HZ-16型大孔树脂吸附处理含RDT-8废水

采用HZ-16型大孔树脂对含三（三溴苯氧基）三嗪（RDT-8）废水进行吸附及脱附处理。实验结果表明：在废水流量为4.0 BV/h的条件下,树脂最佳吸附工艺条件为出水体积88.0 BV,此条件下出水COD小于291 mg/L,挥发酚质量浓度小于0.08 mg/L;在脱附液流量为0.5 BV/h的条件下,树脂最佳脱附工艺条件为脱附液体积3.0 BV,此条件下脱附液中挥发酚质量浓度为30.6 mg/L,挥发酚脱附率高达76.4%。在最佳吸附-脱附工艺条件下,连续进行10次动态吸附-脱附实验,吸附出水中COD为137~294 mg/L,COD去除率为72.5%~89.1%,挥发酚质量浓度稳定在0.05 mg/L以下,挥发酚去除率为99.8%~100%,说明HZ-16型大孔树脂的吸附-脱附性能稳定。     

Atmospheric bulk deposition of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in the vicinity of an iron and steel making plant

An IRA-743 resin bulk sampler was validated to monitor long-term bulk deposition of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). Six consecutive sampling campaigns (2008-2009) were conducted at four sites around steel complexes in Pohang, South Korea to investigate spatial and seasonal variations of PCDD/F bulk deposition. The bulk deposition within the steel complex showed the highest ∑_4-8PCDD/F (Tetra-Octa) fluxes, ranging from 204 to 608 (mean: 352) pg m⁻² d⁻¹, indicating steel complexes were major sources of PCDD/Fs. The homologue profiles were dominated with lower chlorinated PCDFs. Furthermore, the prevailing winds were confirmed to influence the spatial distribution of PCDD/F deposition. There were apparent seasonal variations of the bulk deposition at each site, and seasonal homologue patterns of PCDD/Fs were clearly observed. According to the passive air sampling, however, no significant seasonal change of ambient air concentrations of PCDD/Fs was observed. Therefore, it was concluded that the seasonal variations of deposition fluxes of PCDD/Fs probably resulted from temperature-dependent gas/particle partitioning.     

混凝-生物强化联合处理环氧树脂高盐废水

环氧树脂高盐废水是目前较难处理的工业废水之一.采用混凝联合生物强化工艺:通过混凝过程进行预处理后,投加嗜盐菌进行生物强化考察盐度变化对系统降解有机物的影响以及污泥性状的变化情况.结果表明,当废水中氯离子浓度达到驯化目标10 g/L时,系统对COD的去除率仍稳定在85％左右;以没有投加嗜盐菌的反应器为对照组,在进水COD平均浓度为550 mg/L左右,氯离子浓度由12 g/L增至21 g/L时,对照组COD平均去除率由82％降至60％以下,而投加了嗜盐菌的反应器(投加组)则仍保持在85％以上;此外,盐度的变化同时影响污泥的活性及其沉降性能,随着盐度增大,两组中的污泥活性均有所降低,但投加组的污泥活性相对较高,其污泥的沉降时间和污泥体积指数(sludge volume in-dex,SVI)值也较低.采用本工艺处理环氧树脂高盐废水,使得生物处理过程能够长期稳定运行,且能够保持较高的耐盐度和COD去除率.     

改性树脂NKZ对水溶性染料的吸附特性研究

根据聚合物絮凝剂与染料相互作用机理,用硝基胍对大孔型氯球改性得到了功能化吸附树脂NKZ.从热力学和动力学两方面研究了该树脂对5种水溶性染料的静态吸附特性.结果表明,树脂NKZ对水溶性染料的吸附具有很好的效果.     

磷酸银/树脂复合物的制备及其对亚甲基蓝的光催化降解

以聚乙烯吡咯烷酮(PVP)为稳定剂,采用化学沉积法制备了磷酸银/树脂复合物,降解亚甲基蓝,研究其光催化活性,并对样品进行了XRD和SEM表征。探讨了不同的光源、催化剂投加量、PVP含量、p H值等因素对亚甲基蓝降解率的影响。结果表明,在太阳光(夏天早上9点到11点的阳光)下,偏酸介质中,催化剂用量为0.8 g/L,PVP质量分数为0.01%的磷酸银/树脂复合物,液面高度为15 cm的条件下对亚甲基蓝有最佳降解效果。     

微波在废树脂中的穿透厚度研究

通过对不同功率微波在不同规格钢桶中对不同含水率的树脂中的穿透厚度的研究可知,微波在树脂中的穿透厚度主要与树脂自身含水率有关,与钢桶的规格尺寸也有一定的关系,而微波功率的影响则可基本忽略不计;对于含水率50％左右的树脂,微波在12L钢桶中的穿透厚度是130 mm;在200L钢桶中的穿透厚度是70mm.该研究成果对微波干燥工艺的具体参数的选取和扩大规模台架装置的设计研究等有重要意义.     

固定化多酚氧化酶对水中苯酚和氯酚的去除

以壳聚糖/蒙脱土插层复合物为载体,吸附法制备固定化多酚氧化酶,并以此催化氧化去除水中的苯酚、4-氯苯酚和2,4-二氯苯酚.考察了固定化多酚氧化酶的制备条件,对酚类化合物的催化氧化条件、动力学特性以及固定化酶的重复使用性能.结果表明,固定化多酚氧化酶的最佳制备条件为p H 5.0,酶与载体质量比20 mg·g-1,固定化6 h,所得固定化酶的载酶量为12.12 mg·g-1,每克单位载体酶活为12.76×103U·g-1.固定化多酚氧化酶对酚类化合物的最佳去除条件为:苯酚溶液p H 7.0,温度30℃;4-氯苯酚溶液p H 5.0,温度20℃;2,4-二氯苯酚溶液p H 5.0,温度30℃.在最佳反应条件下,酶与底物质量比为20 mg·mg-1时,固定化多酚氧化酶对苯酚、4-氯苯酚和2,4-二氯苯酚溶液去除率分别为63.6%、85.8%和87.8%.苯酚、4-氯苯酚和2,4-二氯苯酚的米氏常数Km值依次减小,最大反应速率Vmax依次增大,表明固定化酶对2,4-二氯苯酚的亲和力最强,催化速度最快.固定化酶循环使用6次(24 h)后对苯酚、4-氯苯酚和2,4-二氯苯酚的去除率分别为15.7%、24.2%和27.8%.     

印染废水RO浓水水质分析

以江苏某印染废水处理厂反渗透（RO）浓水为研究对象,采用多种分析手段分析了RO浓水的水质特征.首先采用IC和ICP-MS对水中的无机离子进行了定性和定量分析,采用GC-MS对废水中的半挥发性有机物进行定性和定量分析.结果表明,RO浓水中无机离子以Na⁺、Cl^-和SO₄^2-为主,半挥发性有机物邻苯二甲酸二（2-乙基己）酯（DEHP）为主要成分,其浓度为1.452mg/L.为分析RO浓水中的溶解性有机物（DOM）特征,进一步采用超滤膜分子量分级法和树脂亲疏水分离技术对废水中的DOM进行分离解析,分析了不同组分的溶解性有机碳（DOC）、UV₂₅₄、SUVA含量和分布情况,应用三维荧光光谱对各组分物质进行了定性分析.超滤分级表明,RO浓水中相对分子量<1k的有机物占56.98%,相对分子质量5~10k有机物仅占2.19%,但其芳香化程度较高.树脂分离结果表明,RO浓水中亲水性物质（HPI^*）、疏水性物质（HPO^*）和过渡性物质（TPI^*）的DOC含量差异不大,其中HPO^*的芳香构造化程度最高,含有较多的色氨酸类芳香族蛋白质,而HPI^*中含有较多的溶解性微生物代谢产物类物质.     

C/C复合材料不同碳基体的纳米压痕行为研究

目的研究碳基体微观结构对材料整体性能的影响。方法用酚醛浸渍-碳化、中温煤沥青浸渍-碳化、甲烷为碳源前驱体,经化学气相沉积制备得到不同碳基体C/C复合材料。采用偏光显微镜对C/C复合材料不同碳基体的显微结构进行观察分析,采用XRD和Raman光谱对C/C复合材料的树脂碳基体、沥青碳基体和热解碳基体的微晶尺寸进行表征,以玻璃碳作为参比样品,通过纳米压痕测试不同碳基体试样的弹性模量和硬度。结果碳基体为热解碳和沥青碳的石墨微晶缺陷少,完整度较好,石墨化程度高。玻璃碳和树脂碳基体中石墨微晶排列紊乱,有序度低,石墨化程度低。酚醛浸渍-碳化得到的树脂碳的微晶尺寸Lc最小,为1.69 nm,弹性模量和硬度最大,分别为(23.17±0.54) GPa和(3.26±0.10) GPa;光滑层热解碳和粗糙层热解碳的弹性模量和硬度次之;沥青碳的微晶尺寸最大,Lc为9.36nm,而弹性模量和硬度最小,分别为(12.53±2.29) GPa和(0.72±0.14) GPa。结论不同碳基体的C/C复合材料中,碳基体的石墨化度越高,微晶尺寸越大,各向异性越显著,材料的弹性模量和硬度越低。     

Novel Biocomposites Sheet Molding Compounds for Low Cost Housing Panel Applications

Biocomposites were made by a novel high volume processing technique named biocomposite sheet molding compound panel (BCSMCP) manufacturing process. This process design was inspired by the commercial glass fiber–polyester resin composite fabrication method called sheet molding compounding (SMC). This process yields continuous production of biocomposites on a large scale, and thus can be easily adopted in industries. A unique fiber dispersion method, which enabled uniform distribution of natural fibers, was used in this process. Consistency of the process was tested by evaluating the repeatability of the resultant materials mechanical properties. The low cost biocomposites produced as a result of the processing will be used for various panel applications such as housing and transportation. The molded samples were tested for various mechanical and thermal properties, in accordance with ASTM procedures. The biocomposites were made with various natural fibers including, big blue stem grass, jute, and industrial hemp. By combining different natural fibers in varying mass fractions, hybrid biocomposites were made using this process. Grass fiber reinforced polyester biocomposites processed by the SMC line showed very promising results.