稻壳活性炭制备及其对磷的吸附

利用农业废弃物稻壳经炭化、活化、酸洗、水洗和干燥等工艺制备出一种富含微孔和中孔结构的稻壳活性炭,其BET比表面积达886.3 m2/g。通过正交实验优化了稻壳活性炭对磷吸附条件,并在该条件下进行了吸附等温和吸附动力学实验研究。结果表明,稻壳活性炭对磷的吸附等温曲线能较好符合Langmuir模型(R2=0.9284)和Freundlich模型(R2=0.9208),由Langmuir线性拟合方程可得稻壳活性炭对磷饱和吸附量达6.93 mg/g;稻壳活性炭对磷的吸附过程可用准二级动力学方程描述(R2=0.9968),吸附速度较快,颗粒内扩散为该过程控速阶段。稻壳活性炭作为一种易得、廉价、高效的填料,在农村分散型污水生态处理技术中,具有良好的应用前景。     

不锈钢烧结纤维毡外加粉体助剂过滤烟尘微粒

为了解决不锈钢烧结纤维毡对柴油机微粒过滤效率不高及其黏附堵塞问题,提出了不锈钢烧结纤维毡外加粉体助剂过滤烟尘的新方法。用不同过滤精度(5～30μm)的不锈钢烧结纤维毡片,覆盖不同厚度(0.5～3 mm)的粉体层,对由发烟剂燃烧产生的烟尘(D50=0.183μm)进行了过滤实验,用welas3000气溶胶粒径谱仪测试过滤前后的烟尘浓度,得到了不同情况下的过滤效率及分级效率。实验结果表明,粉体粒径、厚度、过滤气速及时间对过滤效率影响都很大,在滤速3 m/min、粉体粒径200～250目及厚度1.5 mm时,初始过滤效率高达95.746%,30 min后过滤效率上升到98.499%,300min内过滤效率基本保持在98%以上。     

牡蛎壳粉末投加UASB反应器的运行特性

采用牡蛎壳粉末作为UASB反应器的辅助介质,探讨了牡蛎壳钙盐的溶出特性,系统考察了运行期中牡蛎壳粉末添加方式、进水有机负荷、水力停留时间等因素对反应器出水COD、碱度与pH的影响,分析了污泥比产甲烷活性变化。结果表明,当初始pH从5到9变化时,牡蛎壳粉末溶出Ca2+浓度为40~65 mg/L,平衡pH稳定在7.7~8.0;当进水COD负荷从3.4 kg/(m3·d)逐渐增至7.0 kg/(m3·d)、牡蛎壳粉末投加量从1.5 g/d逐渐增至3.2 g/d时,与未投加的反应器相比,投加牡蛎壳粉末反应器的启动周期缩短了10%左右,COD去除率与比产甲烷活性分别提高了13.3%和22%。投加牡蛎壳粉末可有效提供碱度,加快污泥的颗粒化进程。     

双套管长距离气力输送技术的应用

介绍了北仑发电厂5×600 MW机组烟气脱硫项目石灰石粉双套管长距离气力输送工程的系统设计、安装、调试、运行等情况,并分析了该系统的主要特点.     

焦粉活性炭的制备及其应用

用废弃焦粉制备焦粉活性炭，通过正交实验考察了各种因素对焦粉活性炭性能的影响。实验结果表明：在活化时间80min、活化温度900℃、碱炭比（氢氧化钾与废弃焦粉的质量比）4、废弃焦粉粒径小于0．05mm的最佳条件下，制备的焦粉活性炭的亚甲基蓝吸附值为304．8mg／g，产率为35．6％；废弃焦粉的活化是活化剂刻蚀其颗粒形成丰富孔结构的氧化还原反应过程；用最佳条件下制备的焦粉活性炭处理质量浓度为60mg／t．的模拟含Cr^6＋废水，在废水pH为3—4、焦粉活性炭加入量为4g/L、吸附时间为50min的条件下，Cr^6＋去除率达93．2％。     

超音速气流粉碎机生产超细粉体的安全问题探讨

超音速气流粉碎机是一种常用的生产超细粉体的设备。粉碎过程中涉及到许多安全问题，如粉尘的危害，噪音危害等。本文根据安全系统工程理论。从除尘器的选择、防护和管理措施的实施等方面对治理粉尘危害进行了探讨。     

Synthesis of highly effective absorbents with waste quenching blast furnace slag to remove Methyl Orange from aqueous solution

Water quenching blast furnace slag(WQBFS) is widely produced in the blast furnace iron making process. It is mainly composed of CaO, MgO, Al_2O_3, and SiO_2 with low contents of other metal elements such as Fe, Mn, Ti, K and Na. In this study, WQBFS was treated with grinding, hydrochloric acid acidification, filtration, filtrate extraction by alkali liquor and a hydration reaction. Then BFS micropowder(BFSMP), BFS acidified solid(BFSAS) and BFS acid-alkali precipitate(BFSAP) were obtained, which were characterized by X-ray diffraction, scanning electron microscopy, X-ray fluorescence and Brunauer-Emmet-Teller(BET)specific surface area. The decoloration efficiency for Methyl Orange(MO) was used to evaluate the adsorptive ability of the three absorbents. The effects of adsorptive reaction conditions(p H and temperature of solution, reaction time, sorbent dosage and initial concentration) on MO removal were also investigated in detail. The results indicated that BFSAP performed better in MO removal than the other two absorbents. When the p H value of MO solutions was in the range 3.0–13.0, the degradation efficiency of a solution with initial MO concentration of 25 mg/L reached 99.97% for a reaction time of 25 min at 25°C.The maximum adsorption capacity of BFSAP for MO was 167 mg/g. Based on optimized experiments, the results conformed with the Langmuir adsorption isotherm and pseudo-second-order kinetics. Among inorganic anions, SO_4~(2-)and PO_4~(3-)had significant inhibitory effects on MO removal in BFSAP treatment due to ion-exchange adsorption.     

Levels of organochlorine pesticides in human milk from central Taiwan

The present study determined the residues of organochlorine pesticides (OCPs) in human milk collected in central Taiwan between December 2000 and November 2001. The OCPs were analyzed by GC/MS for 36 human milk samples from healthy women ranging between 20 and 36 years of age. The predominant OCPs were p,p′-DDE, p,p′-DDT, -CHL, heptachlor epoxide, heptachlor, β-HCH, and γ-HCH, with median levels of 228, 19, 7.4, 4.0, 2.3, 1.2, and 0.8 ng/g lipid, respectively. The residues of OCPs in human milk from central Taiwan were comparable to those described in results from Sweden, the United Kingdom, and Japan, and were significantly lower than those from investigations in Asian countries, including China, Thailand, Indonesia, and Vietnam. Low DDE/DDT ratio (mean = 13.6, SD = 6.54) indicated that residual OCPs in human milk mainly originate from past exposure. A notable decrease in DDT levels (∑ DDT = 333 ng/g lipid) in human milk was found in this study compared to results from the previous two decades (∑ DDT = 3595 ng/g lipid). Hypothetically, the level of -CHL was significantly associated with total TEQ levels in Taiwanese human milk because of the sources of food contaminant, i.e. animal fat. Based on low OCP levels in Taiwanese human milk and low estimated median daily intake of total DDTs for a breastfed infant (1358 ng/kg/day) with the assumption of an infant weighting 4 kg and consuming 699 g milk per day in the first month after birth, the Taiwanese policy of breast-feeding promotion was supported.     

Characteristics of mercury emission from linear type of spent fluorescent lamp

In order to recycle the linear type of SFL (spent fluorescent lamp), mercury from SFL should be controlled to prevent leaking into the environment. For mercury emission from SFL, mercury concentration is estimated in the parts of SFL such as glass tube, phosphor powder, and base cap using the end-cutting unit. It is also evaluated mercury emission in the effluent gas in the end-cutting unit with changing flow rate. From the results of mercury emission from SFLs, phosphor powder has greater than 80% of mercury amount in SFL and about 15% of mercury amount contained in glass tube. The initial mercury concentration in vapor phase is almost decreased linearly with increasing airflow rate from 0.7 L/min to 1.3 L/min. It is desirable that airflow rate should be high until the concentration of mercury vapor will be stable because the stabilized concentration becomes to be low and the stabilized time goes to be short as increased airflow rate. From KET and TCLP results, finally, phosphor powder should be managed as a hazardous waste but base-cap and glass are not classified as hazardous wastes.     

Pyrolysis characteristics of the mixture of printed circuit board scraps and coal powder

Thermogravimetric (TG) analysis and infrared spectroscopy were used to analyze the pyrolysis characteristics of printed circuit board scraps (PCBs), coal powder and their mixtures under nitrogen atmosphere. The experimental results show that there is a large difference between waste PCBs and coal powder in pyrolysis processing. The pyrolysis properties of the mixing samples are the result of interaction of the PCBs and coal powder, which is influenced by the content of mixture. The degree of pyrolysis and pyrolysis properties of the mixture are much better than that of the single component. The TG and the differential thermogravimetric (DTG) curves of the PCBs mixed with coal powder move towards the high-temperature zone with increasing amount of coal powder and subsequently the DTG peak also becomes wider. The Coats–Redfern integral method was used to determine the kinetic parameters of pyrolysis reaction mechanism with the different proportion of mixture. The gas of pyrolysis mainly composes of CO₂, CO, H₂O and some hydrocarbon. The bromide characteristic absorption peak has been detected obviously in the pyrolysis gas of PCBs. On the contrary, the absorption peak of the bromide is not obvious in pyrolysis gas of the PCBs samples adding 40% coal powder.