Mobile passive samplers: concept for a novel mode of exposure

Integrative passive sampling with devices such as semipermeable membrane devices generally relies on rigs for month-long static exposures in water. We evaluate here whether mobile exposures of passive samplers can provide reliable estimates of dissolved contaminant concentrations. Mobile exposures were obtained by towing samplers fastened to the end of a benthic trawl net. Significant and reproducible absorption of polycyclic aromatic hydrocarbons during 5 h-long deployments was made possible by high sampling rates resulting from high water turbulences during towing at 1.2-1.5 knots. Sampling rates (72-215 L d⁻¹) estimated from the dissipation of performance reference compounds were supported by in situ calibration with samplers exposed for a 30 days in the vicinity of the test site. Higher fluoranthene and pyrene absorption in samplers exposed to the trawling-induced sediment plume could be attributed to desorption from re-suspended sediments. This mode of exposure has the potential to be used in monitoring programmes.     

Experimental thermal storage research of organic binary phase change materials in building environment

This paper aims to reveal the heat transfer mechanism of low-temperature phase change material (PCM) and design PCM heat storage device in building heating environment. Firstly, low-temperature binary PCMs of lauric acid and stearic acid are prepared, and their thermal properties are investigated by DSC. Then, shell and tube latent heat thermal energy storage units are conducted, and heat transfer experiments are carried out to analyze the heat transfer mechanism of PCM. The results demonstrate that natural convection plays an important role in heat transfer process, and the heat storage efficiency of PCMs can be significantly enhanced by increasing the fin width and improving the inlet heat transfer fluid (HTF) temperature. Furthermore, some proposals are put forward to guide the design of PCM storage device in building heating environment.     

Investigation of titanium liquid/gas diffusion layers in proton exchange membrane electrolyzer cells

In a proton exchange membrane electrolyzer cell (PEMEC), liquid/gas diffusion layer (LGDL) is expected to transport electrons, heat, and reactants/products to and from the catalyst layer with minimum voltage, current, thermal, interfacial, and fluidic losses. In addition, carbon materials, which are typically used in PEM fuel cells (PEMFCs), are unsuitable in PEMECs due to the high ohmic potential and highly oxidative environment of the oxygen electrode. In this study, a set of titanium gas diffusion layers with different thicknesses and porosities are designed and examined coupled with the development of a robust titanium bipolar plate. It has been found that the performance of electrolyzer improves along with a decrease in thickness or porosity of the anode LGDL of titanium woven meshes. The ohmic resistance of anode LGDL and contact resistance between anode LGDL and the anode catalyst play dominant roles in electrolyzer performance, and better performance can be obtained by reducing ohmic resistance. Thin titanium LGDLs with straight-through pores and optimal pore morphologies are recommended for the future developments of low-cost LGDLs with minimum ohmic/transport losses.     

膜蒸馏去除水中砷的研究

采用新型膜蒸馏技术对水中As（III）与As（Ⅴ）的去除展开了研究。实验结果表明,膜蒸馏对水中As (III)及As (Ⅴ)具有较高的去除能力：当产水中砷含量超过10 μg/L时,原水中As (III)与As (Ⅴ)的浓度可分别高达40 mg/L和2 000 mg/L。局部润湿现象的存在导致As (III)及As (Ⅴ)跨膜至产水侧,PVDF微孔膜在溶液中的负电性以及As (III)与 As (Ⅴ)在溶液中存在形式的不同导致膜蒸馏对两者去除能力的差异。360 h连续运行过程中产水通量及电导率稳定,且整个过程中As (III)均低于检测限,说明PVDF微孔膜具有良好的疏水性和稳定的除砷性能。     

好氧硝化颗粒污泥膜生物反应器性能和膜污染研究

实验研究了好氧硝化颗粒污泥膜生物反应器AGMBR的处理性能,并将其与活性污泥膜生物反应器ASMBR进行对比,考察了颗粒污泥在减缓膜污染中所起的作用.好氧硝化颗粒污泥膜生物反应器AGMBR连续稳定运行102 d,系统具有良好的去除有机物和同时硝化反硝化能力,在进水COD和NH+4-N浓度分别为500和200 mg/L时,COD、NH+4-N和TN的去除率分别稳定在86%、94%和45%以上.颗粒污泥有效减缓了膜污染,延长了膜清洗的周期,AGMBR中的膜污染以膜孔堵塞为主,占总阻力的64.81%;滤饼层的阻力为2.1×1012m-1,远小于ASMBR中的16.07×10"m-1;膜清洗周期是相同条件下ASMBR的2.43倍以上;而且AGMBR内不断有新颗粒生成,维持了AGMBR系统性能和运行的稳定.     

微曝气Fenton氧化法处理模拟双酚A废水的效果及其生物验证

研究了微曝气Fenton氧化法关键工艺参数对模拟双酚A（BPA）废水处理效果的影响,并从活性污泥性质和污染物去除率两方面,采用膜生物反应器(membrane bioreactor, MBR)对微曝气Fenton氧化法的处理效果进行了实验验证,为实现BPA废水的生物处理奠定基础。结果表明,初始pH值、反应时间、H₂O₂/COD(质量浓度比)、H₂O₂/Fe²⁺ (摩尔浓度比)、反应温度及曝气量均对预处理效果有较大影响,在最佳条件下,COD去除率可达70%,BOD/COD值则由原废水的0.02提高到0.50以上。MBR处理上述出水的结果表明,经微曝气Fenton氧化处理BPA的废水,可较好地适应后续的生化处理。     

活性炭在膜生物反应器中的应用研究进展

活性炭是一种非常优良的吸附剂,具有物理吸附和化学吸附的双重特性。本文介绍了近年来向膜生物反应器中投加活性炭的应用研究进展,表明投加活性炭可以提高膜生物反应器的处理效果,同时对改善膜污染有很好的效果。     

膜生物反应器中溶解性微生物产物特性的研究进展

溶解性微生物产物是制约生物处理出水达标和回用的主要污染物,处理工艺和操作条件的不同可能造成其特性差异。阐述了溶解性微生物产物的定义和产生机制,对膜生物反应器中溶解性微生物产物的组成、分子质量分布、亲水／疏水性、螯合性和毒性进行了概述,分析了影响其产生、特性和去除的因素。由于膜的截留作用使溶解性微生物产物在膜生物反应器中积累,容易引起膜污染。可以通过优化操作条件,减少溶解性微生物产物的产生,提高出水水质,有效地抑制膜污染。     

陶瓷膜污染过程分析与膜清洗方法优化

采用膜孔径为50 nm的陶瓷膜错流过滤方式,对碱性高浓度有机洗涤废水进行9个周期的膜通量衰减及反向脉冲清洗再生实验研究.通过设计膜污染阻力构成实验,测算膜污染总阻力及其构成比例.实验结果表明,膜固有阻力比例较低,浓差极化污染较弱,Rt和Rc+Rirt污染阻力稳定性较高,膜堵塞形式兼有孔内堵塞和滤饼过滤;选择质量分数0.1％的稀盐酸和0.2％的草酸溶液膜清洗效果均较好,清洗时间为3 min,脉冲时间和频率为3 s/5 s.     

混凝剂品种对混凝-超滤联合工艺膜污染的影响

本实验以工业化学合成聚合硫酸铁混凝剂和自制生物聚合硫酸铁为例,考察了铁系混凝剂品种对地表水浊度、TOC和UV254的去除效果,混凝剂品种对混凝-超滤联合工艺处理地表水过程中超滤膜污染的影响。混凝实验结果表明,在10 mg/L(以Fe3+计)最佳投加量下,两类混凝剂对浊度、TOC和UV254的去除率基本相同。超滤膜污染实验结果表明,生物聚合铁预处理水样通量衰减速度略大于化学聚合铁预处理水样;膜污染阻力分析结果显示,随着循环次数的增加,工业化学合成聚合铁预处理水样造成的不可逆污染阻力逐渐增加,而生物聚合铁预处理水样造成的不可逆污染阻力却略有下降;膜污染机理分析表明,2组过滤过程的膜污染类型基本相似,由最初的膜孔堵塞过渡到最终的滤饼层污染。SEM分析表明,生物聚合铁预处理水样的膜污染较为严重。