Stability of a Coal Waste Artificial Reef

The feasibility of using U.K. coal-fired power station waste materials for artificial reef production is being examined. in June, 1989, an experimental artificial reef was constructed in Poole Bay, off the central south coast of the U.K., using three different mixtures of pulverised fuel ash (PFA), flue gas desulphurisation (FGD) gypsum and slurry, stabilized with cement and formed into blocks. Fifty tonnes of 40 × 20 × 20 cm blocks were formed into eight conical reef units replicating three different PFA/gypsum mixtures and one concrete control. the reef structure is 10m below chart datum on a flat sandy sea-bed.

Combustion of coal concentrates the heavy metal content in the resultant ash. the purpose of stabilization of the ash as blocks is twofold: to immobilize heavy metals (or other components) and to provide hard substratum for the attachment of organisms. to examine the effectiveness of this stabilization and hence the environmental compatibility of the block materials, heavy metal (Cd, Cr, Cu, Pb, Mn, Ni, Zn) content of the blocks has been monitored routinely over two years, to determine leaching rates. Sectional profiles indicate partial replacement of calcium content by magnesium. Associated with this there has also been some redistribution of heavy metals. Only in the case of cadmium has there been a detectable loss from the surface of blocks. Chromium and manganese concentrations appear to have increased. the metal content of the reef epibiota (including ascidians, Ascidia mentula; hydroids, Halecium spp.; bryozoans, Bugula spp. and red algae) growing on the ash blocks has been compared to that of epibiota attached to the concrete controls and surrounding sea-bed. to date no evidence of excess bioaccumulation of metals has been detected.

The physical integrity of the ash reef blocks has been maintained. There is evidence that the blocks are increasing in compressive strength.

An indication of the fishery enhancement potential of the experimental structure is given by the presence of eight commercially fished species (crustaceans and molluscs) including lobsters (Homarus gammarus).     

机动车轮胎磨损颗粒物化学组分特征研究

为研究机动车道路行驶过程中轮胎磨损排放的颗粒物理化特性,利用轮胎轮廓仿真磨耗仪,对国内主流17种轮胎胎面进行仿真磨耗实验,获得颗粒物样品,提取并检测其中18种元素和20种多环芳烃（PAHs）的含量.结果显示,元素和PAHs含量因轮胎品牌和速度等级的不同而差异显著.18种元素平均含量为（99.04±68.43）mg/g,占样品总重的9.90%,其中Si（88.97±67.85）mg/g、Zn（6.77±1.64）mg/g和Na（1.05±0.75）mg/g的平均含量均超过1mg/g,Cd的含量最低,为（0.43±0.31）μg/g.20种PAHs含量之和（∑20PAHs）在12.13~433.64 μg/g,平均为（94.13±110.18）μg/g,PY的平均含量最高（30.98±31.27）μg/g,其次是CHR、BaP、FA、PHE和BghiP,平均含量最低的是AC（0.58±0.2）μg/g;从环数看,以4环PAHs为主（占∑20PAHs的45.03%~67.93%）,其次为3环（平均含量为15.45%）和5环（平均含量为12.62%）.总体来说,国外品牌轮胎样品中元素和PAHs含量略高于国内品牌,而主要PAHs环数略低于国内品牌.     

雨水管道沉积物中典型无机氮的干期粒径分布

以南京江北新区分流制雨水管道沉积物为研究对象,考察不同粒径沉积物中铵态氮（NH₃-N）和硝态氮（NO₃^--N）干期分布特征,分析其随干期长度的变化关系,并探讨沉积物理化性质及微生物菌群结构对NH₃-N和NO₃^--N干期分布的影响.结果表明：粒径≤0.075mm的沉积物中NH₃-N占比最高（交通区30.8%,商业区36.7%）;交通区粒径≤0.075mm的沉积物中NO₃^--N占比最高（33.0%）,而商业区粒径0.075~0.15mm沉积物中NO₃^--N占比最高（34.4%）;干期长度与交通区0.075~0.15mm粒径段的沉积物中NO₃^--N含量及商业区粒径≥0.3mm的沉积物中NH₃-N含量之间的相关性均最显著;雨水管道沉积物中NH₃-N和NO₃^--N的干期分布与O-H和N-H等官能团、表面极性和亲水性、微观形貌等有一定关联;交通区雨水管道沉积物中Gemmobacter等反硝化优势菌种（相对丰度总和为20.15%）对NO₃^--N干期分布影响更显著.     

Role of glycine on sulfuric acid-ammonia clusters formation: Transporter or participator

Glycine(Gly) is ubiquitous in the atmosphere and plays a vital role in new particle formation(NPF).However,the potential mechanism of its on sulfuric acid(SA)-ammonia(A)clusters formation under various atmospheric conditions is still ambiguous.Herein,a(Gly)_x·(SA)_y·(A)_z(z≤x+y≤3) multicomponent system was investigated by using density functional theory(DFT) combined with Atmospheric Cluster Dynamics Code(ACDC) at different temperatures and precursor concentrations.The results show that Gly,with one carboxyl(-COOH) and one amine(-NH_2) group,can interact strongly with SA and A in two directions through hydrogen bonds or proton transfer.Within the relevant range of atmospheric concentrations,Gly can enhance the formation rate of SA-A-based clusters,especially at low temperature,low [SA],and median [A].The enhancement(R) of Gly on NPF can be up to 340 at T=218.15 K,[SA]=10~4,[A]=10~9,and [Gly]=10~7 molecules/cm~3.In addition,the main growth paths of clusters show that Gly molecules participate into cluster formation in the initial stage and eventually leave the cluster by evaporation in subsequent cluster growth at low [Gly],it acts as an important "transporter" to connect the smaller and larger cluster.With the increase of [Gly],it acts as a "participator" directly participating in NPF.     

加入SOA示踪的深圳大气PM2.5受体模型源解析

为厘清包括二次有机气溶胶（SOA）在内的深圳市区PM_2.5各种一次和二次来源贡献,本文于2017年9月2日~2018年8月29日在深圳市大学城点位开展PM_2.5样品采集,并进行化学组分和水溶性有机物（WSOM）质谱测量,共获得162组有效数据.观测期间深圳市大气PM_2.5平均质量浓度为26μg/m³,在传统PMF源解析的基础上加入羧基离子碎片（CO₂⁺）作为SOA的示踪物,加入水溶性有机氧（WSOO）用于计算各因子O/C,验证有机物解析效果.结果表明,SOA可以被独立解析出,其O/C明显高于其他一次污染源中有机物;机动车、二次硫酸盐、二次硝酸盐、SOA为最主要的4个源,对PM_2.5质量浓度的贡献分别为25%、23%、17%和10%,船舶、地面扬尘、老化海盐、建筑尘、生物质燃烧、燃煤和工业贡献均在5%以内.各个源的变化特征表明,机动车、二次硫酸盐、二次硝酸盐、SOA等源贡献呈现冬高夏低的季节特征,与冬季季风条件下源自内陆的污染传输密切相关.污染天气时,二次硝酸盐和SOA的贡献增加相对最显著,因此NOx和挥发性有机物是减排的关键.     

星形线电除尘器内EHD流动与粒子行为数值模拟

为了研究星形线电除尘器内电流体动力学（EHD）流动与荷电粒子运动行为及两者间相互作用,构建了线板式电除尘器（ESP）内关于EHD和带电粒子运动学的耦合数值模型.该模型采用有限体积法离散求解电场方程和空间电荷方程,在拉格朗日法下建立带电粒子运动方程,并与FLUENT湍流模型进行耦合.利用这一模型,对3种电场风速下星形线电除尘器内流动形态与粒子运动行为进行了细致模拟,并分析了二次流动对气流、粒子浓度分布的影响.结果表明,星形线电除尘通道内二次流动对流动形态和粒子浓度分布存在显著作用.随电场风速的降低,这一作用将越明显.EHD流动对细小荷电粒子运动的影响更为显著.二次流动产生涡旋并作用于主流来影响粒子运动行为.收尘板面的涡旋挤压粒子流远离壁面向流动中心运动,放电极下游的涡旋则促进粒子流向收尘板壁面靠近.此外,由于捕集通道中强二次流的存在,Deutsch计算式对除尘效率、特别是对于亚微米粒子捕集效率的计算并不准确.     

颗粒物分界层Mie散射激光雷达识别的sigmoid算法

基于成都市2013年6月~2015年5月期间由Mie散射激光雷达探测的大气消光系数廓线资料,发现混合层以上在颗粒物消光和分子消光之间一致存在一个S型的过渡区,利用sigmoid函数对此分布形态进行模拟,通过计算该函数上下曲率最大点所在的高度,据此提出了颗粒物分界层Mie散射激光雷达识别的sigmoid算法.针对该算法模拟效果的分析表明,颗粒物分界层过渡区附近大气消光系数理论廓线和实测廓线保持了高度的相关性,二者在春夏秋冬四季的相关系数（R）分别为0.9971±0.0052、0.9935±0.0167、0.9979±0.0038和0.9990±0.0021（均通过α=0.05的显著性检验）.基于sigmoid算法计算的颗粒物分界层过渡区与成都市温江站探空资料得到的逆温层之间存在很好的对应关系.     

Analysis of pollutant levels in central Hong Kong applying neural network method with particle swarm optimization

Air pollution has emerged as an imminent issue in modernsociety. Prediction of pollutant levels is an importantresearch topic in atmospheric environment today. For fulfillingsuch prediction, the use of neural network (NN), and inparticular the multi-layer perceptrons, has presented to be acost-effective technique superior to traditional statisticalmethods. But their training, usually with back-propagation (BP)algorithm or other gradient algorithms, is often with certaindrawbacks, such as: 1) very slow convergence, and 2) easilygetting stuck in a local minimum. In this paper, a newlydeveloped method, particle swarm optimization (PSO) model, isadopted to train perceptrons, to predict pollutant levels, andas a result, a PSO-based neural network approach is presented. The approach is demonstrated to be feasible and effective bypredicting some real air-quality problems.     

Trace Metal Concentration in Roadside Surface Soil and Tree Back: A Measurement of Local Atmospheric Pollution in Abuja, Nigeria

Cadmium, copper, lead, nickel and zinc concentrations were analysed by atomic absorption spectrophotometry in surface soil and tree bark from different districts of Abuja, Nigeria, in order to determine the atmospheric trace metal input in the area.Elevated concentrations of some of the studied metals were observed in the soil and tree bark samples from the commercial/high traffic areas of the city compared to backgroundvalues. In soil samples, the average concentration of the metals were 0.6±0.4, 18.0±4.0, 281±39, 16±4 and66±23 g g^-1 dry weight for Cd, Cu, Pb, Ni and Zn, respectively, whilst the average concentrations in tree bark were 0.3±0.2, 12±4, 133±32, 13±3 and 61±10 g g^-1 dry weight for Cd, Cu, Pb, Ni and Zn, respectively. The trend in trace metal levels suggested that automobile emissions are a major source of these metals as the highest concentrations of Pb and Zn were recorded in the commercial areas of the city known for their high traffic densities. The levels of metal in the study area were relativelylow compared to levels found in some larger and older cities in various countries worldwide.     

Bioindicator organisms: Heavy metal pollution evaluation in the Ionian Sea (Mediterranean Sea—Italy)

Trace metal concentrations of mercury, cadmium, lead and chromium in Patella caerulea, and Mullus barbatus were investigated to provide information on pollution of Ionian Sea, since these metals have the highest toxic potential. High chromium levels (0.47–0.97 g g^–1 ww) were registered in limpet samples collected from two station near the Gulf of Taranto, while elevated concentration of mercury (0.31–1.50 g g^–1 ww) were found in mullet specimens from Sicily. The metal concentrations recorded at the clean stations may be considered as useful background levels to which to refer for comparison within the Mediterranean area. On the contrary, the high levels of chromium and mercury found respectively in the areas near the Gulf of Taranto and at Capo Passero being of concern in terms of environmental health need frequent monitoring.