城市污水生物脱氮除磷的新理论与技术

评述了近年来城市污水生物脱氮除磷理论和功能微生物的研究进展,重点介绍了生物处理的新方法：短程硝化反硝化处理法、厌氧氨氧化处理法、同步硝化反硝化处理法、同步反硝化除磷脱氮法,并总结了各处理工艺的应用状况。对生物脱氮除磷微生物学和新的理论技术发展趋势做出了展望。     

生物过滤塔净化甲醛废气的动力学研究

选用榛子壳作为反应器的填料,利用沈阳北部污水处理厂的活性污泥对填料进行挂膜,由低到高通入甲醛气体进行驯化。在系统稳定后进行了生物过滤塔净化甲醛气体的实验研究,并建立了生物过滤塔降解甲醛气体的动力学模型。结果表明,入口气体浓度在低于25mg/m3时,甲醛废气的净化效率可保持在97％以上,超过此浓度值时,效率明显下降。随着进口气体流量的增加,净化率逐渐下降,由入口流量为0．2m3／h时的97．25％下降到入口流量为0．8m弧时的57．2％。根据现有动力学模型及本实验得出数据所建立的生物过滤塔净化甲醛气体的动力学模型,可以较好地模拟系统处理甲醛废气的实验结果,验证了模型的正确性。     

中俄联合监测水质中总磷测定实验的方法与结果对比分析

近年来,中俄双方开展了对等联合监测,但由于国域差别,两个国家在一个项目上采取了不同的实验方法,常出现同一个样品中俄双方出现不同的实验结果,为避免分歧,我国在少数几个站进行了中俄双方实验方法的对比实验,现就水质中总磷的测定将两国的实验方法和实验结果进行了分析。     

微压流化式复合生物反应器处理含酚废水效能的研究

通过连续动态试验,对新型微压流化式复合生物反应器(MP-FHBR)处理模拟苯酚废水的效能进行研究.结果表明,MP-FHBR的COD容积负荷可达4.86kg/(m3·d)、苯酚容积负荷可达1.96kg/(m3·d),出水COD低于200mg/L、出水苯酚浓度低于1mg/L,COD和苯酚去除率分别达到90%和99%以上.当苯酚容积负荷达到2.04kg/(m3·d),苯酚在反应器中逐渐累积,反应器内微生物的TTC-比脱氢酶活性下降.当MP-FHBR进水苯酚浓度为800mg/L时,最佳水力停留时间为9～10h.水力负荷对反应器沉淀池的泥水分离效果影响较大,限制了反应器的进水量,所以MP-FHBR主要适用于处理较高浓度的含酚废水.     

企业风险管理与经营效率：来自中国保险业的经验证据

本文从风险管理的视角对企业效率评估的数据包络分析技术进行了改进,探讨了风险管理与经营效率的内在关联,并以中国保险业为例,对1999年以来企业真实的经营效率水平进行了评估。结果表明：企业内部的风险管理能力对其经营效率水平的提升具有明显的影响,而且这种影响力正在逐渐加强。不考虑企业内部的风险管理水平将直接导致其经营效率的测算结果出现低估,2002年以后这种低估的程度越发明显,这可归因于同期保险企业开始逐渐重视提高自身的风险管理能力。以上结论也为企业如何在管控风险的同时提升经营效率水平提供了有价值的指导。     

有关斜管沉淀池的上升流速讨论

文章从理论上了分析斜管沉淀池上升流速对沉淀池处理效果的影响,及原水特性与斜管沉淀池上升流速取值的关系。讨论分析斜管沉淀池设计时,应根据原水特性不同选择不同的斜管沉淀池上升流速。     

不同喷雾方式下低阻文丘里振弦栅除尘配置优化实验研究

为了对比径向外喷和轴向喷雾下的低阻文丘里振弦栅耦合除尘效果,以除尘效率和系统阻力为参照,选定喉管气速、振弦栅数、纤维丝间隙和喉管液气比进行单因素实验。结果表明2种喷雾方式的除尘效率和系统阻力的变化趋势相同。利用SPSS软件进行4因素3水平正交实验设计,在特定参数条件下,2种喷雾方式的因素影响排序相同,除尘效率为纤维栅数＞纤维丝间隙＞喉管气速＞喷雾量;系统阻力为喉管气速＞纤维栅数＞纤维丝间隙＞喷雾量;径向外喷最佳配置为喉管气速24 m/s、喷雾量2.3 L/min、2块间隙为0.8 mm纤维栅板;轴向喷雾为喉管气速28 m/s、喷雾量2.4 L/min、2块间隙为0.8 mm纤维栅板;在最优配置下的除尘性能为径向外喷＞轴向喷雾。     

Utilization of MSWI fly ash as partial cement or sand substitute with focus on cementing efficiency and health risk assessment

• Washed MSWI fly ash was used as partial cement or sand substitute. • Sand replacing is beneficial for strength, while cement replacement reduces strength. • Cementing efficiency factor and mortar pore structure explain the strength results. • Health risk assessment was conducted for MSWI fly ash blended cement mortar. • CR and HI contributed by different exposures and heavy metals were analyzed. The strength of cement substituted mortar decreases with the increase in fly ash amount, whereas the strength increases when the fly ash is blended as sand substitute. A mortar with highest strength (compressive strength= 30.2 Mpa; flexural strength= 7.0 Mpa) was obtained when the sand replacement ratio was 0.75%. The k value (cementing efficiency) of fly ash varied between 0.36 and 0.15 for the fly ash fraction in binder between 5% and 25%. The k values of fly ash used for sand replacement were all significantly above that used for cement substitution. The macropores assigned to the gaps between particles decreased when the fly ash was used as sand replacement, providing an explanation for the strength enhancement. The waste-extraction procedure (toxicity-sulphuric acid and nitric acid method (HJ/T 299-2007)) was used to evaluate metal leaching, indicating the reuse possibility of fly ash blended mortar. For the mortar with the mass ratio of fly ash to binder of 0.5%, the carcinogenic risks (CR) and non-carcinogenic hazard quotient (HQ) in sensitive scenario for blended mortar utilization were 9.66 × 10^-7 and 0.06, respectively; these results were both lower than the threshold values, showing an acceptable health risk. The CR (9.89 × 10^-5) and HQ (3.89) of the non-sensitive scenario for fly ash treatment exceeded the acceptable threshold values, indicating health risks to onsite workers. The main contributor to the carcinogenic and non-carcinogenic risk is Cr and Cd, respectively. The CR and HQ from inhalation was the main route of heavy metal exposure.     

Modelling Phosphorus Retention in Lakes and Reservoirs

Steady-state models for the prediction of P retention coefficient (R) in lakes were evaluated using data from 93 natural lakes and 119 reservoirs situated in the temperate zone. Most of the already existing models predicted R relatively successfully in lakes while it was seriously under-estimated in reservoirs. A statistical analysis indicated the main causes of differences in R between lakes and reservoirs: (a) distinct relationships between P sedimentation coefficient, depth, and water residence time; (b) existence of significant inflow–outflow P concentration gradients in reservoirs. Two new models of different complexity were developed for estimating R in reservoirs: , where τ is water residence time (year), was derived from the Vollenweider/Larsen and Mercier model by adding a calibrated parameter accounting for spatial P non-homogeneity in the water body, and is applicable for reservoirs but not lakes, and , where [P_in] is volume-weighted P concentration in all inputs to the water body (μg l⁻¹), was obtained by re-calibrating the OECD general equation, and is generally applicable for both lakes and reservoirs. These optimised models yield unbiased estimates over a large range of reservoir types.     

改良倒置A2/O工艺设计

在目前广泛采用的AO、A2O、倒置A2O等工艺的基础上,为提高脱氮除磷效率,提出改良倒置A2O工艺。并对其工艺的特点、设计和脱氮除磷效率进行了详细的研究和分析。