厌氧氨氧化工艺脱氮及其污泥形态的研究

为研究厌氧氨氧化工艺对高浓度含氮废水的脱氮性能,在以聚乙烯海绵作为填料的上流式厌氧固定床反应器中利用人工配置高浓度含氮废水进行了实验研究.实验中通过添加充足无机碳源,实现了厌氧氨氧化反应器在总氮浓度900～1 210 mg/L长期稳定的运行,脱氮效率在80％以上,最高氮负荷为5.9 kg/m3·d.结果表明:充足的无机碳源在一定程度上可有效地降低高浓度亚硝氮对厌氧氨氧化菌的抑制作用.通过对污泥性状的研究,明确寻找出污泥上浮的原因所在.通过Stover-Kincannon模型确定系统动力学参数KB和Umax分别为30.2 g/L·d和2L2g/L·d,这将有助于对该厌氧氨氧化系统各控制条件的有效调节和准确设定,也为日后应用于实际工程中提供重要的理论依据.     

Application of CGP-cross route process for microstructure refinement and mechanical properties improvement in steel sheets

A modified method of severe plastic deformation (SPD) entitled constrained groove pressing-cross route (CGP-CR) was introduced for imposing a high magnitude of equivalent strain of about 2.32 per pass on the sheet form samples. The major benefit of this improved route compared to previous common route was the more homogeneity of strain in the rolling (RD) and transverse (TD) directions of sheets. In this study, low carbon steel samples were used for examination of evolutions in microstructure and mechanical properties during SPD via CGP-CR process. Mechanical properties improvement were measured by tensile and macro hardness tests. The results indicate that CGP-CR process can effectively improve tensile strength; and also, yield stress and hardness of as-received low carbon steel samples were improved up to about 100% after two deformation passes. Also, high magnitude of inhomogeneity can be observed in hardness distribution through first pass of the process which diminishes in the subsequent passes. Microstructural evolutions during process were monitored by optical microscopy observations and X-ray diffraction analysis. The results demonstrate that initial ferritic microstructure with grain size of about 30 μm was refined to a 225 nm cell structure after two passes of CGP-CR process.     

Modulation-assisted high speed machining of compacted graphite iron (CGI)

The application of controlled, low-frequency modulation (～100 Hz) superimposed onto the cutting process in the feed-direction – modulation-assisted machining (MAM) – is shown to be quite effective in reducing the wear of cubic boron nitride (CBN) tools when machining compacted graphite iron (CGI) at high machining speeds (>500 m/min). The tool life is at least 20 times greater than in conventional machining. This significant reduction in wear is a consequence of the multiple effects realized by MAM, including periodic disruption of the tool–workpiece contact, formation of discrete chips, enhanced fluid action and lower cutting temperatures. The propensity for thermochemical wear of CBN, the principal wear mode at high speeds in CGI machining, is thus reduced. The tool wear in MAM is also found to be smaller at the higher cutting speeds (730 m/min) tested. The feed-direction MAM appears feasible for implementation in industrial machining applications involving high speeds.     

土地利用变化对土壤硝化及氨氧化细菌区系的影响

以西藏高原相邻的原始森林、天然草原和农田土壤为研究对象,分别采用室内培养法和nested PCR-DGGE技术,对比研究了这3个生态系统的土壤硝化势、硝态氮浓度以及土壤氨氧化细菌（AOB）菌群区系.结果表明,农田土壤的硝化势和硝态氮（NO 3--N）浓度显著高于相邻的草原和森林土壤,硝化势分别是森林和草原土壤的9倍和11倍,NO 3--N是农田土壤无机氮（Nmin）的主要成分,占无机氮的70%～90%.铵态氮（NH 4＋-N）则是森林和草原土壤中主要的无机氮形态.原始森林和天然草原间的硝化势和硝态氮浓度没有显著差异.原始森林的土壤AOB菌群数量、多样性及均匀度最低.天然草原生态系统转换为农田后,土壤AOB菌群的多样性和均匀度显著降低,但是农田土壤的AOB菌群结构仍与其前身草原生态系统有较高的相似性.原始森林的AOB菌群数量、多样性及均匀度最低直接导致了其硝化势最低;农田土壤的硝化势和硝态氮浓度最高意味着农田生态系统中优势AOB的活性最高.以上结果表明,土地利用变化导致土壤氮素内循环及其关键微生物AOB的多样性与活性均发生显著变化,这些变化会影响土壤环境质量以及生态系统的持续与稳定.     

不同TS浓度互花米草沼渣二次发酵特性研究

中温（35±1）℃条件下,沼渣经6%的NaOH常温下处理48 h后,在TS含量8%、10%、12%的条件下沼气发酵.分析了发酵过程中日产气量、累积产气量、甲烷含量、pH值、挥发性脂肪酸（VFA）的变化,从不同角度考察TS含量负荷对沼渣二次发酵特性的影响.单位TS的日产气高峰分别达10、14、13 mL.g-1,累积产气率为217、227、228 mL.g-1,甲烷含量均在65%以上.发酵过程中最低pH为7.04.乙酸浓度最高分别为3 364、3 286、5 728 mg.L-1,丙酸和丁酸浓度均低于1 100 mg.L-1.结果表明,沼渣为难降解有机物,分解缓慢,不易出现酸化现象,但仍具有较强的产气潜力.     

北京城乡结合地空气中挥发性有机物健康风险评价

采用低温固体吸附采样,热脱附-气相色谱-质谱方法对北京城乡结合地空气中挥发性有机物（VOCs）进行了观测分析,并利用国际公认的健康风险评价四步法评价模型,对北京城乡结合地空气中挥发性有机物的健康风险进行了初步评价.结果表明,芳香族类的非致癌风险值在10-4～10-1数量级,卤代烃的非致癌风险值在10-4～10-5数量级,挥发性有机污染物的非致癌风险系数〈1,不会对暴露人群健康造成明显的非致癌危害.但苯的致癌指数较高（2.21×10-5）,超过了USEPA的建议值（1×10-6）,可能对人体健康造成潜在危害.在一年四季的健康风险中,冬季VOCs的健康风险最高,秋季次之,夏季最低.