disruption of the tool–workpiece contact, formation of discrete chips, enhanced fluid action and lower cutting temperatures. The propensity for thermochemical wear of CBN, the principal wear mode at high speeds in CGI machining, is thus reduced. The tool wear in MAM is also found to be smaller at the higher cutting speeds (730 m/min) tested. The feed-direction MAM appears feasible for implementation in industrial machining applications involving high speeds.     

非均相类Fenton试剂的制备及其在焦化废水处理中的应用研究

利用浸渍法,将Fe3＋负载在经酸碱改性后的粉状活性炭上,当浸渍液浓度为2．5％,固化温度为270℃时,制成的催化剂催化活性较高。用自制的非均相类benton试剂降解焦化废水,通过正交试验和极差分析得出,影响因素的主次顺序为催化剂用量〉初始pH值〉反应时间〉H：0：投加量。结果表明,在100ml水样中。室温条件下,初始pH值为4．0,催化剂使用量为1．5g,H20：投加量为5ml（分两次投加）,反应时间为90min时,COD去除率可达99％。采用混凝＋化学沉淀＋非均相类Fenton试剂法处理焦化废水,各主要出水水质指标为：色度lO倍;COD浓度38．5mg／L;氨氮浓度8．4mg／L,达到国家一级排放标准。     

污泥减量化技术研究进展与发展趋势

污泥的处理与处置已成为国内外污水处理厂的沉重负担,污泥减量成为解决此问题的重要途径。针对污泥处理处置过程中的环境问题和经济效益,在隐性生长、代谢解偶联、微型动物捕食作用等方面阐述了在水处理方面污泥减量化技术的研究进展,综述了污泥减量技术的研究应用现状,同时探讨了各技术存在的问题及其重点发展方向。     

还原法修复六价铬污染土壤的研究

摘要：铬渣中含有毒性较强的六价铬化合物,其严重污染环境。本文通过实验室模拟试验,研究了硫代硫酸钠、亚硫酸钠、抗坏血酸和硫酸亚铁等还原剂对铬渣污染土壤中六价铬的解毒效果。探讨了还原剂的浓度、pH和反应时间对六价铬还原效果的影响。结果表明：亚硫酸钠浓度为1mol／L、pH9．5和反应时间为15min时对六价铬的还原效果最佳。