一种新型流管反应器的设计与表征

介绍了一种用于气溶胶生成机制研究的流管反应器（Jiao-FTR,J-FTR）的设计及表征.借助计算流体力学（CFD）模拟和实验测定,表征了不同进气结构和实验条件下反应器内流场的发展及稳定,移动进气管的喷射效应以及气体和颗粒物在反应器内的平均停留时间.结果表明,预混合段进气方式,主流流量,移动进气管结构及注入流量对J-FTR的流场发展以及气体和颗粒物的停留时间具有较大影响;J-FTR的预混合进气段具有使主流快速过渡为层流的优势,在对称进气条件下,当主流流量不超过8L/min,气流在进入主反应段之前可发展为稳定的层流;当移动进气管使用大内径的直管或径面十字型结构时,可以有效减小或避免移动进气管的喷射效应.以上结果不仅可为使用J-FTR开展大气化学和气溶胶生成机制研究提供重要的实验指导,也可为其他研究者设计FTR,进行流管实验提供借鉴.     

Role of nano-additive blended biodiesel on emission characteristics of the research diesel engine

The current experimental study is aimed to analyze the influence of single-walled Carbon Nano Tubes (CNT) on the emission characteristics of neem biodiesel-fueled (NBD-fueled) diesel engine and the results compared with conventional diesel. Experiments were conducted in a single-cylinder, 4-stroke, diesel engine with an eddy current dynamometer at a constant speed of 1500 rpm. Two samples of CNT are characterized and dispersed into 100% of the NBD in a mass fraction of 50 and 100 ppm using ultrasonicator, and the physicochemical properties were measured. Experimental results indicated that by adding CNT nanoparticles in NBD reduces its NO_x, HC, CO, and smoke emission by 9.2%, 6.7%, 5.9%, and 7.8%, respectively, at all load conditions.     

钢管混凝土柱温度场简化计算方法

钢管混凝土柱是建筑承重结构的重要组成部分,其耐火极限研究尤为重要。温度场计算作为抗火研究的基础,在保证精确度的前提下要做到简单实用,为高效的抗火设计提供有利条件。通过有限元软件ABAQUS模拟构件温度场,分析80种不同工况下圆、方形构件温度场分布特点,并考虑钢管厚度、截面尺寸等因素,提出了钢管及混凝土温度简化计算公式。通过试验数据、模拟数据对公式进行调校验证,结果表明计算精度满足工程设计要求。     

Prenatal screening and diagnosis of neural tube defects

This review article discusses prenatal screening and diagnosis of neural tube defects (NTD). High detection rates occur in countries operating ultrasound screening programmes because classical two-dimensional ultrasound cranial signs (lemon shaped head, banana cerebellum, ventriculomegaly) are important diagnostic clues to the presence of spina bifida. Careful evaluation of both the spine and a search for other abnormalities is warranted. Important prognostic information for spina bifida relates to the lesion level, with a “watershed” between L3 and L4 marking a very high chance of being wheelchair bound with the higher lesions. Three-dimensional ultrasound using multiplanar views can achieve diagnostic accuracy within one vertebral body in around 80% of patients. There are high rates of pregnancy termination for spina bifida in many European countries, but the use of new imagining techniques allow better prediction of outcome, and consequently a refinement of prenatal counselling. Copyright © 2009 John Wiley & Sons, Ltd.     

Nickel recovery from electronic waste II Electrodeposition of Ni and Ni–Fe alloys from diluted sulfate solutions

This study focuses on the electrodeposition of Ni and Ni–Fe alloys from synthetic solutions similar to those obtained by the dissolution of electron gun (an electrical component of cathode ray tubes) waste. The influence of various parameters (pH, electrolyte composition, Ni²⁺/Fe²⁺ ratio, current density) on the electrodeposition process was investigated. Scanning electron microscopy (SEM) and X-ray fluorescence analysis (XRFA) were used to provide information about the obtained deposits’ thickness, morphology, and elemental composition. By controlling the experimental parameters, the composition of the Ni–Fe alloys can be tailored towards specific applications. Complementarily, the differences in the nucleation mechanisms for Ni, Fe and Ni–Fe deposition from sulfate solutions have been evaluated and discussed using cyclic voltammetry and potential step chronoamperometry. The obtained results suggest a progressive nucleation mechanism for Ni, while for Fe and Ni–Fe, the obtained data points are best fitted to an instantaneous nucleation model.     

660MW机组烟气循环流化床干法脱硫塔入口气流分布的试验研究

以某火电厂2×660MW机组循环流化床干法脱硫气流模拟试验为研究对象，采用速度分布不均匀度的概念，详细研究各种工况下入口烟道导流形式对脱硫塔文丘里速度场分布的影响。研究表明。通过合理设置入口烟道的导流装置，可满足各种工况下CFB-FGD脱硫塔的文丘里管段和反应器段的气流均布，为干法脱硫大型化的气流分布试验研究提供借鉴。     

高峰矿提升机用钢丝绳无损检测方法的研究

介绍了利用漏磁场原理检测钢丝绳断丝 ,磁桥回路测量钢丝绳磨损信号 ,并实现在一个传感器中对上述多种缺陷的综合检测。在信号处理方面 ,结合不同信号特征 ,设计了相应的电路和处理软件 ,实现了缺陷的定量检测