邻苯二甲酸和苯甲酸在功能化碳纳米管上的吸附行为

在pH7.0的条件下,采用批量平衡方法研究邻苯二甲酸（PA）和苯甲酸（BA）在3种不同功能化碳纳米管（羟基化H-CNTs、羧基化C-CNTs和石墨化G-CNTs）上的吸附/解吸行为,并进一步探究共存BA对PA在碳纳米管上吸附的影响.结果表明,Langmuir和Freundlich模型均可对PA和BA在3种碳纳米管上的吸附数据进行较好的非线性拟合,其中Freundlich模型拟合效果更好（Adj r²均达到0.88以上）;3种碳纳米管对PA和BA的吸附能力大小均依次为：C-CNTs > H-CNTs > G-CNTs;解吸实验中,C-CNT和H-CNTs对BA和PA的解吸均具有明显的滞后现象,说明BA和PA在C-CNT和H-CNTs上的吸附有较强化学作用力的发生,而G-CNTs对二者的解吸曲线与吸附曲线几乎重合,不具有明显的滞后现象,这与G-CNTs表面缺乏官能团有关;当PA和BA共存在时,以PA为主要吸附质,BA为竞争吸附质,发现在H-CNTs和C-CNTs上,共存BA对PA为竞争作用,而在G-CNTs上,共存BA对PA起协同吸附作用.     

模拟三峡库区消落带土壤有机磷酸酯淹水释放特征

本研究以三峡库区消落带典型土壤作为研究对象,通过室内模拟实验,探讨了有机磷酸酯(OPEs)的含量、环境温度、土壤有机质含量、微生物因素的变化对土壤中常见OPEs单体迁移释放的影响.结果表明,土壤中OPEs含量越低,其迁移释放量越低;有机质含量升高,土壤向上覆水释放的OPEs减少,预示土壤添加有机质后对OPEs的释放产生了一定的抑制作用,有机质对OPEs的吸附起主要作用,但当有机质含量(以干重计)高于30 g·kg~(-1)时,对OPEs释放的抑制作用并未显著增强;在环境温度为27℃时,三类OPEs的平均释放量为1 077. 3 ng·m L~(-1),高于7℃的释放量,说明高温对OPEs的释放起促进作用.微生物对其作用并不明显.氯类的OPEs包括磷酸三(2-氯乙基)酯(TCEP)、磷酸三(1-氯-2-丙基)酯(TCPP)和磷酸三(1,3-二氯异丙基)酯(TDCP)为最主要的释放单体,主要原因可能是氯类OPEs的辛醇水分配系数(Kow值)和有机碳分配系数(Koc值)比烷烃类和芳烃类OPEs低,更易溶于水体,不易被土壤中的有机质吸附,因此氯类OPEs更易从土壤中迁移释放到上覆水中,成为三峡库区上覆水中主要的OPEs单体.     

UV/TiO2薄膜体系光降解酞酸酯研究

采用自制玻璃负载TiO2薄膜,研究了UV-V is/TiO2以及UV/TiO2/H2O2体系对2种酞酸酯DBP和DEHP的光催化降解情况。研究结果表明,TiO2在暗处对酞酸酯没有降解作用;UV/TiO2体系能有效光降解DBP和DEHP,TiO2具有明显的光催化作用,增强因子分别为fDBP=2.06,fDEHP=1.53;在一定浓度范围内DBP在UV/TiO2体系中的降解速率与其初始浓度成负一级动力学关系;UV/TiO2/H2O2体系对DBP的光降解能力远大于UV/TiO2和UV/H2O2体系,H2O2能显著提高TiO2的光催化活性。     

Sorption and desorption kinetics of phthalates and phenol on water/sediment interface

Ｓｏｒｐｔｉｏｎａｎｄｄｅｓｏｒｐｔｉｏｎｋｉｎｅｔｉｃｓｏｆｐｈｔｈａｌａｔｅｓａｎｄｐｈｅｎｏｌｏｎｗａｔｅｒ／ｓｅｄｉｍｅｎｔｉｎｔｅｒｆａｃｅＹｅＣｈａｎｇｍｉｎｇ，ＺｈａｏＷｕｓｈａｎ，ＬｉＴｉｅ，ＬｅｉＺｈｉｆａｎｇ，ＹａｎＨａｉＲｅｓ...     

Biodegradability of blends of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) with cellulose acetate esters in activated sludge

Blends of the bacterially produced polyester poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) with cellulose acetate esters (CAE) further substituted with propionyl or butyryl groups (degree of substitution: 2.60 propionyl and 0.36 acetyl or 2.59 butyryl and 0.36 acetyl, respectively) were exposed for 4 months to activated sludge to determine their biodegradability. Samples of such blends made by solution-mixing and solvent-casting had complex morphologies in which both individual components as well as a miscible blend phase were present. Additionally, the two opposite surfaces of solvent-cast films showed both physical and chemical differences. After 2 months, samples of pure PHBV had degraded by more than 98% (15 mg/cm² of surface area), whereas a pure CAE sample had degraded less than 1% (<0.2 mg/cm²). Samples containing 25% CAE lost less than 40% of their initial weights (6 mg/cm²) over the total 4-month period. Samples with 50% CAE lost up to 16% weight (2 mg/cm²), whereas those containing 75% CAE lost only slightly more weight than corresponding sterile control samples (1 mg/cm²). NMR results confirm that weight loss from samples containing 25% CAE resulted only from degradation of PHBV and that the surface of samples became enriched in CAE. Solvent-cast film samples containing equal amounts of PHBV and CAE degraded preferentially on the surface which formed at the polymer-air interface. Scanning electron microscopy and attenuated total reflectance infrared spectroscopy revealed this surface to have a rougher texture and a greater PHBV content.     

银川城区地表灰尘中邻苯二甲酸酯污染特征及人群健康风险评价

采集银川市城区不同功能区的40个地表灰尘样品,采用气相色谱质谱联用的检测方法,测定了美国环保局（EPA）优先控制的6种PAEs化合物的含量,并对其污染特征、污染分布和人体暴露的健康风险进行了评价.结果表明,6种邻苯二甲酸酯化合物在地表灰尘样品中均被检测出,Σ₆PAEs的含量为0.096~24.952 mg·kg^-1,平均值和中位数分别为3.452 mg·kg^-1和1.905 mg·kg^-1.各功能区地表灰尘中Σ₆PAEs平均含量由高到低依次为住宅区、文教区、公园、工业区、商业区和交通区.各功能区地表灰尘中的主要PAEs单体为邻苯二甲酸（2-乙基）己酯（DEHP）和邻苯二甲酸二丁酯（DnBP）,二者占到Σ₆PAEs的97.07%.对人体健康风险评价表明,研究区6种优先控制化合物对人体产生的非致癌风险均小于1,未超过EPA推荐的非致癌水平,邻苯二甲酸丁基苄基酯（BBP）的致癌风险在可接受的标准范围内,有2个样点的DEHP致癌风险超过EPA推荐的致癌水平,应引起一定的重视.     

A2O小试系统与实际工艺单元中OPEs去除的比较

污水处理厂出水是环境中OPEs的重要来源,且污水处理厂的生物处理单元可去除部分OPEs.为了更好的研究污水处理厂工况条件,以达到优化去除宏量有机物和微量有机物的目的,良好的小试装置必不可少.本研究在实验室设计并安装了一套A²O小试装置,根据有机磷酸酯的结构特点,在进水中投加了3种代表性的有机磷酸酯.比较了小试装置中与实际工艺单元中这3种有机磷酸酯的去除规律,发现OPEs在A²O小试中的去除规律与实际工艺单元中相似,磷酸三丁氧酯（TBEP）在两种工况下去除效果均较好,总去除率分别为84.6%与83.6%,磷酸三（1-氯-2-丙基）酯（TCPP）去除效果均较差.在不同处理单元中,由于厌氧池中主要发生水解作用,TCPP在两种工况下的厌氧池中都可去除,且在A²O小试厌氧池中的去除率（57.7%）优于实际工艺（25.5%）.TBEP的去除主要发生在好氧池中,且A²O小试二沉池可以有效去除TBEP（67.9%）,优于实际工艺的二沉池.两种工况下,好氧池曝气强度较大,引入磷酸三（1-氯-2-丙基）酯（TCPP）不易降解,TCPP在好氧池去除效果较差.除此之外,优化了小试装置的OPEs的检测取样量保证检测的准确性.     

黄河中下游水体中邻苯二甲酸酯的分布特征

采集了黄河中下游12个断面的河水、沉积物和悬浮颗粒物样品,用气相色谱法对样品中邻苯二甲酸酯类(PAEs)有机物含量进行测定,分析其在黄河水体中的分布特征.结果表明,在小浪底-东明桥之间,干流水相PAEs浓度分布范围为3.99×10^-3～45.45×10^-3mg/L;支流浓度范围为15.80×10-3～49.53×10^-3mg/L,远远高于干流的浓度.在所研究支流中,洛阳石化污水沉积相中的PAEs含量最高,达到331.70mg/kg;PAEs在干流各断面沉积相中的浓度变化范围为30.52～85.16mg/kg;沿程变化主要受支流的汇入和各处沉积物理化性质的影响.在干流焦巩桥至东明桥区间,悬浮颗粒相的PAEs总量水平沿程呈上升趋势,浓度由40.56mg/kg增至94.22mg/kg.邻苯二甲酸双(2-乙基己基)酯(DEHP)和邻苯二甲酸二丁酯(DBP)所占比例相对较大.干流与支流水相中的DEHP,除孟津和焦巩大桥处未超标,其余各处均已超标.     

Performance studies of a low heat rejection engine operated on non-volatile vegetable oils with exhaust gas recirculation

During recent decades, considerable effort has been expended world-wide to reduce dependency on petroleum fuels for power generation and transportation through the search for suitable alternative fuels that are environmentally friendly. In this respect, vegetable oils are a promising alternative to diesel fuel. However, the high viscosity, poor volatility and cold flow characteristics of vegetable oils can cause some problems such as injector coking, severe engine deposits, filter gumming and piston ring sticking and thickening of lubrication from long-term use in diesel engines. These problems can be eliminated or minimised by transesterification of the vegetable oils to form monoesters. Although transesterification improves the fuel properties of vegetable oil, the viscosity and volatility of biodiesel are still worse than those of petroleum diesel fuel. The performance of a diesel engine with such biodiesel operation can be improved further with the concept of the low heat rejection (LHR) engine. In the LHR engine, combustion surfaces on the pistons, cylinder walls and valves can be coated with ceramic materials. The objective of this study was to apply the LHR engine concept for improving engine performance when either honge biodiesel, known as honge oil methyl ester (HOME), or neem biodiesel, known as neem oil methyl ester (NOME) oils was used as an alternative fuel. For this purpose, experiments were conducted on a single cylinder, four-stroke, direct injection, water-cooled compression ignition engine using diesel, HOME and NOME oils at different injection timings of 19, 23 and 27° before top dead centre (BTDC) with and without the induction of exhaust gas recirculation (EGR). The percentage of EGR was varied from 5 to 20% in steps of 5%. The results showed that specific fuel consumption and brake thermal efficiency were improved for both of the biodiesel fuels in the LHR engine. An EGR of 10% resulted in better performance with trade-off between oxides of nitrogen and hydrocarbons/carbon monoxide emissions and hence 10% EGR is taken as the best of the range from 5 to 20%. However, readings with other EGR ratios are not reported.     

Combustion characteristics of a four-stroke CI engine operated on Honge and Jatropha oil methyl ester–ethanol blends when directly injected and dual fuelled with CNG induction

The demand for petroleum products in India has been increasing at a rate higher than the increase of domestic availability. At the same time, there is continuous pressure on emission control through periodically tightened regulations particularly in metropolitan cities. In the wake of this situation, there is an urgent need to promote the use of alternative fuels as substitutes for high-speed diesel. Dual-fuel mode of operation employing compressed natural gas (CNG) and plant oils such as Honge and Jatropha oils and their esters is an attractive option as our country has a large agriculture base that can be a feedstock to this fuel technology which can ease the burden on the economy by curtailing fuel imports. This paper presents the results of investigations carried out in studying the behaviour of Honge and Jatropha oil methyl esters and their blends with 15% ethanol and subsequent testing of these oils in a four-stroke, single-cylinder, water-cooled, direct-injection compression ignition engine in dual-fuel mode with CNG induction.