Effect of pyrolysis and oxidation characteristics on lauric acid and stearic acid dust explosion hazards

The effect of pyrolysis and oxidation characteristics on the explosion sensitivity and severity parameters, including the minimum ignition energy MIE, minimum ignition temperature MIT, minimum explosion concentration MEC, maximum explosion pressure P_max, maximum rate of pressure rise (dP/dt)_max and deflagration index K_st, of lauric acid and stearic acid dust clouds was experimentally investigated. A synchronous thermal analyser was used to test the particle thermal characteristics. The functional test apparatuses including the 1.2 L Hartmann-tube apparatus, modified Godbert-Greenwald furnace, and 20 L explosion apparatus were used to test the explosion parameters. The results indicated that the rapid and slow weight loss processes of lauric acid dust followed a one-dimensional diffusion model (D1 model) and a 1.5 order chemical reaction model (F1.5 model), respectively. In addition, the rapid and slow weight loss processes of stearic acid followed a 1.5 order chemical reaction model (F1.5 model) and a three-dimensional diffusion model (D3 model), respectively, and the corresponding average apparent activation energy E and pre-exponential factor A were larger than those of lauric acid. The stearic acid dust explosion had higher values of MIE and MIT, which were mainly dependent on the higher pyrolysis and oxidation temperatures and the larger apparent activation energy E determining the slower rate of chemical bond breakage during pyrolysis and oxidation. In contrast, the lauric acid dust explosion had a higher MEC related to a smaller pre-exponential factor A with a lower amount of released reaction heat and a lower heat release rate during pyrolysis and oxidation. Additionally, due to the competition regime of the higher oxidation reaction heat release and greater consumption of oxygen during explosion, the explosion pressure P_m of the stearic acid dust was larger in low concentration ranges and decayed to an even smaller pressure than with lauric acid when the concentration exceeded 500 g/m³. The rate of explosion pressure rise (dP/dt)_m of the stearic acid dust was always larger in the experimental concentration range. The stearic acid dust explosion possessed a higher P_max, (dP/dt)_max and K_st mainly because of a larger pre-exponential factor A related to more active sites participating in the pyrolysis and oxidation reaction. Consequently, the active chemical reaction occurred more violently, and the temperature and overpressure rose faster, indicating a higher explosion hazard class for stearic acid dust.     

钢渣吸附-微波降解法处理碱性品红废水

研究了钢渣对碱性品红染料的吸附性能、影响因素以及微波对吸附在钢渣-焦炭上的染料的降解作用。实验表明,在中性条件下,钢渣对碱性品红具有优良的吸附性能,饱和吸附量可达到42．4mg／g。以钢渣处理质量浓度为100mg/L的碱性品红溶液,当固液质量比为1：50、振荡吸附1h后,染料溶液脱色率达97％。实验还表明,焦炭可吸收微波产生高温,用钢渣-焦炭混合物（质量比1：1）吸附染料后,以微波辐照可使物料达到665℃的高温,吸附的染料降解。吸附剂再生后重复使用4次,脱色率都达到95％以上。     

城市生活垃圾热解产气特性的试验研究

在外热式固定床试验台上,针对城市生活垃圾中的典型组分,进行了不同条件下的热解试验研究。试验测量不同条件下产物的产气量和产气速率,分析了热解气的组分和气体热值。分析发现,物料的挥发分、加热方式以及热解终温等对产气影响大,随温度的增加产气中H2含量逐渐增多,C2H4和C2H6的含量逐渐下降,气体热值有一个最大值。     

微波消解-流动注射分光光度法测定总氮和总磷

以碱性过硫酸钾溶液为消解液,采用微波消解-流动注射分光光度法测定水中总氮和总磷。在碱性过硫酸钾溶液中氢氧化钠质量浓度为9.6g/L、微波功率为320W、消解管长度为16m的条件下,总氮和总磷的检出限分别为0.040m g/L和0.020mg/L,线性范围分别为0.040～3.500mg/L和0.020～2.500mg/L,相对标准偏差分别为1.6%和1.0%。微波消解-流动注射分光光度法应用于河水、湖水、化工废水等实际水样中总氮和总磷的测定,加标回收率分别为95.7%～98.1%和97.2%～102.2%。     

模拟医疗废物在TG-DTA-FTIR上的热失重特性研究

在热重-差热分析仪上对模拟医疗废物分别在氮气和空气气氛中不同升温速率下加热的热失重行为进行了研究,并对升温速率和不同气氛对其热失重行为的影响进行了探讨.结果表明,随升温速率的提高,模拟医疗废物在2种气氛下热失重时挥发分初析出温度（T_s）向高温方向偏移、失重速率峰值（DTG_max）显著增大;在氮气气氛下,物料热失重时有2个失重峰,前后2个峰的失重率分别为31%和59%左右,在空气气氛下,有3个失重峰,前2个峰失重率分别在44%～59%和31%～46%之间.同时,结合同步傅立叶变换红外光谱仪对各个条件下的气体产物进行了定性分析,并对其中的CO、CO₂、H₂O和CH₄进行了定量分析.实验发现,模拟医疗废物在2种气氛下热失重主要阶段的产物种类相似,都检测到了CO₂、CO、烷烃类、醛类、羧酸、醇类和烯烃的特征吸收峰.并且,结果显示升温速率和气氛条件对CO、CO₂、H₂O和CH₄的生成量都有影响.在热失重的主要阶段,水分含量随加热时间变化曲线上显示1个向下的峰,说明载气中原有水分参与了反应.     

生物质废弃物快速热解制取富氢气体的实验研究

采用管式炉对红松锯屑快速热解制取富氢气体进行了实验研究,分析了反应器温度、物料粒径和催化剂对热解产物组成的影响.结果表明高温能加快生物质快速热解进程,减少炭和焦油生成量,利于富氢气体的生成,800℃时气态产物比例可达56.9 wt.%,气态产物中H2体积分数由4.3%(500℃下)上升至17.2%,H2 CO体积分数达68.3%.小粒径能增大热解气态产物的比例,但对气态产物组成的影响很小,这可能与红松锯屑本身质地疏松有关.以与生物质直接混合方式添加的煅烧白云石能使热解产物中H2含量增加,但造成产气过程变缓,炭生成量增多,富氢气体总产量未能得到提高.     

微波消解-分光光度法测定COD的研究

通过试验研究,提出了测定COD的新方法——微波消解-分光光度法。该方法准确度、精密度符合分析要求,与国标中回流法的测定结果没有显著差异。而且采用该方法测定COD可克服回流法、微波消解-滴定法及HACH-COD测定法的操作复杂、耗时长等缺点。     

耐候钢中微量元素的测定

本文分别用化学法和电感耦合等离子体发射光谱法(ICP-AES)测定了Corten-B和Sten3两种耐候钢中Cr、Cu、Mn、Sb、Si、V、P、Ti等8种微量元素的含量,并与传统的化学法进行了对比.试验证明ICP-AES光谱法不但技术简便、快速、易于推广应用,而且ICP-AES光谱法和微波消解技术联用在微量元素测量上有更准确、安全等方面的优点.另外,ICP-AES仅通过对少量样屑的一次溶样即可得到全部元素的分析结果,节省了钢样,这对于难以取样的情况尤为有利.     

微波消解-原子荧光法测定海洋沉积物中As的研究

研究了微波消解海洋沉积物中的As,在比较几种不同的酸消解体系后,得到适合海洋沉积物分析的酸消解体系.与传统的湿法消解比较,测试结果无显著性差异.微波消解具有快速高效、试剂用量少、空白值低、样品不易挥发等优点,已成为海洋沉积物样品前处理的有效手段.     

聚氨酯泡沫材料阴燃发展过程的特性分析

分析对比了相同加热条件下的聚氨酯泡沫材料在有氧和无氧气氛下的升温过程,并对不同加热条件下的聚氨酯泡沫材料的阴燃传播速度进行研究.结果表明:沿着反应进行的方向,分离点的温度越来越低,不同热流条件下的温度分离曲线斜率在实验稳定发展段的变化规律表现得很相似,并在分离点出现后,有氧气氛中的该位置温度在短时间内急剧上升;在阴燃不稳定传播阶段时,热解前锋的速度小于氧化前锋的速度,在稳定传播阶段时,热解前锋速度与氧化前锋速度近乎相等.