武汉市秸秆燃烧VOCs排放估算及管理对策

秸秆燃烧是我国人为源挥发性有机物(volatile organic compounds,VOCs)排放的重要来源之一,其排放对气候变化和人体健康都有很大影响.对该来源VOCs排放量的可靠估算是在区域或城市范围内进行排放效应分析和污染控制的重要前提.根据2005~2011年武汉市农作物的总产量,采用排放因子分析法估算了武汉市及主要6个农作物产区的秸秆燃烧VOCs的排放量,并分别计算其耕地排放强度(I c)和区域排放强度(I r).结果表明,武汉市2005~2011年年均秸秆燃烧VOCs排放量约为(3 163±139)t,I c和I r分别为(1.52±0.06)t·km-2和(0.37±0.02)t·km-2.粮食类和油料类农作物秸秆燃烧是主要的排放源,需优先控制7大类21种VOCs物质.武汉市分区VOCs排放量从大到小排序依次为黄陂区、新洲区、江夏区、蔡甸区、汉南区、东西湖区,前4个区的排放总量占到武汉市的近九成.江夏区、汉南区、黄陂区和新洲区应作为秸秆燃烧VOCs排放的优先控制区,尤其是能作为全国代表性的江夏区,应引起高度重视.在进行区域或城市范围的秸秆燃烧产生污染物质的生态风险评价时,该污染物的I c和I r都是需要考虑的重要基础数据.最后,提出大力发展农村秸秆资源综合循环经济利用是解决区域或城市范围内秸秆燃烧产生环境问题的可行之径.     

氮氟掺杂二氧化钛(N,F-TiO2)的制备及可见光催化活性的研究

以氨水为氮源,氢氟酸为氟源,采用溶胶-凝胶法制备了氮氟掺杂二氧化钛(N,F-TiO2)光催化剂,并通过X-射线衍射(XRD)和扫描电镜(SEM)技术对其晶型和形态进行表征.最后以酸性红B为模型污染物,探讨了N和F加入量、焙烧温度、焙烧时间、照射时间、催化剂用量、溶液初始浓度和照射功率等因素对N,F-TiO2可见光催化活性的影响.结果表明,制备的N,F-TiO2以锐钛型为主,N和F的掺杂对TiO2的晶相没有明显改变,但可以扩大TiO2的可见光响应范围.当N和F的加入量均为2.0%,且在500℃下焙烧40 min时,得到的N,F-TiO2的可见光催化活性明显高于单N或单F掺杂的TiO2(N-TiO2或F-TiO2).对于50 mL浓度为10.0 mg·L-1的酸性红B溶液,当催化剂加入量为1.5 g·L-1,128W光照3.0 h,溶液pH=5.6时,去除率为85.40%.适当延长光照时间至4.0 h,降解率几乎可达100%.另外,研究还证明了N,F-TiO2催化可见光降解过程中有.OH自由基生成.     

流化床O2/CO2气氛下添加SiO2对燃煤PM2.5的控制

采用小型流化床研究了在O2/CO2气氛下添加SiO2对PM2.5(空气动力学直径小于2.5 μm的颗粒物)的控制,试验在1123 K、O2/CO2气氛下进行,并采用荷电低压撞击器(ELPI)采集和分析燃烧后的PM2.5.结果表明,添加SiO2是燃烧过程中影响PM2.5生成的重要因素.添加SiO2后,生成PM1的质量浓度均降低,而PM1-2.5的质量浓度均略有增加;PM2.5质量粒径分布均呈双峰分布,峰值分别出现在0.2 μm和2.0μm左右.随着SiO2添加量的增加,PM2.5中的S、K、Na、Cu和Pb元素的含量呈减少的趋势;随着颗粒粒径减小,S、K、Na、Cu和Pb元素的含量有增高的趋势.     

不同流态下微波辐射对污水污泥性质的影响研究

通过对不同流态下微波辐射对污水污泥性质的影响进行研究,考察了不同流态下微波辐射作用处理后污泥沉降性能、脱水性能的变化,以及微波辐射作用下流态对污泥挥发性悬浮固体(VSS)溶解率、上清液中COD和污泥微观形态的影响.结果表明,流态对污泥的沉降性能和脱水性能有一定影响,微波辐射功率越高,流态对污泥沉降性能和脱水性能的影响越显著.微波辐射功率较低时,雷诺数Re越大,污泥的沉降比(SV)、比阻和泥饼含水率越小;微波辐射功率较高时,Re为2300的临界流态下污泥的沉降性能和脱水性能最好.随着Re的增大,VSS溶解率和上清液中COD升高,微波辐射功率分别为300、500、700和900W时,Re为3000的紊流流态下上清液中COD分别达到1.1、2.1、3.6和6.7g·L-1.SEM观察结果表明,微波辐射及流态产生的协同剪切应时适宜时,有利于污泥颗粒的絮凝反应,高强度的微波辐射和紊流产生的较大剪切应力导致污泥絮体被打碎.     

单光子/光电子在线质谱实时分析聚氯乙烯热分解/燃烧产物

实验室研制了低能光电子磁场增强电离(MEPEI)和单光子电离(SPI)复合电离源,该电离源具有电离化合物范围宽、碎片离子少、质谱图简单等优点,结合飞行时间质谱(TOF-MS)实现了聚氯乙烯(PVC)热分解/燃烧产物的在线分析.针对不同的目标化合物,MEPEI/SPI复合电离源通过调节电离区电场强度,可以快速在SPI和SPI-MEPEI之间切换.PVC热分解/燃烧产物中电离能大于光子能量(10.60 eV)的HCl和CO2(12.74 eV、13.77 eV)利用MEPEI模式电离;而烯烃、二氯乙烯、苯系物、氯苯、苯乙烯、茚满及萘系物等可通过SPI-MEPEI复合模式电离.通过实时监测PVC主要燃烧产物的信号强度随温度的变化趋势可推断出,PVC燃烧产物主要是通过两种机制生成:①250～370℃时,PVC发生脱氯及分子内环化反应,产生大量的HCl、苯和萘;②380～510℃时,PVC发生分子间交联反应,生成烷基芳烃,如甲苯和二甲苯/乙苯等.实验结果表明,SPI/SPI-MEPEI复合离子源TOF-MS分析速度快,应用范围广,在在线分析中具有广泛的应用前景.     

直接大红4BE的磷钨酸均相光催化还原脱色

以磷钨酸(H3PW12O40,PW12)为光催化剂,异丙醇(Isopropanol)作为电子给体的条件下对偶氮染料直接大红4BE进行均相光催化还原脱色研究,考察PW12用量、IS浓度、直接大红4BE和盐浓度等因素的影响,结果表明杂多蓝(PW1-2)对直接大红4BE具有明显的还原脱色作用.pH=2.0,直接大红4BE初始浓度50 mg·L-1,PW12浓度为600 mg·L-1,IS浓度为0.13mol·L-1,50 min直接大红4BE的脱色率可达到90.39%.4BE的光催化还原脱色速率随PW12和IS浓度的增加而增加,最后趋于恒定;直接大红4BE初始浓度增加,其光反应一级速率常数降低;PW12、IS和4BE浓度之间存在交互影响.离子强度增加,4BE脱色速率减小,表现为负的盐效应,推测4BE与光反应生成的杂多蓝(PW1-2)进行复合,然后发生电子转移引起偶氮染料还原脱色和杂多蓝氧化复原.本研究结果表明PW12/IS/UV能够有效用于偶氮染料直接大红4BE的还原脱色处理.     

Pb(II) removal from water using Fe-coated bamboo charcoal with the assistance of microwaves

Bamboo charcoal(BC) was used as starting material to prepare iron-modified bamboo charcoal(Fe-MBC) by its impregnation in FeCl 3 and HNO 3 solutions simultaneously,followed by microwave heating.The material can be used as an adsorbent for Pb(Ⅱ) contaminants removal in water.The composites were prepared with Fe molar concentration of 0.5,1.0 and 2.0 mol/L and characterized by means of N 2 adsorption-desorption isotherms,X-ray diffraction spectroscopy(XRD),scanning electron microscopy coupled with energy dispersive X-ray spectrometry(SEM-EDS),Fourier transform infrared(FT-IR) and point of zero charge(pH pzc) measurements.Nitrogen adsorption analyses showed that the BET specific surface area and total pore volume increased with iron impregnation.The adsorbent with Fe molar concentration of 2 mol/L(2Fe-MBC) exhibited the highest surface area and produced the best pore structure.The Pb(Ⅱ) adsorption process of 2Fe-MBC and BC were evaluated in batch experiments and 2Fe-MBC showed an excellent adsorption capability for removal Pb(Ⅱ).The adsorption of Pb(Ⅱ) strongly depended on solution pH,with maximum values at pH 5.0.The ionic strength had a significant effect on the adsorption at pH < 6.0.The adsorption isotherms followed the Langmuir isotherm model well,and the maximum adsorption capacity for Pb(Ⅱ) was 200.38 mg/g for 2Fe-MBC.The adsorption processes were well fitted by a pseudo second-order kinetic model.Thermodynamic parameters showed that the adsorption of Pb(Ⅱ) onto Fe-MBC was feasible,spontaneous,and exothermic under the studied conditions,and the ion exchange mechanism played an significant role.These results have important implications for the design of low-cost and effective adsorbents in the removal of Pb(Ⅱ) from wastewater.     

Formic acid as an alternative reducing agent for the catalytic nitrate reduction in aqueous media

Formic acid was used for the nitrate reduction as a reductant in the presence of Pd:Cu/γ-alumina catalysts. The surface characteristics of the bimetallic catalyst synthesized by wet impregnation were investigated by SEM, TEM-EDS. The metals were not distributed homogeneously on the surface of catalyst, although the total contents of both metals in particles agreed well with the theoretical values. Formic acid decomposition on the catalyst surface, its influence on solution pH and nitrate removal efficacy was investigated. The best removal of nitrate (50 ppm) was obtained under the condition of 0.75 g/L catalyst with Pd:Cu ratio (4:1) and two fold excess of formic acid. Formic acid decay patterns resembled those of nitrate removal, showing a linear relationship between kf (formic acid decay) and k (nitrate removal). Negligible amount of ammonia was detected, and no nitrite was detected, possibly due to buffering effect of bicarbonate that is in situ produced by the decomposition of formic acid, and due to the sustained release of H2 gas.     

OMS-2负载Pt催化剂的制备及其催化氧化性能研究

采用前掺杂法、沉积-沉淀法和浸渍法制备了氧化锰八面体分子筛(OMS-2)负载Pt催化剂(Pt/OMS-2),对所制催化剂进行了结构和织构表征。并研究了不同制备方法和沉积-沉淀法中不同制备(Pt负载量和溶液的pH值)对Pt/OMS-2催化氧化CO性能的影响。结果表明,沉积-沉淀法制备的Pt/OMS-2-DP催化剂活性最好(T100=100℃)。这与Pt/OMS-2-DP催化剂中Pt颗粒大小及OMS-2载体与Pt之间存在强相互作用有关。Pt负载量明显影响Pt/OMS-2-DP催化剂的催化活性,3Pt/OMS-2-DP催化剂(Pt=3.0 wt%)催化活性最高,这是由于适当Pt负载量,Pt颗粒较小,并与载体OMS-2的相互作用较强,能较好地活化OMS-2晶格氧。pH值对Pt/OMS-2-DP催化剂催化性能影响较大,这与OMS-2的等电点和Pt在不同溶液中存在不同Pt配位体形式有关。     

非均相类Fenton试剂的制备及其在焦化废水处理中的应用研究

利用浸渍法,将Fe3＋负载在经酸碱改性后的粉状活性炭上,当浸渍液浓度为2．5％,固化温度为270℃时,制成的催化剂催化活性较高。用自制的非均相类benton试剂降解焦化废水,通过正交试验和极差分析得出,影响因素的主次顺序为催化剂用量〉初始pH值〉反应时间〉H：0：投加量。结果表明,在100ml水样中。室温条件下,初始pH值为4．0,催化剂使用量为1．5g,H20：投加量为5ml（分两次投加）,反应时间为90min时,COD去除率可达99％。采用混凝＋化学沉淀＋非均相类Fenton试剂法处理焦化废水,各主要出水水质指标为：色度lO倍;COD浓度38．5mg／L;氨氮浓度8．4mg／L,达到国家一级排放标准。