农药污染地下水的微生物治理及含水层渗透性变化研究

采用了从农药厂阿特拉津生产车间排污口污泥中分离出的菌种AT菌 ,进行了农药阿特拉津污染地下水微生物治理的模拟实验研究 ,在实验条件 (T =10℃ ,pH =7.5 )与野外含水层的条件基本一致情况下 ,难于生物降解的污染质阿特拉津的一次投菌降解率可达 3 1.0 8% ;设计了两种有效细菌的投放方式以模拟野外条件下的菌种投加条件。另外 ,AT菌的作用会造成被治理含水层的渗透性能降低 ,两种投菌方式下 ,实验后含水层的渗透系数分别下降 60 .5 4%和 3 4 5 6%。清水冲洗 10d的渗透性恢复率分别为 48.96%及 81.3 6% ,说明清水渗透恢复的方法效果明显     

荧光化学传感器的制备及其在环境分析监测中的应用

随着荧光分析技术和传感技术的发展,荧光化学传感器已经成为一种重要的连续分析测量装置.它具有很高的选择性和灵敏度,可以实现对pH、溶解氧、含氮化合物、有毒害重金属离子、有机污染物进行实时和在线测定,因此在环境分析监测方面具有广泛的应用前景.简要介绍了荧光化学传感器的原理、制备及分类,综述了近年来荧光化学传感器的发展及其在环境分析监测中的最新研究成果,并探讨了荧光化学传感器在环境分析监测领域的应用前景和发展方向.     

SBR法处理豆制品废水工艺条件的研究

用SBR法处理豆制品废水的试验表明,该系统具有较好的抗负荷冲击能力,进水COD在300～2000 mg/L之间变化,对系统不造成任何影响;考察了曝气时间、曝气量和污泥浓度等对去除效果的影响,试验结果表明,曝气时间和曝气量对处理效果影响很大,确定该反应系统最佳曝气时间是8 h,适宜的曝气量是800 L/h,而污泥浓度控制在4000 mg/L左右时,处理效率最高,采用进水顶出水的排水方式是可行的,确定系统的最佳排水比是3/5.厌氧段的插入可以减少剩余污泥的产量.     

卧式螺旋污泥好氧动态堆肥技术的研究

利用卧式螺旋式污泥好氧堆肥装置进行间歇式动态堆肥,对污水厂厌氧消化污泥进行了中温堆肥试验研究.通过控制各组堆肥的含水率、物料配比和通气量,重点探讨各种条件下堆体温度与有机物降解的关系.试验结果表明,厌氧消化污泥以木屑为调理剂在装置中可以实现好氧堆肥处理,其适宜的物料控制参数为:污泥:木屑=10:1～1.5(湿重比),堆肥含水率50%～60%;过程控制参数为:通风量为6.7～8.3 m3/h·t,发酵周期为8 d,温度45℃.     

常熟河网区水污染物总量控制研究

基于常熟河网原型调水实验和水功能区划，建立了感潮地区河网水量水质模型，对常熟河道水质降解系数及水环境容量进行了计算，并按照点源和面源对区域内污染源进行统计，在此基础上进行了常熟河网水污染物总量控制值和现状削减量的计算，为该地区的水污染防控提供了科学依据。     

膨胀珍珠岩负载TiO2光催化脱色性能的研究

以钛酸四丁酯为原料 ,膨胀珍珠岩为载体 ,用溶胶 -凝胶法制备可漂浮于水面的负载型TiO2 。利用该负载型TiO2 对罗丹明B(RB)进行光催化脱色实验 ,结果表明 ,浸渍 3次的负载型TiO2 光催化活性最高 ,催化剂最佳用量为 5 0 0mg/10 0mLRB ,经 5h光照 ,对 10 0mL浓度为 1mg/L和 2 .5mg/LRB脱色率分别为 76 .6 7%和 4 7.2 7% ;该催化剂使用寿命长 ,2 5h后催化剂脱色性能没有减弱 ,可重复使用 ;经 8h光照 ,染料废水脱色效果好。     

各种影响因子对电解法预处理医药废水的影响研究

探讨了电解法预处理医药废水时停留时间、电解电压、废水初始浓度、温度和废水pH值等影响因子对去除色度、COD和提高废水可生化性等处理效果的影响，并考察了其应用于工业实际废水处理的可行性。实验结果表明：电解法更适合高浓度医药废水的处理，色度的去除率可达到90％以上；电解时间宜控制在40-60min；电解电压越高，废水COD和色度去除效果越好；在实验温度范围内，温度对色度和COD去除率的影响不大；废水pH值为7．5时电解效果最佳，工程运用宜控制在6—9之间。     

高效喷淋泡沫脱硫技术及装置的应用

SO2是产生酸雨的主要气体，其主要来源于工业燃煤锅炉。以沈阳一家电厂为例，该厂选用新型高效的喷淋泡沫脱硫除尘器对锅炉排放的SO2进行治理。进入喷淋泡沫塔前的SO2平均浓度为2780mg／m^3，经脱硫后出塔平均浓度为289．3mg／m^3，去除率为89．6％。结果表明，这种有别于传统湿法的新型高效的喷淋泡沫脱硫技术及装置具有脱硫效率高、装置占地少、运行稳定、沉淀物易于回收利用等特点，对锅炉排放的SO2进行治理是非常有效的。     

Can aquatic distribution of human pharmaceuticals be related to pharmacological data?

The recognition of pharmaceuticals as significant environmental contaminants has only been a recent phenomenon. Therefore there is a paucity of data relating to the fate and effects of pharmaceuticals once they enter an aquatic receiving system. The amount of work that needs to be done in terms of risk assessment for pharmaceuticals required by regulatory agencies is substantial. This paper has determined the environmental partitioning coefficient (K_d) of 13 diverse human pharmaceuticals in three model systems of differing combinations of solid phases and solutions. The K_d values were then compared with distribution values of the pharmaceuticals in the human body determined from pharmacological studies. This was done to assess the functional relationship between K_d and distribution values in the human body (V_D). K_d values ranged from 3 to 2450 L kg⁻¹. Regression coefficients ranged from r² = 0.62–0.72, indicating that V_D values are a useful indicator for the K_d values of the tested pharmaceuticals within the batch sorption systems. The relationship between K_d and V_D should therefore be further explored to determine whether this relationship can be applied to a broader range of pharmaceuticals in more diverse environmental systems. Exploiting available human pharmacological data in such a way would be of great benefit in prioritising human pharmaceuticals as environmental contaminants in the risk assessment process.     

Investigation of the complexation of metal-ions by strong ligands in fresh and marine water

SCOPE: The detection and investigation of metal ions bound in strong complexes in natural waters is a difficult task, due to low concentration of the metal ions themselves, and also of the strong ligands, which, moreover, are often not of a well-defined composition. Here, a method is proposed for the investigation of the speciation of metal ions in natural waters. OBJECTIVE AND METHOD: It is based on the sorption of metal ions on strongly sorbing ion exchange resins, i.e. complexing resins. For this reason the method is called Resin Titration. It has been shown in previous investigations that the concentration of metal ion totally sorbed by a particular resin, and its reaction coefficient in the solution phase in the presence of the resin, can be determined from the sorption data using a simple relationship. Here, a data treatment (the Ruzic linearization method) is proposed for also determining the concentration of the ligands responsible for the complex in equilibrium with the resin. RESULTS: The method was applied to data obtained by Resin Titration of a freshwater and a seawater. Copper(II) and aluminium(III) were considered, using Chelex 100 as a titrant, due to its strong sorbing properties towards these metal ions. The results were: the total metal concentration in equilibrium with the resin, the side reaction coefficients, and the concentration of ligands. In all these cases the ligands forming very strong complexes were found to be at concentration lower than that of the metals. CONCLUSION: The Ruzic linearization method allows the determination of the concentration of the ligands forming very strong complexes in equilibrium with Chelex 100. The reaction coefficient was better determined by the calculation method previously proposed for RT. The ligands responsible for the strong complexes were found to be at low concentration, often lower than that of the metal ions considered. The metal in the original sample is partly bound to these ligands, since the complexes are very strong. Only a part of the metal is linked to weaker ligands, or free.