近断层地震动考虑能量损伤效应的非弹性强度需求

由于靠近断层处地震地面运动中速度脉冲作用的存在,导致传统的基于瞬时加速度反应谱的抗震设计,不能有效考虑由此带来的巨大能量耗散和位移需求。笔者采用代表性的脉冲型实际近场地震记录和人工模拟三角函数地震动时程,在分析累积输入地震动耗能和结构位移间关系基础上,提出了等效速度比的表达式;给出了近场地震动的等效变形需求表达式;提出了等价延性系数的概念,来考虑由于地震动能量耗散对结构的强度需求;经非线性时程分析方法对其稳定性进行了验证比较,有利于增强结构的安全性。     

农用改性硝酸铵拒爆机理及工业化可行性研究

对农用硝铵作改性处理,通过筛选和优化实验确定了改性硝酸铵配方。结果表明,当硝酸铵中添加3%的改性剂GXJ1,10%的改性剂GXJ2时,产品在1mm铁皮管约束下的雷管感度试验条件下具有拒爆特性。改性硝酸铵总养分与普通硝酸铵相当,并且颗粒强度高,不易粉化、结块和吸潮,具有优良的肥料品质。同时还利用X射线衍射分析、扫描电子显微镜分析对改性硝铵的拒爆机理作初步探讨。最终,建立了改性硝酸铵的脱水性能、流动性能、凝固性能、颗粒强度的评价方法,并进行了工业化可行性研究。     

电石渣浆处理与资源化

针对电石渣浆处理的工艺流程和资源化途径进行了效益分析,工程实践表明:电石渣浆处理后,浆水回用作为生产用水,降低了乙炔生产成本.同时彻底解决电石渣含水率高的问题,利于企业开展资源化,值得在乙炔行业推广.     

大力发展循环经济促进宁阳县可持续发展

宁阳县发展循环经济过程中所取得的初步成果,同时对当前存在的突出问题,提出了相应的对策和改进措施:制定促进循环经济发展的相关政策;构筑循环经济基本模式,推动建立生态工业园;建立循环经济发展的技术支撑体系;制定发展循环经济的长远规划;提高全民发展循环经济意识和公众参与水平.     

A hybrid decision-making approach based on FCM and MOORA for occupational health and safety risk analysis

IntroductionWith the development of industries and increased diversity of their associated hazards, the importance of identifying these hazards and controlling the Occupational Health and Safety (OHS) risks has also dramatically augmented. Currently, there is a serious need for a risk management system to identify and prioritize risks with the aim of providing corrective/preventive measures to minimize the negative consequences of OHS risks. In fact, this system can help the protection of employees’ health and reduction of organizational costs. Method: The present study proposes a hybrid decision-making approach based on the Failure Mode and Effect Analysis (FMEA), Fuzzy Cognitive Map (FCM), and Multi-Objective Optimization on the basis of Ratio Analysis (MOORA) for assessing and prioritizing OHS risks. After identifying the risks and determining the values of the risk assessment criteria via the FMEA technique, the attempt is made to determine the weights of criteria based on their causal relationships through FCM and the hybrid learning algorithm. Then, the risk prioritization is carried out using the MOORA method based on the decision matrix (the output of the FMEA) and the weights of the criteria (the output of the FCM). Results: The results from the implementation of the proposed approach in a manufacturing company reveal that the score at issue can overcome some of the drawbacks of the traditional Risk Priority Number (RPN) in the conventional FMEA, including lack of assignment the different relative importance to the assessment criteria, inability to take into account other important management criteria, lack of consideration of causal relationships among criteria, and high dependence of the prioritization on the experts’ opinions, which finally provides a full and distinct risk prioritization.     

Performance evaluation of reverse logistics enterprise – an agent-based simulation approach

Reverse logistics (RL) has been applied in many industries and sectors since its conception. Unlike forward logistics, retracing consumer goods from the point of consumption to the point of inception is not a well-studied process. It involves many uncertainties such as time, quality and quantity of returns. The returned products can be remanufactured, have parts harvested, or be disposed safely. It is important to implement these activities in a cost-effective manner. The aim of this research is to measure the performance of the RL enterprise with the help of an agent-based simulation model. The major entities in the RL network are considered as Agents that can act independently. There are several different agents: collector agent, sorting-cum-reuse agent, remanufacturing agent, recycler agent, supplier agent and distributor agent. The individual performances of the agents are measured and recommendations are given to improve their performance, leading to the enhancement of the total performance of the RL enterprise. The approach is applied to a case study involving cell phone remanufacturing.     

Nitrogen evolution during the co-combustion of hydrothermally treated municipal solid waste and coal in a bubbling fluidized bed

Nitrogen evolution was studied during the co-combustion of hydrothermally treated municipal solid wastes (HT MSW) and coal in a bubbling fluidized bed (BFB). HT MSW blending ratios as 10%, 20% and 30% (wt.%) were selected and tested at 700, 800, 900 °C. Emissions of NO and N₂O from blends were measured and compared with the results of mono-combustion trials. Moreover, concentrations of precursors like NH₃ and HCN were also quantified. The results are summarized as follows: NO emissions were predominant in all the cases, which rose with increasing temperature. The blending of HT MSW contributed to the NO reduction. N₂O emissions decreased with temperature rising and the blending of HT MSW also presented positive effects. At 30% HT MSW addition, both NO and N₂O emissions showed the lowest values (391.85 ppm and 55.33 ppm, respectively at 900 °C). For the precursors, more HCN was detected than NH₃ and both played important roles on the gas side nitrogen evolution.     

Recycling-oriented characterization of plastic frames and printed circuit boards from mobile phones by electronic and chemical imaging

This study characterizes the composition of plastic frames and printed circuit boards from end-of-life mobile phones. This knowledge may help define an optimal processing strategy for using these items as potential raw materials. Correct handling of such a waste is essential for its further “sustainable” recovery, especially to maximize the extraction of base, rare and precious metals, minimizing the environmental impact of the entire process chain. A combination of electronic and chemical imaging techniques was thus examined, applied and critically evaluated in order to optimize the processing, through the identification and the topological assessment of the materials of interest and their quantitative distribution. To reach this goal, end-of-life mobile phone derived wastes have been systematically characterized adopting both “traditional” (e.g. scanning electronic microscopy combined with microanalysis and Raman spectroscopy) and innovative (e.g. hyperspectral imaging in short wave infrared field) techniques, with reference to frames and printed circuit boards. Results showed as the combination of both the approaches (i.e. traditional and classical) could dramatically improve recycling strategies set up, as well as final products recovery.     

锆-十六烷基三甲基氯化铵改性活性炭对水中硝酸盐和磷酸盐的吸附特性

采用锆(Zr)和阳离子表面活性剂十六烷基三甲基氯化铵(CTAC)对活性炭进行联合改性,考察了所制备的Zr-CTAC改性活性炭对水中硝酸盐和磷酸盐的吸附去除作用,并探讨了相关的吸附去除机制.结果表明,Zr-CTAC改性活性炭对水中硝酸盐和磷酸盐均具备较好的吸附去除能力.Zr-CTAC改性活性炭对硝酸盐和磷酸盐吸附动力学过程满足准二级动力学模型.Langmuir、Freundlich和Dubinin-Radushkevich(D-R)等温吸附模型可以较好地描述Zr-CTAC改性活性炭对水中硝酸盐的等温吸附过程,Langmuir和D-R等温吸附模型可以较好地描述Zr-CTAC改性活性炭对水中磷酸盐等温吸附过程,通过Langmuir模型计算得到吸附剂对硝酸盐和磷酸盐的最大单位吸附量分别为7.58 mg·g-1和10.9 mg·g-1.高的p H会抑制Zr-CTAC改性活性炭对水中硝酸盐和磷酸盐的吸附.水中共存的Cl-、HCO-3和SO2-4等阴离子均会抑制Zr-CTAC改性活性炭对硝酸盐和磷酸盐的吸附,且对吸附硝酸盐的抑制作用较强而对吸附磷酸盐的抑制作用较弱.水中共存的磷酸盐对Zr-CTAC改性活性炭吸附硝酸盐的抑制作用较强,而水中共存的硝酸盐对Zr-CTAC改性活性炭吸附磷酸盐的抑制作用较弱.1 mol·L-1Na Cl溶液可以使90%左右被吸附到Zr-CTAC改性活性炭表面上的硝酸盐解吸下来.1 mol·L-1的Na OH溶液可以使78%左右被吸附到Zr-CTAC改性活性炭表面上的磷酸盐解吸下来.Zr-CTAC改性活性炭对硝酸盐的吸附机制主要包括阴离子交换作用和静电吸引作用,对磷酸盐的吸附机制主要包括配位体交换作用、阴离子交换作用和静电吸引作用.上述结果说明Zr-CTAC改性活性炭适合作为一种吸附剂去除废水中的硝酸盐和磷酸盐.     

不同运行模式下改良型CAST工艺处理生活污水的除磷性能

实验采用改良型CAST工艺,以生活污水为研究对象,考察了C/P、回流比及温度等不同运行模式对系统除磷性能的影响.结果表明,常温条件下进水C/P由50升至100,系统除磷率均值从15%迅速升至95.6%,除磷性能显著提高;继而降低C/P至75,除磷性能因进水碳源不足再度下降,除磷率均值为51.4%,且长期投加易降解碳源引发系统污泥膨胀并导致污泥大量流失.C/P较低情况下,回流比由25%降低至12.5%,除磷性能提高2.3倍,继续降低回流比至0,除磷性能反而下降;温度实验研究则表明,低温系统(14℃±1℃),除磷率稳定维持在90%以上,而高温短程硝化系统(27℃±1℃)除磷率仅为14.1%,可见低温更有利于系统磷的去除.吸磷小试发现,常温系统污泥以O_2、NO_3~-和NO_2~-为电子受体均能进行吸磷,而低温系统污泥能以O_2、NO_3~-为电子受体进行吸磷,高温系统污泥则仅能以O_2为电子受体进行少量吸磷.此外,实验还发现,系统短期闲置导致的污泥"饥饿"有利于系统除磷率的提高.