生物陶粒反应器的氢自养反硝化研究

利用氢自养反硝化生物陶粒反应器处理硝酸盐废水,探讨了生物陶粒反应器中氢自养反硝化生物脱氮的实现过程.考察了水力停留时间、进水硝氮负荷、进水pH值、温度、供氢量等因素对反应器脱氮效果的影响.结果表明,当水力停留时间为24 h和48 h时,反应器对硝酸氮的平均去除率分别达到94.54%和97.47%.在水力停留时间为5~16 h时,NO-3-N去除率随水力停留时间的缩短而降低;进水NO-3-N浓度较低时,NO-3-N的降解速率随其浓度的升高而增大,当NO-3-N浓度大于110mg·L-1时,氢自养反硝化反应受到抑制;中偏碱性环境较酸性或碱性环境更利于反应器对硝酸盐的去除;反应器有较宽的温度适应范围,最适温度为25~30℃;当反应器供氢不足时,脱氮效果明显降低,表明了氢自养反硝化菌对氢气利用的专一性.在整个运行阶段,出水中亚硝酸氮浓度一直保持在较低水平.     

环境因子对水蚯蚓呼吸速率的影响研究

水蚯蚓能通过摄食剩余污泥而使污泥减量.因此,本文以颤蚓科蠕虫 (Tubificidae)为研究对象,考察环境因子(水质、水蚯蚓投加量、温度、pH、溶解氧)对水蚯蚓呼吸速率的影响,以探明水蚯蚓生长和新陈代谢的最佳条件,揭示环境因子影响水蚯蚓污泥减量的机理.结果表明,水蚯蚓在"水蚯蚓-微生物"共生系统污泥减量装置出水中的呼吸速率最大,为81.72 mg·g^-1·h^-1·L^-1(以单位体积内每g干重水蚯蚓每小时消耗的O₂质量计(mg)),在蒸馏水中的呼吸速率最小,仅为18.31 mg·g^-1·h^-1·L^-1;在容积为1 L的系统中,水蚯蚓呼吸速率随着投加量增加而逐渐减小,当水蚯蚓投加量为0.25 g (以湿重计)时,呼吸速率最大,为81.72 mg·g^-1·h^-1·L^-1;在8~22℃范围内,水蚯蚓呼吸速率随温度升高而增大,在22~30℃范围内趋势则相反;当pH=8.00±0.05时呼吸速率最大,比其他pH值条件下测得的呼吸速率高1倍多;溶解氧在3.5~4.5 mg·L^-1范围内,水蚯蚓的呼吸速率较高,在此溶解氧范围之外时,水蚯蚓呼吸速率均较低. 该研究结果可为污泥减量中水蚯蚓的培养和应用提供可靠的理论依据,从内在层次上揭示了环境因子影响水蚯蚓生长及代谢,进而影响污泥减量的本质原因.     

温度对生物强化除磷工艺反硝化除磷效果的影响

以处理城市污水的中试规模生物强化除磷A2/O活性污泥工艺系统为研究对象,考察了温度对系统COD去除和脱氮除磷效果的影响,特别是温度对活性污泥反硝化除磷性能的影响.结果表明,当温度从(30.9±0.8)℃降低到(9.1±0.6)℃时,A2/O系统的脱氮除磷效果显著下降,系统对TN和TP的污泥去除负荷明显下降.通过污泥反硝化除磷活性实验发现,随着温度的降低,系统中活性污泥的最大厌氧释磷速率、最大好氧吸磷速率和最大缺氧吸磷速率都降低.活性污泥中反硝化除磷菌(DPB)占聚磷菌(PAOs)总量的比例随温度降低稍有下降,但平均值仍维持在47.5％左右.用阿伦尼乌斯公式对实验结果进行拟合,得到系统中活性污泥聚磷菌厌氧释磷反应活化能Ea1为148.0 kJ· mol-1,聚磷菌好氧吸磷反应活化能Ea2为228.8 kJ·mol-1,发生在缺氧条件下反硝化除磷菌的吸磷反应活化能Ea3为315.8 kJ·mol-1.对不同温度下污泥絮体粒径分析结果表明,随温度降低,粒径分布更加集中,系统中活性污泥絮体颗粒平均粒径减小,不利于污泥絮体内部反硝化除磷缺氧微环境的形成.     

高岭土负载纳米Fe/Ni同时去除水中Cu2+和NO3-

工业废水常含有不同污染物如重金属离子和无机阴离子,而如何有效去除复合污染物就成为环境科学前沿研究的挑战性课题.这些污染物因化学性质不同而导致去除机理和途径也不同.本文采用合成高岭土负载纳米双金属Fe/Ni(K-Fe/Ni)同步去除水中Cu2+和NO-3.结果表明K-Fe/Ni能有效去除水中Cu2+和NO-3,但它们的去除效果却会相互受到影响.在Cu2+浓度为200mg·L-1时,NO-3的去除率达到42.5%;而未加入Cu2+时,NO-3的去除率仅有26.9%,说明Cu2+的存在提高了NO-3降解效率.同样,水中NO-3的存在也影响Cu2+的去除(Cu2+去除率从99.7%降到96.5%).但NO-3浓度对去除Cu2+的影响小于Cu2+浓度对NO-3的影响.通过BET比表面积、X射线衍射(XRD)、扫描电镜(SEM)、X射线能量散射(EDS)和X射线光电分析(XPS)对K-Fe/Ni表征的结果显示,反应后K-Fe/Ni的表面存在铁的氧化物、Ni0和被还原的Cu0.基于以上结果,我们发现K-Fe/Ni同步去除水中Cu2+和NO-3的机理是:高岭土负载下的纳米Fe0作为还原剂,在Ni0的催化产氢作用下将Cu2+还原成Cu0并沉积在K-Fe/Ni上而形成纳米Fe/Ni/Cu三金属催化剂,从而加速催化水中NO-3降解.     

汽油在西北黄土上吸附特性的研究

通过动力学和热力学吸附实验,研究了汽油在西北地区黄土上的吸附行为,同时研究了提取的天然腐植酸对汽油在黄土上吸附行为的影响.结果表明,汽油在黄土上的吸附在6h内达到平衡.无论是否加入腐植酸,汽油在黄土上的吸附动力学过程均符合Elovich方程,其热力学吸附符合Freundlich方程.腐植酸的存在使汽油在黄土上的吸附能力减小.反应温度从25℃升高到45 C,汽油在土壤上的饱和吸附量从6.300mg·g-1减小到1.365 mg·g-1,表明汽油在黄土上的吸附属于放热反应.溶液pH和土壤粒径的增大,均不利于汽油在黄土上的吸附,溶液pH和土壤粒径越大,其在黄土上的吸附量越小.另外,在室温下对吸附了汽油的土壤样品和纯汽油挥发行为的研究表明,吸附了汽油的土壤样品的汽油挥发比纯汽油慢,其挥发率与时间成对数关系.     

Cost-performance analysis of nutrient removal in a full-scale oxidation ditch process based on kinetic modeling

A full-scale oxidation ditch process for treating sewage was simulated with the ASM2d model and optimized for minimal cost with acceptable performance in terms of ammonium and phosphorus removal. A unified index was introduced by integrating operational costs (aeration energy and sludge production) with effluent violations for performance evaluation. Scenario analysis showed that,in comparison with the baseline (all of the 9 aerators activated), the strategy of activating 5 aerators could save aeration energy significantly with an ammonium violation below 10%. Sludge discharge scenario analysis showed that a sludge discharge flow of 250–300 m3/day (solid retention time (SRT), 13–15 days) was appropriate for the enhancement of phosphorus removal without excessive sludge production. The proposed optimal control strategy was: activating 5 rotating disks operated with a mode of "111100100" ( "1"represents activation and "0" represents inactivation) for aeration and sludge discharge flow of 200 m3/day (SRT, 19 days). Compared with the baseline, this strategy could achieve ammonium violation below 10% and TP violation below 30% with substantial reduction of aeration energy cost (46%) and minimal increment of sludge production (< 2%). This study provides a useful approach for the optimization of process operation and control.     

Pollutant emission characteristics of rice husk combustion in a vortexing fluidized bed incinerator

Rice husk with high volatile content was burned in a pilot scale vortexing fluidized bed incinerator. The fluidized bed incinerator was constructed of 6 mm stainless steel with 0.45 m in diameter and 5 m in height. The emission characteristics of CO, NO, and SO2 were studied. The effects of operating parameters, such as primary air flow rate, secondary air flow rate, and excess air ratio on the pollutant emissions were also investigated. The results show that a large proportion of combustion occurs at the bed surface and the freeboard zone. The SO2 concentration in the flue gas decreases with increasing excess air ratio, while the NOx concentration shows reverse trend. The flow rate of secondary air has a significant impact on the CO emission. For a fixed primary air flowrate, CO emission decreases with the secondary air flowrate. For a fixed excess air ratio, CO emission decreases with the ratio of secondary to primary air flow. The minimum CO emission of 72 ppm is attained at the operating condition of 40% excess air ratio and 0.6 partition air ratio. The NOx and SO2 concentrations in the flue gas at this condition are 159 and 36 ppm, which conform to the EPA regulation of Taiwan.     

不同Fe(Ⅲ)对活性污泥异化铁还原及除磷影响研究

以SBBR反应器活性污泥作为铁还原菌菌种来源,采用兼性厌氧/严格厌氧恒温培养试验,投加不同Fe(Ⅲ)考察各条件下的异化铁还原能力同时比较对磷的去除效果.结果表明:2种条件下Fe(Ⅲ)还原能力具有较好的一致性,依次为:Fe(OH)3＞氧化铁皮＞青矿＞红矿,其中严格厌氧条件下较好.同时,除磷效果与其呈正相关,富集培养至7d,Fe(OH)3及氧化铁皮体系出水磷浓度均达到2mg/L以下,之后继续降低,最终达到0.5mg/L以下.结合异化铁还原除磷机理,可以证明,不同Fe(Ⅲ)表面吸附作用对TP的去除贡献较小,其主要作用为铁还原菌驱动下的化学沉淀去除.     

Quantitative analysis of microbial biomass yield in aerobic bioreactor

We have studied the integrated model of reaction rate equations with thermal energy balance in aerobic bioreactor for food waste decomposition and showed that the integrated model has the capability both of monitoring microbial activity in real time and of analyzing biodegradation kinetics and thermal-hydrodynamic properties. On the other hand, concerning microbial metabolism, it was known that balancing catabolic reactions with anabolic reactions in terms of energy and electron flow provides stoichiometric metabolic reactions and enables the estimation of microbial biomass yield (stoichiometric reaction model). We have studied a method for estimating real-time microbial biomass yield in the bioreactor during food waste decomposition by combining the integrated model with the stoichiometric reaction model. As a result, it was found that the time course of microbial biomass yield in the bioreactor during decomposition can be evaluated using the operational data of the bioreactor (weight of input food waste and bed temperature) by the combined model. The combined model can be applied to manage a food waste decomposition not only for controlling system operation to keep microbial activity stable, but also for producing value–added products such as compost on optimum condition.     

Degradation of monofluorophenols in water irradiated with gaseous plasma

Decomposition of aqueous monofluorophenols (MFPs) was investigated by contact glow discharge electrolysis (CGDE). During CGDE, both MFPs and the corresponding total organic carbon (TOC) in water were consumed smoothly, suggesting that carbon atoms of benzene nucleus could be eventually mineralized to inorganic carbon (IC). And all the fluorine atoms in the MFPs were equally converted to fluoride ions. Based on the primary intermediates from each starting materials, it showed that aromatic hydroxylation preferentially occurred at the para- or ortho- position to the phenolic OH group of each MFPs. The disappearance of both MFPs and TOC followed the first-order rate law. The apparent rate constants for the decay of MFPs were independent from the pK_a values of MFPs.