北京夏季灰霾天臭氧近地层垂直分布与边界层结构分析

后奥运时期首都北京的空气质量被更加关注,尤其是对于灰霾天与光化学复合污染的状况,而近地层数百米高度内的大气污染物与大气物理参数垂直分布观测对于空气质量变化过程评估至关重要.因此,本研究于2009年8月1-16日,在北京市325 m气象塔进行了相应的立体观测,观测平台垂直分布在距离地面高度8、47、120和280 m四层中.同时,在近地面320 m高度以内,分15层分别观测了大气温度、湿度、风速、风向.另外,使用气溶胶后向散射云高仪观测了边界层2.5 km内气溶胶后向散射系数.利用垂直分层的O3数据与边界层物理观测数据并结合天气形势、后向轨迹模式等方法,综合分析了本次观测数据之间的相互关系和内在联系.结果表明:夏季西北部低压槽控制的北京区域不利于低空大气扩散,容易形成光化学污染叠加灰霾污染,污染形成时白天地面小时最大φ(O3)可达120×10-9,280 m高度处可达155×10-9;来自西北偏西的气流一般较为干净,有利于北京污染物的清除,而来自西南和偏南的气流使北京的O3污染加重,导致区域性高浓度O3污染;在稳定天气条件下,夜间残留层与地面的φ(O3)差别越大,次日光化学生成的φ(O3)起点越高,表明残留层O3在次日混合层抬升过程中卷夹到地面,影响地面空气质量;300 m以内的近地层,在50 m高度左右存在φ(O3)变化程度剧烈层,这是城市冠层界面与大气化学反应共同作用的结果.     

我国典型钢铁行业主要工艺环节排放颗粒物源成分谱特征

鉴于我国钢铁行业排放颗粒物源成分谱数量不足,有待更新的现状,致力于服务精细化颗粒物源解析的需求,采用稀释通道系统对武汉市某钢铁公司的3个主要工艺环节(烧结、炼钢、炼铁)排放源进行了采样.构建了3类PM_(2.5)源成分谱及3类PM_(10)成分谱,对源谱主要化学组分特征进行了研究,并与国内其他区域已有的钢铁行业源谱研究进行了对比.结果表明:(1)烧结工艺源成分谱中,SO_4~(2-)、Al和NH_4~+等含量高,PM_(2.5)源谱中质量分数依次为22. 2%、4. 5%和3. 5%,PM_(10)源谱中依次为36. 0%、5. 2%和2. 7%,炼铁工艺Fe元素含量最高,在PM_(2.5)源谱和PM_(10)源谱中分别达到28. 3%和24. 5%,炼钢工艺源谱Ca、Fe元素等为主要组分;(2)元素组分中,烧结工艺S元素含量最高,地壳元素在PM_(10)源谱中含量更高,炼铁工艺Pb、Cr等重金属含量偏高,炼钢工艺Cr富集;(3)源谱之间分歧系数的计算显示,同类工艺粗细粒径源谱相似性偏高,烧结工艺与其他两类工艺源谱之间差异性较高,炼钢工艺与炼铁工艺差异性较低.同国内其他区域研究源谱相比,发现Fe、Si和Ca等为钢铁行业排放颗粒物中标识性组分,而碳组分和SO_4~(2-)等组分特征随生产方式、除污设备等不同表现出不同特征.     

Identification of odorous compounds in reclaimed water using FPA combined with sensory GC-MS

Odorous compounds in the influent of a reclaimed water treatment plant (RWTP), consisting of coagulation, sedimentation, continuous micro-filtration (CMF), and chlorination in succession, in a north China city, were identified by combining flavor profile analysis (FPA) with sensory gas chromatograph-mass spectrometry (GC-MS). The sewery/swampy/septic odor with an odor intensity of 6.4 was found to be the major odor group in the RWTP influent, and the existence of well-known odorant including dimethyl disulfide, dimethyl trisulfide, indole and skatole were confirmed using GC-MS. The result of a spiking test showed that the intensity (3.6) of the sewery/swampy/septic odor caused by these four chemicals contributed to over 50% of the odor intensity of the influent. The FPA intensity for sewery/swampy/septic odor in the RWTP effluent was 3.8, showing that the treatment process was not efficient for the removal of odorants, particularly indole and skatole.     

餐饮源油烟中PM2.5的化学组分特征

集中分析了餐饮无组织排放源(街边小吃、火锅店、露天烧烤)及有组织排放源(10家大中型餐馆)油烟PM_2.5中的TC(总碳)、元素组分、离子组分和16种PAHs,得到了各类餐饮源油烟PM_2.5的化学组成特征,建立了餐饮源油烟化学成分谱. 结果表明:各餐饮源油烟的ρ(PM_2.5)是大气背景值的3~42倍,其中露天烧烤油烟的ρ(PM_2.5)最高,达5 659.8 μg/m3. 不同餐饮源油烟的PM_2.5中各化学组分均为w(TC)(38.1%~75.8%)＞w(元素组分)(4.5%~27.0%)＞w(离子组分)(2.7%~22.6%),并且ρ(PM_2.5)与w(TC)呈显著正相关(R=0.84). 菲(PHE)、芘(PYR)、荧蒽(FLT)的质量分数在各类餐饮源油烟的PAHs中均普遍较高,分别为13.8%~21.6%、9.2%~26.5%、6.9%~22.0%.大中型餐馆油烟的PAHs中苯并苝(BPE)的质量分数最高(27.5%),而在其他餐饮源中均小于6.7%;(CHR)的质量分数最低(3.3%),而在其他餐饮源中均大于5.3%. 露天烧烤油烟的PAHs中芘、荧蒽的质量分数分别是其他餐饮源的2.7和2.3倍以上;萘(NAP)的质量分数(0.3%)较小,但在其他餐饮源中均大于11.4%,可以作为特定餐饮源油烟的特征物种.      

地铁型材模具的探讨

介绍了大型铝型材的特点 ,大型铝型材模具的设计 ,分流比的选择 ,分流孔位置的布置 ,芯头颈部的选择 ,工作带的确定以及加工中的注意事项     

岷江上游干旱河谷区褐土不同亚类剖面及养分特征

研究了岷江上游干旱河谷区典型地段海拔梯度上褐土的3种亚类土壤剖面及其养分特征．岷江上游干旱河谷褐土粘化作用较弱，矿物风化程度低；土壤呈碱性，pH值为7．0-9．0，富含碳酸钙的石灰性褐土达8．0-9．0；土壤表层有机质w在32．55-72．78g／kg，整个土壤剖面中全氮w0．78-4．00g／kg，全磷w0．33-0．68g／kg，全钾18．24-21．68g／kg．总的来说，褐土潜在肥力水平较高，但由于土壤水分条件的限制，土壤潜在性肥力向有效性肥力转化的能力较差，致使土壤有效性肥力水平较低．其中，土壤有效氮和有效钾w分别为25．57-24．46g／kg和研8．24-1453．65g／kg，同时由于土壤pH值和碳酸钙w较高，土壤中磷的固定较多，使得土壤有效磷w尤其偏低，为1．10-21．20g／kg．干旱河谷高海拔地区的淋溶淀积型褐土的肥力水平高于中海拔地区的石灰性褐土，低海拔地区的燥褐土肥力水平最低．土壤肥力随海拔高度升高而递增，决定了干旱河谷植被恢复从高海拔地区向低海拔地区更容易进行．表3参13     

Shifted power-law relationship between NO2 concentration and the distance from a highway: A new dispersion model based on the wind profile model

In this paper, a shifted power-law model, based on the wind profile model, had been supposed to simulate concentration gradient of nitrogen dioxide (NO₂) with distance from a highway. Field experiments were performed for NO₂ gradients from a highway in Shanghai by using passive samplers. The shifted power-law model was fitted well with experimental results of field experiments both in this study and in the literature. The results not only verified the validity of shifted power-law relationship between NO₂ concentration and the distance from a highway, but also partially demonstrated that there were some significant similarities between wind profile and air pollutants concentration profile near highway. With known concentration of chosen reference point and appropriate value of the parameter k, the model could be practically applied for predicting the NO₂ distributions near a highway. The methods of determining the parameter k were also discussed for further detailed studies.     

Profiles of PAH emission from steel and iron industries

In order to characterize the polycyclic aromatic hydrocarbons (PAHs) emission from steel and iron industries, this study measured the stack emission of twelve steel and iron plants in southern Taiwan to construct a set of source fingerprints. The study sampled the emissions by the USEPA's sampling method 5 with the modification of Graseby for the gas and particulate phase PAH and, then, used Hewlett-Packard 5890 gas chromatograph equipped with mass spectrometer detector to analyze the samples. The steel and iron industries are classified into three categories on the basis of auxiliary energy source: Category I uses coal as fuel, Category II uses heavy oil as fuel and Category III uses electric arc furnace. The pollution source profiles are obtained by averaging the ratios of individual PAH concentrations to the total concentration of 21 PAHs and total particulate matter measured in this study. Results of the study show that low molecular weight PAHs are predominant in gas plus particulate phase for all three categories. For particulate phase PAHs, however, the contribution of large molecular weight compounds increases. Two-ring PAHs account for the majority of the mass, varying from 84% to 92% with an average of 89%. The mass fractions of 3-, 4-, 5-, 6-ring PAHs in Category I are found to be more than those of the other two categories. The mass of Category III is dominated by 7-ring PAHs. Large (or heavy) molecular weight PAHs (HMW PAHs) are carcinogenic. Over all categories, these compounds are less than 1% of the total-PAH mass on the average. The indicatory PAHs are benz[a]anthracene, benzo[k]fluoranthene, benzo[ghi]perylene for Category I, benzo[a]pyrene, acenaphthene, acenaphthylene for Category II and coronene, pyrene, benzo[b]chrycene for Category III. The indicatory PAHs among categories are very different. Thus, dividing steel and iron industry into categories by auxiliary fuel is to increase the precision of estimation by a receptor model. Average total-PAH emission factors for coal, heavy oil and electric arc furnace were 4050 μg/kg-coal, 5750 μg/l-oil, 2620 μg/kW h, respectively. Carcinogenic benzo[a]pyrene for gas plus particulate phase was 2.0 g/kg-coal, 2.4 μg/l-oil and 1.4 μg/kW h for Category I, II and III, respectively.     

Robust benchmark dose determination based on profile score methods

We investigate several methods commonly used to obtain a benchmark dose and show that those based on full likelihood or profile likelihood methods might have severe shortcomings. We propose two new profile likelihood-based approaches which overcome these problems. Another contribution is the extension of the benchmark dose determination to non full likelihood models, such as quasi-likelihood, generalized estimating equations, which are widely used in settings such as developmental toxicity where clustered data are encountered. This widening of the scope of application is possible by the use of (robust) score statistics. Benchmark dose methods are applied to a data set from a developmental toxicity study.     

水环境中耐热大肠菌群的抗生素耐药性与质粒谱研究

用滤膜法、mFC培养基从5种水体中分离出疑似耐热大肠菌162株,用API微生物分析系统鉴定到种,以Kirby-Bauer法分析其对人畜常用10种抗生素的耐药性,碱裂解法小量制备各菌株质粒DNA做质粒谱分析.结果表明,埃希氏大肠杆菌为优势菌,占分离菌总数的96.3%.除分离自泉水的3株外,其它菌株都对3种及3种以上抗生素耐药,多重耐药率为98.1%.不同水体分离菌株对氧氟沙星、诺氟沙星、庆大霉素、丁胺卡那霉素、链霉素的耐药率有显著性差异(P<0.005).92株菌(56.8%)提取到大小为0.90～158.83kb、数量为1～6个的质粒,有81种质粒谱型.70株(43.2%)未提取到质粒的细菌中有67株为多重耐药.具有相同质粒谱型的菌株耐药谱都不相同.未发现质粒谱与抗生素耐药性间有明显相关性.图1表3参15