Multi-response optimization of Fenton process for applicability assessment in landfill leachate treatment

Fenton process, as a pretreatment method, was found to be effective in the primary treatment of mature/medium landfill leachate. However, the main problem of the process is the large amount of produced sludge that requires an accurate feasibility evaluation for operational applications. In this study, the response surface methodology was applied for the modeling and optimization of Fenton process in three target responses, (1) overall COD removal, (2) sludge to iron ratio (SIR) and (3) organics removal to sludge ratio (ORSR), where the latter two were new self-defined responses for prediction of sludge generation and applicability assessment of the process, respectively. The effective variables included the initial pH, [H₂O₂]/[Fe²⁺] ratio and Fe²⁺ dosage. According to the statistical analysis, all the proposed models were adequate (with adjusted R² of 0.9116–0.9512) and had considerable predictive capability (with prediction R² up to 0.9092 and appropriate adequate precision). It was found that all the variables had significant effects on the responses, specifically by their observed role in dominant oxidation mechanism. The optimum operational conditions obtained by overlay plot, were found to be initial pH of 5.7, [H₂O₂]/[Fe²⁺] ratio of 17.72 and [Fe²⁺] of 195 mM, which led to 69% COD removal, 2.4 (l sludge/consumed mole Fe²⁺) of SIR and 16.5 (gCOD removed/l produced sludge) for ORSR in verification test, in accordance with models-predicted values. Finally, it was observed that [H₂O₂]/[Fe²⁺] ratio and Fe²⁺ dosage had significant influence on COD removal, while Fe²⁺ dosage and [H₂O₂]/[Fe²⁺] ratio had remarkable effects on SIR and ORSR responses, respectively.     

两级氧化法处理油田压裂返排液

采用两级氧化法处理油田压裂返排液。在次氯酸钠、次氯酸钙、过氧化氢、高锰酸钾4种氧化剂中,次氯酸钠的氧化效果最好。以次氯酸钠作为一级氧化剂,进行一级氧化处理;再分别采用次氯酸钙、过氧化氢、高锰酸钾进行二级氧化处理。在次氯酸钠加入量为40mL/L、一级氧化反应时间为30min、二级氧化反应时间为30min、初始废水COD为3976mg/L的条件下,二级氧化剂过氧化氢、次氯酸钙、高锰酸钾的最佳加入量分别为80,40,40mL/L,对应的COD去除率分别为82.60%,71.50%,83.50%。     

巯基硅烷改性氧化石墨对砷的吸附性能

为提高氧化石墨(GO)对砷的吸附能力,以3-巯基丙基三甲氧基硅烷为改性剂,制备了巯基改性的氧化石墨(GO-SH),考察其对水中砷的吸附性能.采用单因素实验法考察了初始pH值、吸附剂投加量、温度等对吸附效果的影响,拟合了吸附等温线,并研究了吸附动力学和吸附热力学规律.实验结果表明,在最优条件下,GO-SH对初始浓度为4 mg.L-1的砷去除率达到97.7%;吸附等温线符合Langmuir和Freundlich模型,45℃时由Langmuir模型得到的饱和吸附量(Qm)为24.45 mg.g-1;吸附动力学符合准二级模型,内扩散模型符合高浓度砷的吸附动力学;热力学研究表明,吸附过程是自发吸热的反应,以化学吸附为主.     

A photolysis coefficient for characterizing the response of aqueous constituents to photolysis

UV photolysis and UV based advanced oxidation processes (AOPs) are gaining more and more attention for drinking water treatment. Quantum yield (ø) and molar absorption coefficient (ε) are the two critical parameters measuring the effectiveness of photolysis of a compound. The product of the two was proposed as a fundamental measure of a constituent’s amenability to transformation by photolysis. It was shown that this product, named the photolysis coefficient, k _p , can be determined using standard bench tests and captures the properties that govern a constituent’s transformation when exposed to light. The development showed the photolysis coefficient to be equally useful for microbiological, inorganic and organic constituents. Values of k _p calculated by the authors based on quantum yield and molar absorption coefficient data from the literature were summarized. Photolysis coefficients among microorganisms ranged from 8500 to more than 600000 and are far higher than for inorganic and organic compounds, which varied over a range of approximately 10 to 1000 and are much less sensitive to UV photolysis than the microorganisms.     

在Pt/Al2O3催化剂上甲醇深度氧化的稳态及非稳态动力学

用玻璃外循环无梯度反应器研究了在Pt/Al_2O_3催化剂上甲醇深度氧化稳态动力学,甲醇深度氧化稳态动力学服从L-H机理模型。用正交设计法估计了动力学方程中的参数。用脉冲法测定了甲醇、氧及CO_2的吸附热。用脉冲法研究了甲醇在催化剂上吸附量与停留时间的关系,实验中观察到在Pt/Al_2O_3催化剂上甲醇深度氧化的振荡现象。     

催化氧化技术治理苯化工装置和罐区含氮挥发性有机物废气

采用催化氧化技术对某石化企业苯胺、硝基苯等生产装置和罐区的含氮挥发性有机物(NVOCs)废气进行集中处理,建成了一套20 000 Nm~3/h规模的安全高效处理装置。采用自主研发的WSH-2N型蜂窝状Pt-Pd-Ce催化剂,在高效氧化有机物的同时,高选择性地将有机氮转化为N_2。运行结果表明,净化气非甲烷总烃质量浓度低于15 mg/m~3,非甲烷总烃去除率大于99%,NO_x质量浓度低于10 mg/m~3,苯、苯胺、硝基苯、环己烷等特征有机污染物浓度均低于检出限,各项指标优于国内外现有技术。     

UV/TiO_2膜深度处理垃圾渗滤液的研究

研究了以固定相TiO2为催化剂光催化降解垃圾渗滤液中有机污染物的可行性。试验了制备TiO2膜的适宜条件以及光照时间等各种因素对COD的去除率和UV335脱色率的影响。研究表明,COD为418mg/L的垃圾渗滤液经400W高压汞灯光照30min,COD的去除率和UV335脱色率分别为44.3%和75.0%。光照时间60min时,COD的去除率和UV335脱色率可提高至54%和90%。光照30min后与活性炭柱联用,COD的去除率和UV335脱色率分别提高到68.3%和84.6%。     

微电解+Fenton氧化+二级A/O组合工艺处理农药杀菌剂废水

杀菌剂生产废水含有大量三环唑、无机盐、高毒性物质和难生物降解有机物,对生化细菌有较强的抑制和毒害作用,且BOD5/COD值较小,采用传统生化处理工艺无法进行。现采用微电解、Fenton氧化和二级A/O组合工艺建成的废水处理工程,运行良好,出水各项指标达到环太湖流域排放标准DB 32/1072—2007。     

色基生产废水的三级处理工艺试验

在染料中间体红色基Ｂ，紫酱色基ＧＰ的生产过程中，全产生降解处理的废水，采用中和隔油－生物接触氧化－电解脱色工艺处理可达标准排放。试验结果表明，硝化废酸液和水解母液的混合废水经过中和隔油处理后，ＣＯＤｃｒ的去除率可达到５６％以上，而ＢＯＤ５／ＣＤＯｃｒ的比值可在从０．２２提高到０．５以上；再经生物接触氧化处理后，ＣＯＤｃｒ的去除率在８８％以上，ＢＯＤ５的去除率在９２％以上；最后，电解处理能使ＣＯＤｃ     

水解-生物接触氧化-化学投药工艺处理肉类加工废水

采用优势菌投入水解-生物接触氧化-化学投药法应用于肉类加工厂废水处理,通过工程实例,运行结果表明,处理出水水质能稳定达标,而且还具有投资费用少,运行费用低,管理方便等优点。