长江河口硅和磷生源要素质量浓度的变化特征

根据近年来长江河口区域内大通水文站的记录和近期在长江入海河口区上海段多个采样点的生源要素质量浓度实测数据,比较水中可溶性硅酸盐和磷酸盐的质量浓度,分析在长江入海河口区水中硅和磷元素含量的主要变化特征.结果表明,长江水中的硅酸盐和磷酸盐从长江入海河口进入大海的过程中,其质量浓度有降低的趋势,它们在长江入海河口的多年的质量浓度变化趋势是相反的.长江入海河口区域上游的磷酸盐质量浓度升高幅度较大,而硅酸盐变化不大,硅酸盐、磷酸盐质量浓度在长江河口区进入海洋的过程中迅速降低.      

土壤渗滤处理系统运行控制的模拟研究

通过建立地下水数学模型,回答了土壤渗滤工程运行控制中的两个难点问题:(1)工程运行水力负荷.当工程地块周边存在河流时,河流水位低时,有助于增加水力负荷,反之则降低水力负荷;实际土壤运行面积的增加和独立运行单元之间的间距增加也能够增加工程运行水力负荷.(2)地下水水质监测井的优化布设.模拟工程运行后地下水水质空间分布特征,在地下水水质最不利的位置和其他特别关注的位置布置监测井,从而能够以具有典型代表性且数目较少的监测井达到准确评估工程对地下水水质影响的目的.     

Mass transport model of ions within biofilms under the effect of external field

A mass transport model was developed to predict the transport rate of ions within biofilms, which was experimentally verified using the fluxes of NH4^＋ and Ca^2＋ through the heterotrophic biofilms with the thickness varying from 230 to 1430μm under the effect of external field in the range of-20 V/m to 60 V/m. It is found that the result predicted by the model is in agreement with the experimentally obtained one, with the error less than 5 percent for the thin biofilms. The error increases with the increase of the biofilm thickness. The transport rate of ions caused by electric migration is affected by the charges, field strength, and biofilm thickness and so on.     

典型软垫家具材料火灾特性的小尺寸实验研究

本文借助锥型量热计对制作软垫家具的材料进行小尺寸实验,获得了典型软垫家具面料、聚氨酯海绵填料及其组合件的燃烧性能参数。通过对实验获得参数的分析比较,认为面料对组合件燃烧特性的影响大,仅使用阻燃布就可以明显改善组合的火灾特性。     

岩土破坏过程声发射特征的实验研究

通过对重庆黄泥包滑坡处采集的岩土试样进行单轴压缩和拉伸实验,测试了岩土破坏过程的声发射信号,得出了岩土破坏过程声发射的基本特征:在单轴压缩实验中,声发射能量信号随着压力的增加呈现连续增加的趋势,在主破裂时刻有较强声发射能量信号产生;在蠕变实验中,AE在压力上升阶段信号增强,在恒定压力下,AE信号有所减弱,整体趋势较为平缓;在拉伸实验中,岩土的破坏方式呈主震型和群震型;AE信号能够反映岩土受载过程;岩土的抗压强度与声发射能量最大值呈正相关性;加载速率越大,声发射能量最大值也越大。     

基于RFPA2D复合局部挠曲岩体数值模拟

为研究复合局部挠曲岩体强度特征以及破坏规律,采用岩石真实破裂软件RFPA^2D,对水平层面挠曲30°,45°,60°,75°的复合岩体进行单轴压缩试验模拟。模拟结果表明:挠曲角为30°,45°,60°,75°的复合岩体破坏面几乎与挠曲段夹层重合,其挠曲端部均产生了垂直于挠曲段夹层的裂纹;复合单斜岩体与复合挠曲岩体破坏面的形成因素大致相同,夹层强度是2种岩体失稳的主要因素;复合挠曲岩体单轴抗压强度随挠曲角增大同样呈“U”型变化,与单斜岩体变化趋势一致;当水平层状岩体发生挠曲后,其单轴抗压强度减小,当挠曲角为60°时,强度降低25.19%,当挠曲角为75°时,强度降低0.17%。;随着均质系数m的增大,复合挠曲岩体单轴抗压强度以及轴向应变均出现逐渐递增的趋势,且不同m值,其岩体裂隙扩展方式具有明显差别。     

高效液相色谱-三重四级杆/复合线性离子阱质谱法测定饮用水中22种邻苯二甲酸酯

建立了一种同时测定饮用水中22种邻苯二甲酸酯(PAEs)的高效液相色谱-三重四级杆/复合线性离子阱质谱方法:饮用水样品经针头过滤器过滤,选用Biphenyl液相色谱柱进行分离,以含0.1%甲酸的水溶液和含0.1%甲酸的甲醇溶液为流动相,电离模式为电喷雾正离子,选用多反应监测触发增强子离子扫描模式进行检测。结果表明,22种PAEs的灵敏度良好,定量限为0.001～0.1 μg/L。配制浓度为0.1～100.0 μg/L的混标溶液进行进样分析,分析结果显示,22种PAEs在该范围内的线性关系良好,相关系数均大于0.995,方法的平均回收率为82.9%～108.9%,相对标准偏差为0.9%～11.2%。同时,使用增强子离子扫描谱图进行搜库匹配,定性准确性高。该方法适用于饮用水中PAEs的检测。     

液氮泡沫发生器内流动特性研究

低温液氮与泡沫混合液直接接触产生氮气泡沫是一种新型的掺混形式,利用液氮高汽化比的特点,搭建液氮泡沫可视化实验装置,进行氮气-水两相流及液氮泡沫流动特性的研究。结果表明,液氮相变产生大量氮气,其与泡沫液混合产生泡沫,温度有所回升,最终趋于泡沫混合液温度;管路沿程压降较小;液氮射流破碎及流动过程可分为6个区域:低温液氮区、向上循环翻滚区、滞留区、泡沫与泡沫混合液混合区、致密泡沫区、泡沫混合液区。流体向下游流动过程中持续发泡;为防止管路结冰,需合理控制泡沫混合液与液氮流量。     

An LC-MS/MS method for creatine and creatinine analysis in paraquat-intoxicated patients

Abstract

A sudden increase in serum creatinine after paraquat intoxication has been reported in several clinical studies. However, this dramatic change of creatinine may be possibly due to an interconversion of creatine-creatinine in relation to paraquat toxicity. In order to investigate the creatine-creatinine relationship, a liquid chromatography tandem mass spectrometry in combination with electrospray ionization was developed and validated for simultaneous determination of creatine and creatinine in the serum. The chromatographic separation was achieved on a Gemini® C₆-Phenyl column with a gradient elution consisting of 0.1% formic acid in ultrapure water and methanol as the mobile phase. The method yielded suitable levels of specificity and selectivity, and calibration curves of creatine and creatinine in serum were linear over the concentration range of 0.5–200?µg mL^?1. The limit of quantification of both compounds was 0.5?µg mL^?1, and the method was accurate within the recovery range of 96.23–102.75%, indicating the robustness of the method. The method was successfully applied to toxicological samples from paraquat-intoxicated patients, and the concentrations of creatine and creatinine were quantified. High creatine concentrations in serum samples were observed which may lead to high serum creatinine despite normal kidney function as creatine is converted to creatinine in proportion to its concentration.     

Validation of a booted finite element model of the WIAMan ATD lower limb in component and whole-body vertical loading impacts with an assessment of the boot influence model on response

Objective: A novel anthropomorphic test device (ATD) representative of the 50th percentile male soldier is being developed to predict injuries to a vehicle occupant during an underbody blast (UBB). The main objective of this study was to develop and validate a finite element (FE) model of the ATD lower limb outfitted with a military combat boot and to insert the validated lower limb into a model of the full ATD and simulate vertical loading experiments.

Methods: A Belleville desert combat boot model was assigned contacts and material properties based on previous experiments. The boot model was fit to a previously developed model of the barefoot ATD. Validation was performed through 6 matched pair component tests conducted on the Vertically Accelerated Loads Transfer System (VALTS). The load transfer capabilities of the FE model were assessed along with the force-mitigating properties of the boot. The booted lower limb subassembly was then incorporated into a whole-body model of the ATD. Two whole-body VALTS experiments were simulated to evaluate lower limb performance in the whole body.

Results: The lower limb model accurately predicted axial loads measured at heel, tibia, and knee load cells during matched pair component tests. Forces in booted simulations were compared to unbooted simulations and an amount of mitigation similar to that of experiments was observed. In a whole-body loading environment, the model kinematics match those recorded in experiments. The shape and magnitude of experimental force–time curves were accurately predicted by the model. Correlation between the experiments and simulations was backed up by high objective rating scores for all experiments.

Conclusion: The booted lower limb model is accurate in its ability to articulate and transfer loads similar to the physical dummy in simulated underbody loading experiments. The performance of the model leads to the recommendation to use it appropriately as an alternative to costly ATD experiments.