射流曝气MBR处理啤酒废水的试验

射流曝气提高了系统的氧利用效率及传质效率.通过逐渐提高进水的容积负荷来考察系统的处理效果, 试验表明, 利用射流曝气MBR处理模拟啤酒废水是可行的, 系统对COD、氨氮、浊度平均去除率为95.74%,97.84%,99.5%.由于系统运行期间不排泥, 因此系统对P O43-的去除效果不佳, 平均去除率为42.9%.膜对...     

实验室煤与瓦斯突出模拟试验回顾及展望

为借鉴国内外煤与瓦斯突出模拟试验研究成果,查阅大量相关文献,进行分析和总结。以人们对煤与瓦斯突出试验研究的深入程度为主线,将实验室煤与瓦斯突出模拟试验的研究历程进行阶段划分。研究表明:20世纪50—60年代,成功诱导了突出,初步考察诸因素对突出的影响;70—90年代,深入探究突出发生的力学判据及突出过程,并提出数十种有关突出机理方面的假说;21世纪初,以组建三维模拟试验台进行试验为特点,大大提高了模拟试验条件与现场的相似度,但在力学加载系统的稳定性和可调性、模型的整体密封性、测试探头的精度等方面仍需改进。     

某机械陀螺长贮性能演变规律及性能退化模型研究

目的 针对长期贮存后机械陀螺的性能退化会影响制导系统侧偏和射程的问题,提出一种性能退化预测模型的建立方法,用于掌握机械陀螺长贮性能退化规律。方法 首先,针对机械陀螺结构特性和贮存环境,确定敏感应力为温度,加速模型为阿仑尼乌斯模型,开展机械陀螺的加速贮存试验。其次,对加速贮存试验过程中的机械陀螺进行周期性的参数检测,分析各性能参数随试验时间的性能退化演变规律,确定垂直漂移为其退化敏感参数。最后,拟合垂直漂移参数在各温度应力下的性能退化曲线,建立性能退化轨迹模型。结果 采用实际自然环境贮存6、7、8、10 a的性能数据对模型进行验证,模型预测准确度分别为86.70%、96.28%、91.53%、85.92%。结论 建立的性能退化模型评估准确度在85%以上,该模型可应用于指定贮存时间下机械陀螺仪的性能退化行为预测。     

填埋场原位好氧稳定化技术的应用现状及研究进展

综述了原位好氧稳定化技术的原理、系统构成、关键单元的设计和优化及终点评价,结合我国填埋场及垃圾特点,展望了该技术在我国的发展前景和挑战.均匀布气及配水是原位好氧稳定化项目实施过程中主要的难点.做好渗滤液导排保证堆体最优含水率、优化曝气及提气管道布局、分层整治并辅以高压局部曝气有望提高氧气利用率;采用分层回灌或者压力回灌以及控制回灌速率可分别改善液体回灌过程中的屏障效应和大孔隙出流效应,保障堆体布水均匀.好氧稳定化处理后垃圾腐殖土及场底土壤的风险评价体系及最终出路尚未明确,后期加强相关基础研究以指导工程应用是必要的.     

EGSB-CANON工艺启动及动力学特性

采用EGSB（Expanded Granular Sludge Bed）反应器,在启动全程自养脱氮（CANON）工艺中通过改变曝气方式以及优化曝气/非曝气逐步实现CANON工艺的稳定运行.通过研究不同曝气/非曝气条件下CANON工艺的脱氮性能的变化,探究系统内不同污泥粒径中功能菌的活性,揭示EGSB反应器不同的运行条件以及系统内不同粒径的微生物聚集体在CANON工艺启动过程中的影响机制与菌群结构特性.结果表明,当恒定曝气量为0.5L/min,曝气/非曝气为2：1（60min：30min）时,实现了AerAOB（Aerobic Ammonia-Oxidizing Bacteria）与AnAOB（Anaerobic Ammonium-Oxidation Bacteria）协同脱氮的目的,并成功将NOB（Nitrite-Oxidizing Bacteria）的活性由3.41mgN/（h·gVSS）抑制到0.75mgN/（h·gVSS）.在对AnAOB的双底物（NO₂^--N和NH₄⁺-N）抑制动力学结果进行Haldane拟合时,得到NH₄⁺-N和NO₂^--N的半饱和常数（k_s）、抑制动力学常数（k_h）分别为106.8,331.9mg/L,272.4,66.61mg/L,相关性系数（R²）分别为0.98133和0.99142.在CANON污泥颗粒化形成过程中,污泥粒径在0.154~0.335mm范围内主要以AerAOB为主,污泥粒径在1mm以上主要以AnAOB为主.不同粒径下微生物聚集体的协同作用以及稳定的群落结构实现了CANON工艺的稳定运行.     

Mechanistic insight into the biofilm formation and process performance of a passive aeration ditch (PAD) for decentralized wastewater treatment

• A Passive Aeration Ditch was developed to treat decentralized wastewater. • A model was developed to describe the process performance. • A high C/N ratio facilitates microbial growth but nitrification deteriorates. • A high salinity decreases both organic and nitrogen contaminants removal. Decentralized wastewater containing elevated salinity is an emerging threat to the local environment and sanitation in remote coastal communities. Regarding the cost and treatment efficiencies, we propose a passive aeration ditch (PAD) using non-woven polyester fabric as a feasible bubbleless aerator and biofilm carrier for wastewater treatment. Consideration has been first given to PAD’s efficacy in treating saline decentralized wastewater, and then to the impact of chemical oxygen demand-to-nitrogen (C/N) ratio and salinity on biofilm formation. A multispecies model incorporating the salinity effect has been developed to depict the system performance and predict the microbial community. Results showed that the PAD system had great capacity for pollutants removal. The biofilm thickness increased at a higher C/N ratio because of the boost of aerobic heterotrophs and denitrifying bacteria, which consequently improved the COD and total nitrogen removal. However, this led to the deterioration of ammonia removal. Moreover, while a higher salinity benefited the biofilm growth, the contaminant removal efficiencies decreased because the salinity inhibited the activity of aerobic heterotrophs and reduced the abundance of nitrifying bacteria inside the biofilm. Based on the model simulation, feed water with salinity below 2% and C/N ratio in a range of 1 to 3 forms a biofilm that can reach relatively high organic matter and ammonia removal. These findings not only show the feasibility of PAD in treatment of saline decentralized wastewater, but also offer a systematic strategy to predict and optimize the process performance.     

曝气-絮凝处理垃圾渗滤液研究

通过现场处理 ,对垃圾渗滤液的曝气 -絮凝处理进行了研究。结果表明该方法对渗滤液的色度、COD、总磷去除率达 80 %以上 ,对氨氮去除率达 60 %以上。在此基础上提出了最优综合控制指标     

堆肥系统的通风设计

对堆肥系统的两种不同风机选型方法及计算结果进行了比较.根据计算结果,方法二所选风机的风量、风压和功率都大于方法一所选的风机.对于堆肥系统,目前常用的风机选型方法为方法二.污泥堆肥中试的结果初步表明:方法二所选风机的风量偏大,而方法一所选风机的风量比较适宜.     

Thermal and Mechanical Properties of Plastics Molded from Sodium Dodecyl Sulfate-Modified Soy Protein Isolates

Soybean protein is a potential material for manufacturing of biodegradable plastics. The objective of this investigation was to characterize the thermal and mechanical properties of plastics made from sodium dodecyl sulfate (SDS)-modified soy proteins. Soy protein isolate (SPI) was prepared from defatted soy flour, modified with various concentrations of SDS, and then molded into plastics. The temperatures of denaturation of the modified soy protein increased at low SDS concentration and then decreased at high SDS concentration. At the same SDS concentration, the plastics molded from the modified soy proteins showed a similar temperature of denaturation, but a lower enthalpy of denaturation compared to the modified soy protein. Young's modulus of the plastics decreased as SDS concentration increased, and the tensile strength and strain at break of the plastics reached a maximum value at 1% SDS modification. Two glass transition temperatures were identified corresponding to the 7S and 11S globulins in SPI by dynamic mechanical analysis, and they decreased as SDS concentration increased. The SDS modification increased the water absorption of the plastics.     

沈阳市北部污水处理厂工艺设计的特点

详细介绍了污水处理厂的设计规模、SDAO污水处理工艺、各个单体构筑物的主要设计参数,SDAO工艺采用圆形曝气池,在工艺和结构设计上有所创新。污泥采用消化处理,污泥加热方式比较科学。