沉积物中多环芳烃和有机氯农药定量分析的质量保证和质量控制

以美国ＥＰＡ为方法为基础,进行了沉积物中多环芳烃和有机氯农药分析的质量保证和质量控制实验,采用回收率指示物控制回收率,用内标法定量。结果表明多环芳烃的指示物回收率为５０．６７－９７．３３％,目标化合物的回收率为５８．６７－９６．３３％,方法检测限为３．３０－９．２６μｇ．ｋｇ＾－１。     

几类有机污染物的微塑料/水分配系数的线性溶解能关系模型

水体中的微塑料会吸附其中的有机污染物,影响有机污染物和微塑料的环境归趋和生态毒性。研究微塑料对有机污染物的吸附行为,对于评价有机污染物和微塑料的环境赋存、迁移及生物有效性有重要意义。污染物在微塑料与水之间的平衡分配系数(Kd),是表征微塑料对有机污染物吸附能力的重要参数。实验方法难以逐个测定众多有机污染物的Kd值,有必要发展其预测模型。本研究搜集了有机污染物的线性溶解能关系(LSER)参数及Kd值,构建了可预测有机污染物在聚丙烯微塑料与海水、聚乙烯微塑料与海水、聚乙烯微塑料与淡水之间Kd值的LSER模型。模型具有良好的拟合优度(R2adj介于0.794~0.903)、稳健性(Q2LOO和Q2BOOT分别介于0.763~0.863和0.720~0.804)和预测能力(R2ext和Q2ext分别介于0.886~0.971和0.825~0.954),能够用于预测多氯联苯、多环芳烃、六氯环已烷和氯苯类有机污染物的Kd值。     

办公室地面灰尘中PAHs污染的时间变化规律及人体健康风险

为探究室内地面灰尘中15种多环芳烃(PAHs)污染的时间变化规律,于2012年3—7月对北京市一座办公楼内的某办公室进行了每周一次的连续高密度灰尘样品采集。利用高效液相色谱-荧光检测器检测15种PAHs含量。结果表明,该办公室内灰尘样品中∑PAHs浓度范围为1 180~24 300 ng·g~(-1),平均浓度为8 960 ng·g~(-1)。总体上,检出的PAHs以3环PAHs为主,其中菲占PAHs总量的59%以上,其次是4环和5环PAHs,4环PAHs中占的比重最高,约占4环PAHs总量的34%。该办公室内灰尘中∑PAHs的浓度存在显著的时间变化差异,总体表现为∑PAHs浓度随气温升高而降低的趋势。源解析结果显示,机动车排放源、石油源、木材与煤燃烧是北京市室内灰尘中PAHs的主要来源。健康风险评估结果显示,ILCR皮肤接触ILCR手口摄入,且CR均值大于10-6,说明该采样点的PAHs污染存在"潜在致癌风险"。     

土壤多环芳烃污染根际修复研究进展

多环芳烃(polycyclicaromatichydrocarbons,PAHs)是环境中普遍存在的具有代表性的一类重要持久性有机污染物,具“三致性”、难降解性,在土壤环境中不断积累,严重危害着土壤的生产和生态功能、农产品质量和人类健康。修复土壤多环芳烃污染已成为研究的焦点。根际修复是利用植物-微生物和根际环境降解有机污染物的复合生物修复技术,是目前最具潜力的土壤生物修复技术之一。对国内外学者近年来在土壤多环芳烃污染根际修复的效果、根际修复机理和根际修复的影响因素方面的研究进展作了较系统的综述,并分别分析了单作体系、混作体系、多进程根际修复系统和接种植物生长促进菌根际修复系统对土壤多环芳烃的修复效果。指出根际环境对PAHs的修复主要有3种机制:根系直接吸收和代谢PAHs;植物根系释放酶和分泌物去除PAHs,增加根际微生物数量,提高其活性,强化微生物群体降解PAHs。并讨论了影响根际修复PAHs的环境因素如植物、土壤类型、PAHs理化性质、菌根真菌以及表面活性剂等。植物-表面活性剂结合的根际修复技术、PAHs胁迫下根际的动态调节过程、运用分子生物学技术并结合植物根分泌物的特异性筛选高效修复植物以及植物富集的PAHs代谢产物进行跟踪与风险评价将成为未来研究的主流。     

森林新近凋落叶溶出DOM的性质及其对菲增溶作用的影响

凋落叶作为森林凋落物的主要组成部分,其溶出的大量有机质也是森林土壤可溶性有机质（DOM）的主要来源之一。研究森林凋落叶溶出DOM对PAHs增溶作用的影响有利于合理预测及评价森林土壤中PAHs的环境行为和生态风险。本研究采集了南亚热带常绿阔叶人工林的4种常见树种--尾叶桉（Eucalyptus urophylla）、木荷（Schima superba）、大叶相思（Acacia auriculiformis）和湿地松（Pinus elliottii）的新近凋落叶为试验材料,研究其DOM含量、组成与性质,对比分析了不同凋落叶DOM对菲的増溶作用及其与DOM性质的相关关系。结果表明,4种凋落叶的可溶性有机碳（DOC）质量分数在C 11.61~36.25 mg·g-1之间,其中尾叶桉的含量最大,湿地松最小。尾叶桉和木荷DOM的主要组分是可溶性糖（SS）和可溶性酚（SP）,两者总C量占DOC的比例超过47%,而大叶相思和湿地松中SS和SP两者总量所占比例均低于30%。另外,4种凋落叶DOM的质量分数（以C计）与其电导率的线性关系图中有明显转折点,说明它们均具有表面活性剂的性质。凋落叶DOM在临界胶束浓度（CMC）之上对菲具有不同程度的増溶作用,其与菲的结合系数（logKDOC）的大小顺序为尾叶桉（3.05 L·kg-1）＞木荷（3.02 L·kg-1）＞大叶相思（2.79 L·kg-1）＞湿地松（2.54 L·kg-1）,这表明尾叶桉和木荷DOM的增溶作用明显高于大叶相思和湿地松DOM。经分析表明,logKDOC与各DOM在254、280 nm处的特征紫外吸光度值（SUV-A254、SUV-A280）及其SS、SP的相对含量均呈显著正相关（p＜0.01）,与A240/A420、A254/A400比值呈显著负相关（p＜0.01）,说明DOM的芳香化程度越高,分子量越大, SS与SP所占比例越高,其对菲的増溶效果越明显。     

Polycyclic aromatic hydrocarbon (PAH) deposition to and exchange at the air-water interface of Luhu, an urban lake in Guangzhou, China

Urban lakes are vulnerable to the accumulation of semivolatile organic compounds, such as PAHs from wet and dry atmospheric deposition. Little was reported on the seasonal patterns of atmospheric deposition of PAHs under Asian monsoon climate. Bulk (dry + wet) particle deposition, air-water diffusion exchange, and vapour wet deposition of PAHs in a small urban lake in Guangzhou were estimated based on a year-round monitoring. The total PAH particle deposition fluxes observed were 0.44-3.46 μg m⁻² day⁻¹. The mean air-water diffusive exchange flux was 20.7 μg m⁻² day⁻¹. The vapour deposition fluxes of PAHs ranged 0.15-8.26 μg m⁻² day⁻¹. Remarkable seasonal variations of particulate PAH deposition, air-water exchange fluxes and vapour wet deposition were influenced by seasonal changes in meteorological parameters. The deposition fluxes were predominantly controlled by the precipitation intensity in wet season whereas by atmospheric concentration in dry season.     

Phytoremediation of polyaromatic hydrocarbons, anilines and phenols

Phytoremediation technologies based on the combined action of plants and the microbial communities that they support within the rhizosphere hold promise in the remediation of land and waterways contaminated with hydrocarbons but they have not yet been adopted in large-scale remediation strategies. In this review plant and microbial degradative capacities, viewed as a continuum, have been dissected in order to identify where bottle-necks and limitations exist. Phenols, anilines and polyaromatic hydrocarbons (PAHs) were selected as the target classes of molecule for consideration, in part because of their common patterns of distribution, but also because of the urgent need to develop techniques to overcome their toxicity to human health. Depending on the chemical and physical properties of the pollutant, the emerging picture suggests that plants will draw pollutants including PAHs into the plant rhizosphere to varying extents via the transpiration stream. Mycorrhizosphere-bacteria and -fungi may play a crucial role in establishing plants in degraded ecosystems. Within the rhizosphere, microbial degradative activities prevail in order to extract energy and carbon skeletons from the pollutants for microbial cell growth. There has been little systematic analysis of the changing dynamics of pollutant degradation within the rhizosphere; however, the importance of plants in supplying oxygen and nutrients to the rhizosphere via fine roots, and of the beneficial effect of microorganisms on plant root growth is stressed. In addition to their role in supporting rhizospheric degradative activities, plants may possess a limited capacity to transport some of the more mobile pollutants into roots and shoots via fine roots. In those situations where uptake does occur (i.e. only limited microbial activity in the rhizosphere) there is good evidence that the pollutant may be metabolised. However, plant uptake is frequently associated with the inhibition of plant growth and an increasing tendency to oxidant stress. Pollutant tolerance seems to correlate with the ability to deposit large quantities of pollutant metabolites in the 'bound' residue fraction of plant cell walls compared to the vacuole. In this regard, particular attention is paid to the activities of peroxidases, laccases, cytochromes P450, glucosyltransferases and ABC transporters. However, despite the seemingly large diversity of these proteins, direct proof of their participation in the metabolism of industrial aromatic pollutants is surprisingly scarce and little is known about their control in the overall metabolic scheme. Little is known about the bioavailability of bound metabolites; however, there may be a need to prevent their movement into wildlife food chains. In this regard, the application to harvested plants of composting techniques based on the degradative capacity of white-rot fungi merits attention.     

A PCE groundwater plume discharging to a river: influence of the streambed and near-river zone on contaminant distributions

An investigation of a tetrachloroethene (PCE) groundwater plume originating at a dry cleaning facility on a sand aquifer and discharging to a river showed that the near-river zone strongly modified the distribution, concentration, and composition of the plume prior to discharging into the surface water. The plume, streambed concentration, and hydrogeology were extensively characterized using the Waterloo profiler, mini-profiler, conventional and driveable multilevel samplers (MLS), Ground Penetrating Radar (GPR) surveys, streambed temperature mapping (to identify discharge zones), drivepoint piezometers, and soil coring and testing. The plume observed in the shallow streambed deposits was significantly different from what would have been predicted based on the characteristics of the upgradient plume. Spatial and temporal variations in the plume entering the near-river zone contributed to the complex contaminant distribution observed in the streambed where concentrations varied by factors of 100 to 5000 over lateral distances of less than 1 to 3.5 m. Low hydraulic conductivity semi-confining deposits and geological heterogeneities at depth below the streambed controlled the pattern of groundwater discharge through the streambed and influenced where the plume discharged into the river (even causing the plume to spread out over the full width of the streambed at some locations). The most important effect of the near-river zone on the plume was the extensive anaerobic biodegradation that occurred in the top 2.5 m of the streambed, even though essentially no biodegradation of the PCE plume was observed in the upgradient aquifer. Approximately 54% of the area of the plume in the streambed consisted solely of PCE transformation products, primarily cis-1,2-dichloroethene (cDCE) and vinyl chloride (VC). High concentrations in the interstitial water of the streambed did not correspond to high groundwater-discharge zones, but instead occurred in low discharge zones and are likely sorbed or retarded remnants of past high-concentration plume discharges. The high-concentration areas (up to 5529 microg/l of total volatile organics) in the streambed are of ecological concern and represent potential adverse exposure locations for benthic and hyporheic zone aquatic life, but the effect of these exposures on the overall health of the river has yet to be determined. Even if the upgradient source of PCE is remediated and additional PCE is prevented from reaching the streambed, the high-concentration deposits in the streambed will likely take decades to hundreds of years to flush completely clean under natural conditions because these areas have low vertical groundwater flow velocities and high retardation factors. Despite high concentrations of contaminants in the streambed, PCE was detected in the surface water only rarely due to rapid dilution in the river and no cDCE or VC was detected. Neither the sampling of surface water nor the sampling of the groundwater from the aquifer immediately adjacent to the river gave an accurate indication of the high concentrations of PCE biodegradation products present in the streambed. Sampling of the interstitial water of the shallow streambed deposits is necessary to accurately characterize the nature of plumes discharging to rivers.     

Environmental monitoring of complex hydrocarbon mixtures in water and soil samples after solid phase microextraction using PVC/MWCNTs nanocomposite fiber

A novel nanocomposite based on incorporation of multiwalled carbon nanotubes (MWCNTs) in polyvinyl chloride (PVC) was prepared. Proposed nanocomposite was coated on stainless steel wire by deep coating. Composition of nanocomposite was optimized based on results of morphological studies using scanning electron microscopy. The best composition (83% MWCNTs:17% PVC) was applied as a solid phase microextraction fiber. Complex mixture of aromatic (BTEX) and aliphatic hydrocarbons (C₅–C₃₄) were selected as model analytes, and performance of proposed fiber in extraction of the studied compounds from water and soil samples was evaluated. Analytical merits of the method for water samples (LODs = 0.10–1.10 ng L⁻¹, r² = 0.9940–0.9994) and for soil samples (LODs = 0.10–0.77 ng kg⁻¹, r² = 0.9946–0.9994) showed excellent characteristics of it in ultra trace determination of petroleum type environmental pollutants. Finally, the method was used for determination of target analytes in river water, industrial effluent and soil samples.     

Effect of housing geometry on the performance of Chemcatcher passive sampler for the monitoring of hydrophobic organic pollutants in water

Passive sampling of pollutants in water has been gaining acceptance for environmental monitoring. Previously, an integrative passive sampler (the Chemcatcher) was developed and calibrated for the measurement of time weighted average concentrations of hydrophobic pollutants in water. Effects of physicochemical properties and environmental variables (water temperature and turbulence) on kinetic and thermodynamic parameters characterising the exchange of analytes between the sampler and water have been published. In this study, the effect of modification in sampler housing geometry on these calibration parameters was studied. The results obtained for polycyclic aromatic hydrocarbons show that reducing the depth of the cavity in the sampler body geometry increased the exchange kinetics by approximately twofold, whilst having no effect on the correlation between the uptake and offload kinetics of analytes. The use of performance reference compounds thus avoids the need for extensive re-calibration when the sampler body geometry is modified.