Experimental Study of the Criteria of Flow Laminarization in Two-Dimensional Dense Gas Plumes

Laminarization of flow in a two-dimensional dense gas plume was experimentally investigated in this study. The plume was created by releasing CO₂ through a ground-level line source into a simulated turbulent boundary layer over an aerodynamically rough surface in a meteorological wind tunnel. The bulk Richardson number (Ri_*), based on negative plume buoyancy, plume thickness, and friction velocity, was varied over a wide range so that the effects of stable stratification on plume laminarization could be observed. A variety of ambient wind speeds as well as three different sizes of roughness arrays were used so that possible effects of roughness Reynolds number (Re_*) on plume laminarization could also be identified. Both flow visualization methods and quantitative measurements of velocity and intermittency of turbulence were used to provide quantitative assessments of plume laminarization.Flow visualization provided an overall picture of how the plume was affected by the negative buoyancy. With increasing Ri_*, both the plume depth and the vertical mixing were significantly suppressed, while upstream propagation of the plume from the source was enhanced. The most important feature of the flow revealed by visualization was the laminarization of flow in the lower part of the plume, which appeared to be closely related to both Ri_* and Re_*.Measurements within the simulated dense gas plumes revealed the influence of the stable stratification on mean velocity and turbulence intensity profiles. Both the mean velocity and turbulence intensity were significantly reduced near the surface; and these reductions systematically depended on Ri_*. The roughness Reynolds number also had considerable influence on the mean flow and turbulence structure of the dense gas plumes.An intermittency analysis technique was developed and applied to the digitized instantaneous velocity signals. It not only confirmed the general flow picture within the dense plume indicated by the flow visualization, but also clearly demonstrated the changes of flow regime with variations in Ri_* and Re_*. Most importantly, based on this intermittency analysis, simple criteria for characterizing different flow regimes are formulated; these may be useful in predicting when plume laminarization might occur.     

典型钢铁企业汞排放水平及排放特征研究

以某典型钢铁企业为研究对象,测定企业废气、废水、固废汞排放水平,并分析汞排放特征。研究表明,球团、烧结、高炉工艺废气排口烟尘中汞排放浓度和排放速率明显低于烟气;汞主要以气态形式排放,烧结工艺排口废气汞最高浓度分别是其他2个排口的7倍和3倍。球团、烧结、高炉、电炉四工艺环节中,烧结汞排放速率占四工艺汞排放速率总和的87%。半干法脱硫、氨法脱硫、石灰石石膏脱硫对废气中汞的去除效率分别为90.0%、78.7%和29.9%。企业废水排放未检出汞,脱硫产生固废汞含量明显高于除尘产生固废汞含量,脱硫灰汞含量是脱硫石膏的15倍。     

外力作用下管道内表面缺陷处裂纹扩展研究

为提高油气管道安全风险评估的准确性,以含内表面缺陷管道为研究对象,利用ABAQUS软件线弹性及弹塑性分析不同尺寸缺陷对裂纹萌生特征的影响;采用扩展有限元法,建立管道3点弯曲模型与全尺寸静载物理试验,并非线性拟合裂纹扩展尺寸,研究内表面缺陷处裂纹扩展情况.研究结果表明:内表面缺陷中心处极易萌生裂纹,随着缺陷尺寸的增大,裂...     

VPT511BF-SY多孔流速仪在烟气流量在线监测中的应用

针对目前国内基于单个探头的单点在线测试烟气流量与参比方法监测比对合格率不高的问题,提出一种新颖的基于平均差压皮托管法的多孔流速仪,通过对不同的安装位置及安装数量的多孔烟气流速仪的烟气在线流量监测结果与手工监测结果进行比对,验证在适当位置安装一定数量的多孔烟气流速仪可以确保与手工监测比对结果满足要求。     

便携式GC/MS热脱附法直接测定环境空气中挥发性有机物

采用便携式气相色谱/质谱联用热脱附法直接测定环境空气中的挥发性有机物,优化了试验条件。方法在5×10-9~100×10-9范围内线性良好,39种化合物的检出限为1.1μg/m3~19μg/m3,标准气体平行测定的RSD≤11.0%,回收率在80%~120%之间。     

顶空气相色谱法在测定水中三氯乙醛的应用

研究以DB-624交联石英毛细管柱分离,微电子捕获检测器-顶空气相色谱法测定水中三氯乙醛的应用,与以往的方法相比,准确可靠、省工省时省试剂,符合"绿色分析化学"的要求。最低检出限为0.2μg/L,标准偏差为0.028μg/L,相对标准偏差为6.0%,加标回收率为88.7%～109%。     

渤海排污口邻近海域异养细菌的组成与分布

对渤海4个重点监测排污口（北塘、大蒲河、弥河和虞河）邻近海域异养细菌的组成和分布进行了调查研究。结果表明,分离到的各排污口邻近海域的细菌隶属于变形菌门（Proteobacteria）、厚壁菌门（Firmicutes）、放线菌门（Acti-nobacteria）和拟杆菌门（Bacteroidetes）4个细菌类群,其中变形菌门的细菌最丰富。各排污口的优势菌有所不同,北塘、弥河2个采样点的优势菌分别为Bacillus sp．、Pseudoalteromonas sp．,大蒲河采样点的优势菌为Vibrio sp．和Oceanospirillum sp．,虞河采样点的优势菌为 Shewanella sp．和 Bacillus sp．。多维尺度分析表明,北塘和虞河采样点的细菌种群特征较相近,细菌种群分布特征可能与排污口的海洋环境有一定的相关性。     

催化燃烧处理有机废气及催化剂中毒的防止

研究了在Ｐｔ、Ｐｄ、Ｃｅ多组分蜂窝状催化剂上乙醇、环己烷和苯的氧化性能及水蒸气对催化剂活性的影响,探讨了如何防止硫化氢和甲硫醇引起的催化剂中毒。     

烟气脱碳技术进展

介绍了吸收法、吸附法、低温法、膜分离法回收烟道气中CO2的研究和应用现状,并对这些方法进行了比较,指出了适用范围。     

含氟废气对农业环境的影响

叙述了某厂氢氟酸生产过程排出的含氟废气对厂区周围水稻和蔬菜的污染及其与气象条件的关系，并提出了防止农业环境氟污染的措施。