Supercritical water oxidation of polyvinyl alcohol and desizing wastewater：Influence of NaOH on the organic decomposition

Polyvinyl alcohol is a refractory compound widely used in industry. Here we report supercritical water oxidation of polyvinyl alcohol solution and desizing wastewater with and without sodium hydroxide addition. However, it is difficult to implement complete degradation of organics even though polyvinyl alcohol can readily crack under supercritical water treatment. Sodium hydroxide had a significant catalytic effect during the supercritical water oxidation of polyvinyl alcohol. It appears that the OH ion participated in the C-C bond cleavage of polyvinyl alcohol molecules, the CO2-capture reaction and the neutralization of intermediate organic acids, promoting the overall reactions moving in the forward direction. Acetaldehyde was a typical intermediate product during reaction. For supercritical water oxidation of desizing wastewater, a high destruction rate (98.25%) based on total organic carbon was achieved. In addition, cases where initial wastewater was alkaline were favorable for supercritical water oxidation treatment, but salt precipitation and blockage issues arising during the process need to be taken into account seriously.     

Waste oyster shell as a kind of active filler to treat the combined wastewater at an estuary

Estuaries have been described as one of the most difficult environments on Earth. It is difficult to know how to treat the combined wastewater in tidal rivers at the estuary, where the situation is very different from ordinary fresh water rivers. Waste oyster shell was used as the active filler in this study in a bio-contact oxidation tank to treat the combined wastewater at the Fengtang Tidal River. With a middle-experimental scale of 360 ma/day, the average removal efficiency of COD, BOD, NH3-N, TP and TSS was 80.05%, 85.02%, 86.59%, 50.58% and 85.32%, respectively, in this bio-contact oxidation process. The living microbes in the biofilms on the waste oyster shell in this bio-contact oxidation tank, which were mainly composed of zoogloea, protozoa and micro-metazoa species, revealed that waste oyster shell as the filler was suitable material for combined wastewater degradation. This treatment method using waste oyster shell as active filler was then applied in a mangrove demonstration area for water quality improvement near the experiment area, with a treatment volume of 5 × 10^3 m^3/day. Another project was also successfully applied in a constructed wetland, with a wastewater treatment volume of 1 ×10^3 m^3/day. This technology is therefore feasible and can easily be applied on a larger scale,     

磁性多孔陶粒生物膜反应器处理焦化废水的试验研究

以磁性材料为原料,经过特定的工艺处理,对多孔陶瓷进行磁化改性获得磁性多孔载体,并将该载体应用于生物膜反应器中进行焦化废水处理试验。对不同类型的多孔陶粒载体进行对比试验,结果表明:磁性载体生物膜反应器对COD、NH3-N的去除率比普通活性污泥法高出25%³0%,比非载体生物膜反应器高出15%30%,比非载体生物膜反应器高出15%²0%左右。反应器的曝气量为1.5 L/h,曝气时间为10 h/d,温度为2520%左右。反应器的曝气量为1.5 L/h,曝气时间为10 h/d,温度为25³0℃。焦化废水经磁性载体生物膜反应器处理后,上清液中COD,NH3-N的去除率均在90%左右。出水浓度达到国家工业废水排放二级标准(GB18918-2002)。     

呼和浩特地区污水厂能耗评价与碳排放分析

污水处理过程的能耗和温室气体排放方面的研究对于应对能源危机和气候危机具有重要作用。文章利用层次分析法,建立了具有4层15项指标的能耗评价体系。结合城镇污水处理系统的绿色指标体系,选取呼和浩特地区具有代表性、处理规模相近的2座中小型污水厂进行能耗评价。结果表明:处理能力利用率、处理工艺系统稳定性和污水厂高程布置所对应的3项评价指标在所选择的能耗影响因素中所占权重较大,分别为:0.143 0,0.302 4和0.145 6。进一步运用IPCC计算方法对污水处理厂进行碳排放概算,得出A、B污水处理厂的碳排放量分别为:19.401 t CO2/104t、18.378 t CO2/104t。A、B污水处理厂的实际比能耗分别为0.293 kW.h/m3、0.195 kW.h/m3。将碳排放数据与实际能耗情况对比得出:污水处理厂的能耗水平越高,单位碳排放量也越大。     

纳米Fe_3O_4/膨润土的制备、表征及光催化降解焦化废水

以铝柱撑膨润土负载纳米Fe_3O_4制备出性能良好的复合型催化剂。结合X射线粉末衍射(XRD)、扫描电镜(SEM)和比表面孔隙分析(BET)对催化剂的晶相、比表面积和粒度进行表征。负载的纳米Fe_3O_4粒径约为20～30nm,均匀分散到膨润土表面,未发生明显的团聚。在紫外光作用下用该催化剂对焦化厂二沉池出水进行深度处理。结果表明,在催化剂投加量为0.7 g/L,pH为2.5,温度40℃,H_2O_2初始浓度为17.6mmol/L的反应条件下,二沉池出水(化学需氧量COD=140mg/L,色度=400度)经催化氧化降解后,COD和色度可分别降低到54.44 mg/L和10度,达到国家工业再生用水水质标准GB/T 19923-2005(COD≤60 mg/L,色度≤30度)。催化剂重复使用4次时,废水COD和色度去除率保持稳定。     

非均相类Fenton试剂的制备及其在焦化废水处理中的应用研究

利用浸渍法,将Fe3＋负载在经酸碱改性后的粉状活性炭上,当浸渍液浓度为2．5％,固化温度为270℃时,制成的催化剂催化活性较高。用自制的非均相类benton试剂降解焦化废水,通过正交试验和极差分析得出,影响因素的主次顺序为催化剂用量〉初始pH值〉反应时间〉H：0：投加量。结果表明,在100ml水样中。室温条件下,初始pH值为4．0,催化剂使用量为1．5g,H20：投加量为5ml（分两次投加）,反应时间为90min时,COD去除率可达99％。采用混凝＋化学沉淀＋非均相类Fenton试剂法处理焦化废水,各主要出水水质指标为：色度lO倍;COD浓度38．5mg／L;氨氮浓度8．4mg／L,达到国家一级排放标准。     

电化学强化低能耗废水生物处理技术研究

以碳布为阴阳极材料构建一种新型的生物电化学系统（BES）,研究该系统在不曝气条件下对城市污水的处理效果,并与传统的厌氧和好氧处理方法进行比较。结果表明,该BES处理城市污水是可行的,与传统曝气法相比能够显著降低能耗。在进水CODcr,为350mg／L、NH3-N为15mg／L、水力停留时间（HRT）为24h时,电化学强化生物处理系统对CODcr和NH3-N的去除率达84％和80％,优于同等条件下的厌氧、好氧生物处理方法。BES的输出电压最高为211mV。     

高碳氮负荷下同时脱氮除碳好氧颗粒污泥研究

在4 L反应器中,以补加葡萄糖和硫酸铵的猪场废水为基质,不接种活性污泥,加入粉末状活性炭对废水土著微生物进行预固定.通过批次进水并控制运行条件（逐渐提高COD、NH 4＋-N负荷、缩短沉降时间、提高曝气量）培养同时脱氮除碳好氧颗粒污泥,研究了该好氧颗粒污泥的脱氮除碳功能及对高碳氮负荷冲击的响应.结果表明,成熟好氧颗粒污泥为土黄色不规则球状,粒径为0.5～3.5 mm.COD和NH 4＋-N负荷分别在4.80～12.6 kg.（m3.d）-1和0.217～0.503 kg.（m3.d）-1时,好氧颗粒污泥对COD的去除率〉94%,对NH 4＋-N的去除率〉98%.当COD和NH 4＋-N负荷分别提高至15.70 kg.（m3.d）-1和0.723kg.（m3.d）-1并运行4 d后,反应器内絮体激增,颗粒沉降变差并开始破碎,NH 4＋-N去除率下降至81.6%.排出部分污泥并降低负荷继续运行,颗粒污泥的NH 4＋-N去除率可迅速恢复至98%以上.本研究培养的好氧颗粒污泥具有良好的同时脱氮除碳功能,可以耐受高COD和NH 4＋-N负荷的双重冲击.     

pH和DO对好氧颗粒污泥去除高氨氮废水的影响研究

研究使用SBR成功培养的结构紧密、外形规则,具有良好脱氮性能的成熟好氧颗粒污泥处理高浓度氨氮废水,并探讨pH和DO对其处理效果的影响,旨在为工程实践提供理论依据。通过人工模拟废水,以蔗糖作为唯一碳源,NH4Cl为氮源,将进水NH4+-N浓度由300 mg/L逐步提高至900 mg/L,相应的NH4+-N负荷由0.6 kg/(m3.d)提高至1.8 kg/(m3.d),考察pH和DO对其处理效果的影响。研究结果表明:当控制反应器pH为8.0,曝气量为75 L/h时,好氧颗粒污泥脱氮的效果最好,氨氮去处率分别为96.70%9、2.33%。由于运行过程中每隔15 min监测每个反应器pH值,使其维持在各自pH值7.0±0.1范围内。这种酸碱度环境对异养菌等微生物并没有产生抑制作用;因此在各pH条件下,COD去除的所需时间和去除率基本没有差别。在不同的DO下,COD在初始的60 min里降解速度有明显区别。曝气量为150 L/h时,COD的降解速度最快,但是曝气量过大颗粒污泥内部厌氧区被压缩,因此选择最佳的曝气量为75 L/h。