Spatial allocation of material flow analysis in residential developments: a case study of Kildare County,Ireland

Studies of urban metabolism provide important insights for environmental management of cities, but are not widely used in planning practice due to a mismatch of data scale and coverage. This paper introduces the Spatial Allocation of Material Flow Analysis (SAMFA) model as a potential decision support tool aimed as a contribution to overcome some of these difficulties and describes its pilot use at the county level in the Republic of Ireland. The results suggest that SAMFA is capable of identifying hotspots of higher material and energy use to support targeted planning initiatives, while its ability to visualise different policy scenarios supports more effective multi-stakeholder engagement. The paper evaluates this pilot use and sets out how this model can act as an analytical platform for the industrial ecology–spatial planning nexus.     

危险品运输网络优化设计研究综述

为分析当今反恐新形势下的危险品运输网络优化设计问题的研究现状,系统总结国内外关于一般场景和恐怖袭击威胁2种情况下危险品运输网络优化设计研究的主要模型和方法,梳理两者现有的研究内容,并讨论其共性及恐怖袭击威胁情景下的研究的新特点。结果发现:目前关于解决危险品运输网络优化设计问题模型的鲁棒性研究较为缺乏,尤其是模型在更为复杂和不确定性更强的恐怖袭击情景中适用性不强;危险品运输的鲁棒优化模型即使在突发事件条件下,也可以使决策者能够作出相对满意的决策;鲁棒性危险品运输网络能够规避风险扰动,可用来防止在恐怖袭击中因危险品车辆爆炸等造成更大的危害。     

Preparation of steel slag porous sound-absorbing material using coal powder as pore former

The aim of the study was to prepare a porous sound-absorbing material using steel slag and fly ash as the main raw material, with coal powder and sodium silicate used as a pore former and binder respectively. The influence of the experimental conditions such as the ratio of fly ash, sintering temperature, sintering time, and porosity regulation on the performance of the porous sound-absorbing material was investigated. The results showed that the specimens prepared by this method had high sound absorption performance and good mechanical properties, and the noise reduction coefficient and compressive strength could reach 0.50 and 6.5 MPa, respectively. The compressive strength increased when the dosage of fly ash and sintering temperature were raised. The noise reduction coefficient decreased with increasing ratio of fly ash and reducing pore former, and first increased and then decreased with the increase of sintering temperature and time. The optimum preparation conditions for the porous sound-absorbing material were a proportion of fly ash of 50% (wt.%), percentage of coal powder of 30% (wt.%), sintering temperature of 1130°C, and sintering time of 6.0 hr, which were determined by analyzing the properties of the sound-absorbing material.     

关于焦化行业CO2排放核算方法的探讨

本文分析了适用于焦化行业通用CO₂排放核算方法,在此基础上结合我国焦化行业工艺和原料的特征,采用排放因子法和物料衡算法等两种方法对10家典型焦化企业CO₂排放进行核算。结果表明:物料衡算法能很好地反映不同类型焦化企业的排放特征;排放因子法对我国独立焦化企业存在碳排放量系统性高估的可能。为此,建议我国焦化企业可借鉴德国焦化企业的碳核算经验,采用碳平衡法对不同类型的焦化企业(单元)的碳排放量进行核算,并完善相关的统计和监测技术。     

多种复合材料固定化反应器的对比研究

选用活性炭、海砺壳2种材料作为固定化载体,对改良型UASB系统去除COD的性能进行研究,结果表明选择既高柱又循环且增加载体填充体积的系统,可有效去除高浓度有机废水的COD,但当填充载体过高时,循环系统难以实现,并存在憋气的可能。     

Molecularly imprinted polymer for analysis of trace atrazine herbicide in water

A molecularly imprinted polymer (MIP) for atrazine was synthesized by non-covalent method. The binding capacity of MIP was 1.00 mg g^{? 1} polymer. The selectivity and recovery were investigated with various pesticides which are mostly, found in the environment, for both similar and different chemical structure of atrazine. The competitive recognition between atrazine and structurally similar compounds was evaluated and it was found that the system provided highest recovery and selectivity for atrazine while low recovery and selectivity were obtained for the other compounds. The highest recovery was obtained from MIP compared with non-imprinted polymer (NIP), a commercial C₁₈ and a granular activated carbon (GAC) sorbent. The method provided high recoveries ranged from 94 to 99% at two spiked levels with relative standard deviations less than 2%. The lower detection limit of the method was 80 ng L^{? 1}. This method was successfully applied for analysis of environmental water samples.     

城市废物的回收处理与利用

当前世界各国均面临着“废弃物”所造成的环境污染问题。本文列举了一些国家“废弃物”的排放以及回收利用情况,并举例说明对变废为宝的技术路线和应该采取的措施。     

上海市经济-环境系统的物质输入分析

对区域或城市经济-环境系统的物质输入分析。可以判断可持续发展所处的状态。进而为区域或城市制定循环经济发展战略提供依据。利用物质流的理论和方法．依据欧盟指导原则，分析了1990—2003年间上海市经济-环境系统的物质总需求和资源生产率等主要指标。研究结果表明：①上海市巨大的物质总需求和直接物质消耗给上海市的生态环境带来了巨大的压力；②1996年上海市的资源生产率是全国的1．22倍．但2000年日本的资源生产率是上海市的36倍；③影响上海市的物质总需求或者环境质量的关键因素是技术和制度能力。在上述的分析基础上。提出在2020年之前上海市发展循环经济要注重于输入端的减物质化和加强循环绍济的技术支撑研究与开发以及制度能力建设。     

粉煤灰基质滤料生物过滤处理生活污水研究

将粉煤灰基质滤料用于曝气生物滤池,该滤料具有较高的比表面积和孔隙率,吸附性能良好,挂膜后生物相丰富。对于中等浓度的生活污水,当水力负荷和COD有机物负荷分别控制在1.53 m3/(m2.h)、3.68 kg/(m3.d)以下时,该曝气生物滤池COD和NH3-N去除率能稳定在85%以上,出水COD和NH3-N达到排放标准要求。该曝气生物滤池对进水水质水量的变动具有较强的抗冲击负荷能力。     

天然胶/公共网络/废胶粉互穿聚合物网络

通过互穿聚合物网络技术成功制备了天然橡胶/公共网络/废胶粉共轭三组分,并测定了力学性能和微观形态。结果表明:当A/B摩尔比为2/1、AB含量为4.5%、废胶粉粒径为60目、废胶粉含量为15%时,体系的力学性能最好,共轭三组分天然橡胶/公共网络/废胶粉体系的磨耗体积明显低于两组分天然橡胶/废胶粉体系的磨耗体积。界面共轭互穿改善了界面结合,可减少反复压缩过程中的相间摩擦生热和变形。