聚(苯乙烯-甲基丙烯酸)复合磁性微球的吸附性能

以共沉淀法制备纳米Fe3O4,通过分散聚合法制备了磁性聚(苯乙烯-甲基丙烯酸)(Fe3O4@P(St-MMA))微球,采用光学显微镜、红外光谱、样品磁力振荡计和X射线衍射(XRD)对磁性微球进行了表征。考察了复合磁性微球在不同的p H、离子强度和吸附时间等条件下对其吸附性能的影响,运用吸附动力学和吸附等温线研究了磁性微球对亚甲基蓝的表面吸附机理。结果表明,制备的磁性微球粒径在100~200μm之间,表面含有羧基,饱和磁化强度为9.44 emu/g,在外加磁场的作用下能够快速分离出来。亚甲基蓝的吸附符合准二级动力学模型,在100 min内基本达到吸附平衡;25℃下,最大吸附量高达144.9 mg/g,且吸附随着p H值的升高而增加,当p H7时,吸附量基本不变;随着离子强度增加,吸附量逐渐下降;Langmuir等温线能比较好地拟合磁性微球对溶液中亚甲基蓝的吸附。     

羧甲基纤维素抑尘剂的制备及其应用研究

以羧甲基纤维素、丙烯酸丁酯、甲基丙烯酸甲酯为原料,用溶液聚合法制备出一种环保软膜抑尘剂.探讨了添加甘油、辛癸基葡糖苷对抑尘剂吸水性能、润湿性能的变化以及m(甘油):m(辛癸基葡糖苷)以不同配比加入抑尘剂后对粉尘含水率的影响.经傅里叶红外光谱、X-射线衍射仪、扫描电子显微镜、透射电子显微镜对制备的产物进行结构表征和形貌的分析.对抑尘剂的性能:耐风蚀性、温度适应性进行了测试.结果表明:当m(甘油):m(辛癸基葡糖苷)为2:3,室温时粉尘含水率达15.8%、50℃粉尘含水率仍可达11.7%;经3 h(15 m/s)风速吹扫,粉尘损失率仅为2.3%.     

Beijing Tong Ren Tang Company Limited Scientific Research Institute, Beijing 100011, China

By dynamic method under UV irradiation,commercial melt-blown polypropylene(PPMB)filter element was modified with acrylamide(AAm)using benzophenone(BP)as initiator.Attenuated total reflection-Fourier transform infrared spectroscopy and scanning electron microscope verified that polyacrylamide chain was grafted on the fiber surface of PPMB filter element.Elemental content analysis with energy dispersive X-ray of fibers revealed that the polymerization content in the inner part of filter element was relatively higher than that in the outer.Degree of grafting changed with initiator concentration,monomer concentration,reaction temperature and reached 2.6% at the reaction condition:C_(BP)=0.06 mol/L,C_(AAm)=2.0 mol/L,irradiation time:80 min,temperature: 60℃.Relative water flux altered with the hydrophilicity and pore size of filter element.In the antifouling test,the modified filter gave greater flux recovery(approximately 70%)after filtration of the water extract of Liuweidihuang,suggesting that the fouling layer was more easily reversible due to the hydrophilic nature of the modified filter.     

Performances of biological aerated filter employing hollow fiber membrane segments of surface-improved poly （sulfone） as biofilm carriers

Using the surface of poly （sulfone） hollow fiber membrane segments as grafted layer, the hydrophilic acrylamide chain was grafted on by UV-photoinduced grafting polymerization. The gained improvement of surface wettability for the modified membrane was tested by measuring the contact-angle as well as FTIR spectra. Then correlation between the hydrophilic ability of support material and the biofilm adherence ability was demonstrated by comparing the pollutant removal rates from urban wastewater via two identical lab-scale up-flow biological aerated filters, one employed the surface wettability modified poly （sulfone） hollow fiber membrane segment as biofilm carder and the other employed unmodified membrane segment as biofilm carder. The experimental results showed that under the conditions of influent flux 5 L/h, hydraulic retention time 9 h and gas to liquid ratio （G/L） 10： 1, the removal rates of chemical oxygen demand （COD） and ammonium nitrogen （NH4^＋-N） for the modified packing filter and the unmodified packing filter was averaged at 83.64% and 96.25%, respectively, with the former filter being 5%-20% more than the latter. The effluent concentration of COD, NH4^＋-N and turbidity for the modified packing filter was 25.25 mg/L, 2 mg/L and 8 NTU, respectively. Moreover, the ammonium nitrogen removal performance of the filter packing the modified PSF was compared with the other bioreactor packing of an efficient floating medium. The biomass test indicated that the modified membrane matrixes provided better specific adhesion （3310-5653 mg TSS/L support）, which gave a mean of 1000 mg TSS/L more than the unmodified membrane did. In addition, the phenomenon of simultaneous denitrification on the inner surface of the support and nitrification on the outer surface was found in this work.     

Span80-Tween60/T154/煤油/H2SO4微乳液膜处理氨氮废水

研究了以Span80和Tween60为混合表面活性剂的微乳液膜的配方及其稳定性,通过Span80-Tween60/T154/煤油/H2SO4微乳液膜体系处理氨氮废水的研究,考察了表面活性剂的配比、T154的浓度、萃取时间、乳水比、外水相pH值、油相回用次数等因素对氨氮萃取率的影响。实验结果表明,当Span80和Tween60的质量比为4∶1,T154在煤油中的质量浓度为5％,萃取时间为15 min,乳水比为1∶14,外水相pH值为9时,氨氮一次性萃取率可到99.85％;该微乳液膜不仅稳定性好,对氨氮萃取率高,而且制乳、破乳容易,油相可重复使用。     

微乳液对难溶有机物的增溶作用及影响因素

研究了蓖麻油硫酸盐(SCOS)微乳液对1,4-二氯苯(DCB)、1,2,3,-三氯苯(TCB)、联苯(BP)和芘(Py)等难溶有机物的增溶作用.SCOS微乳液较阴离子或非离子表面活性剂胶束溶液具有更强的增溶能力;有机物的表观溶解度与微乳液中SCOS的浓度呈正相关,DCB、TCB、BP和Py在SCOS微乳相与水相间的分配系数(logKem)分别为3.15, 4.03, 3.95和5.01;温度、共存有机物和无机盐影响SCOS微乳液对有机物的增溶作用.     

Thermal research on the uncontrolled behavior of styrene bulk polymerization

Thermal runaway can occur during the styrene bulk polymerization process because of easily formed local hotspots resulting from the high viscosity of reactants and the difficulty of heat dissipation. To obtain the thermal hazard characteristics, the polymerization behavior of styrene was investigated using differential scanning calorimetry (DSC) at a scanning rate of β = 2 °C/min. Experimental results showed that the exothermic peaks obtained for heat initiation were different from those obtained when initiator was added. The exothermic peak changed from one to two after the initiator was added. The exothermic onset temperature (T₀) was also reduced. Phi-tech II was utilized to study the bulk polymerization of styrene in an adiabatic environment. The adiabatic temperature rise (ΔT_ad), starting temperature of uncontrolled polymerization (T_star), maximum temperature (T_end), and heat of polymerization (ΔH) under different conditions were acquired. When the dose of the additive was increased, the starting temperature of uncontrolled polymerization (T_star) decreased and the adiabatic temperature rise (ΔT_ad) increased gradually. Severity grading was performed based on the severity evaluation criteria of runaway reaction. The results can help designers decide whether it is necessary to take certain measures to reduce risk.     

应用CAMEO软件包预测聚合反应器丙烯泄漏影响范围

为了能够准确地预测聚合反应器发生泄漏时丙烯的扩散分布,提高应急救援工作效率,应用CAMEO软件包进行预测,通过该软件包中ALOHA、MARPLOT软件连用,解决了量化和图形显示问题。     

磁性离子印迹聚合物的制备及其对水中Pb(Ⅱ)的吸附

以铅离子为模板离子、乙二醇二甲基丙烯酸酯和偶氮二异丁腈为交联剂和引发剂、稀盐酸为洗脱剂,采用微波辅助反相乳液悬浮聚合法,制备了磁性离子印迹聚合物(MIIP),通过SEM、FTIR、XRD和BET技术对其进行了表征,并将其用于水中Pb(Ⅱ)的吸附.在初始质量浓度60 mg/L、溶液pH 6、吸附温度303 K、吸附时间6...     

悬浮法氯乙烯聚合工艺的风险分析及安全技术

悬浮法聚合氯乙烯生产过程的主要风险是氯乙烯的"暴聚"事故和氯乙烯泄漏事故.聚合反应散热不足,温度过高导致"暴聚"事故.易燃易爆有毒的氯乙烯泄漏可能引发氯乙烯蒸汽云爆炸和火球(BLEVE)事故.以某PVC化工厂氯乙烯聚合釜生产为例,定量计算氯乙烯小孔泄漏量、蒸汽云及BLEVE火球的事故伤害与破坏后果.提出避免导致"暴聚"事故3种安全技术措施:良好的聚合釜反应散热降温;足够的搅拌强度和防止"粘釜"等.防止引发氯乙烯泄漏的3种途径为反应釜轴封、超压泄压时跑料和压力容器及管道的防泄漏技术.