CFD analysis on the performance of a solar chimney power plant system: Case study in Algeria

The solar chimney power plant (SCPP) is a power generator which uses solar radiation to increase the internal energy of the air circulating in the system, thereby transforming the useful gain of the solar collector into kinetic energy. The produced kinetic energy then can be converted into electrical energy by means of an appropriate turbine. In this paper, four locations in Algeria

(Constantine, Ouargla, Adrar, and Tamanrasset) were considered as case studies to describe the SCPP mechanism in detail. Numerical simulation of an SCPP which has the same geometrical dimensions was performed to estimate the power output of SCPP in these regions. Using the CFD software FLUENT we simulated a two-dimensional axisymmetric model of a SCPP with the standard k-ε turbulence model. The simulation results show that the highest power output produced monthly average value 68–73 KW over the year and the highest hourly power produced in June is around 109–113 KW.     

Comparison of refrigerated warehouse energy demand with R-717 and R-507 using eQUEST model

Natural refrigerant ammonia R-717 and synthetic azeotropic refrigerant R-507 (a blend containing 50% R-143a and 5% R-125 by weight) are used in a wide range of refrigeration systems especially in low-temperature applications. R-717 and R-507 are ozone friendly refrigerants, which have no Ozone Depletion Potential (ODP). Global Warming Potential (GWP) of R-717 and R-507 is equal to zero and 3300, respectively. The high amount of R-507 GWP demonstrates its negative effect on the Earth’s climate change. In this study, a refrigerated warehouse located in Cincinnati, Ohio was modeled and the total energy demand and Coefficient of Performance (COP) was evaluated by eQUEST using two scenarios. The R-717 and R-507 were used as refrigerant in the first and second scenarios, respectively. The results showed that using R-717 in the refrigeration system leads to a 15% energy saving and a higher COP compared to R-507 in all working conditions. The only exception is that at an evaporating temperature below ?35°C which COP values of both refrigerants are approximately equal.     

Evaluation of energy savings by using high efficiency motors in a thermal power station

This paper presents potential energy savings by installing high-efficiency motors instead of existing ones and their impact on greenhouse gases emissions reductions. This research study of the energy efficiency of electric motors has been performed in a typical thermal power plant. In the literature, the focus has been mainly on separate and away electric motors from operating facilities. The important advantage of this paper over other studies is that it uses the actual motors’ efficiency in the evaluation. The gains both in terms of electrical energy savings and in terms of financial economy by using high-efficiency motors have been discussed. As a result, the energy saving can be expected as 12.6% at the operating rate. This excellent result also reduces greenhouse gas emission by 1,423 tons every year. The analysis of the data provided an overview on energy losses often generated by the degradation and rewinding of electrical motors. This study represents very encouraging results that will help energy managers of industrial plants to become more involved in energy efficiency strategies.     

Triple-objective optimal sizing based on dynamic strategy for an islanded hybrid energy microgrid

A triple-objective optimal sizing method based on a dynamic strategy is presented for an islanded hybrid energy microgrid, consisting of wind turbine, solar photovoltaic, battery energy storage system and diesel generator. The dynamic strategy is given based on a dynamic complementary coordination between two different master-slave control modes for maximum renewable energy utilization. Combined with the proposed strategy, NSGA-II-based optimization program is applied to the sizing optimization problem with triple different objectives including the minimization of annualized system cost, the minimization of loss of power supply probability and the maximization of utilization ratio of renewable energy generation. The sizing results and the proposed strategy are both compared and analyzed to validate the proposed method in a real case of an islanded hybrid energy microgrid on Dong’ao Island, China.     

Fabrication and characterization of electrospun porous cellulose acetate nanofibrous mats incorporated with capric acid as form-stable phase change materials for storing/retrieving thermal energy

Electrospun cellulose acetate (CA) nanofibrous mats incorporated with capric acid was studied to fabricate form-stable phase change materials (PCMs) for storing/retrieving thermal energy. Electrospun CA nanofibrous mats with different porous structures and specific surface areas were firstly prepared through regulating the volume ratio of mixture solvent of acetone/dichloromethane (DCM). Effects of different volume ratio of mixture solvent and mat thickness on the morphological structure, specific surface area, and absorption capacity of CA nanofibrous mats were systematically investigated. The results indicated that CA nanofibrous mats were highly porous on the surface; hence, they were capable of absorbing a large amount of capric acid. The maximum absorption capacity of CA mats via electrospinning with volume ratio of acetone/DCM being 5/5 was ~95.8 wt%, due to its higher specific surface area of ~17.1 m²/g. The specific surface area and capric acid absorption capacity of CA nanofibrous mats increased with the increases of mat thickness. As the thickness of nanofibrous mats increased from 10 to 85 μm, the corresponding specific surface area and capric acid absorption capacity of mats increased respectively from 7.2 to 29.0 m²/g and 92.1 to 98.5%. Morphological structures, as well as the properties of thermal energy storage and thermal insulation of the fabricated form-stable PCMs, were studied by scanning electron microscopy, differential scanning calorimetry, and measurement of freezing times, respectively. The results indicated that the resulting form-stable PCMs could well maintain their phase transition characteristics and demonstrated great thermal energy storage capability and temperature regulation ability.     

Global solar radiation and energy yield estimation from photovoltaic power plants for small loads

Daily global solar radiation on a horizontal surface and duration of sunshine hours have been determined experimentally for five meteorological stations in Saudi Arabia, namely, Abha, Al-Ahsa, Al-Jouf, Al-Qaisumah, and Wadi Al-Dawaser sites. Five-years of data covering 1998–2002 period have been used. Suitable Angstrom models have been developed for the global solar radiation estimation as a function of the sunshine duration for each respective sites. Daily averages of monthly solar PV power outputs have been determined using the Angstrom models developed. The effect of the PV cell temperature on the PV efficiency has been considered in calculating the PV power output. The annual average PV output energy has been discussed in all five sites for small loads. The minimum and maximum monthly average values of the daily global solar radiation are found to be 12.09 MJ/m²/d and 30.42 MJ/m²/d for Al-Qaisumah and Al-Jouf in the months of December June, respectively. Minimum monthly average sunshine hours of 5.89 hr were observed in Al-Qaisumah in December while a maximum of 12.92 hr in Al-Jouf in the month of June. Shortest range of sunshine hours of 7.33–10.12 hr was recorded at Abha station. Minimum monthly average Solar PV power of 1.59 MJ/m²/day was obtained at Al-Qaisumah in the month of December and a maximum of 3.39 MJ/m²/day at Al-Jouf in June. The annual PV energy output was found to be 276.04 kWh/m², 257.36 kWh/m², 256.75 kWh/m², 245.44 kWh/m², and 270.95 kWh/m² at Abha, Al-Ahsa, Al-Jouf, Al-Qaisumah, and Wadi Al-Dawaser stations, respectively. It is found that the Abha site yields the highest solar PV energy among the five sites considered.     

Climate justice and energy: applying international principles to UK residential energy policy

This paper draws on climate justice principles developed in the context of international negotiations between national governments to assess the distribution of carbon reduction roles between different actors involved in residential energy use within the UK. In so doing, it aims to provide a new understanding of equity aspects of current residential policy and to highlight opportunities for more effective and equitable policy. The paper uses three criteria: rights and corresponding duties; mitigation responsibilities and capabilities. It applies them systematically to assess the roles of five key actors involved in residential energy use in the UK. The assessment finds a suboptimal distribution of actors’ duties, responsibilities and capabilities and roles and discusses whether and how a more effective and fair allocation of outcomes, in terms of carbon reduction and fuel poverty, could be achieved. In particular, it raises questions about whether the right actors are being legally obliged or incentivised to deliver energy efficiency improvements, and suggests that particular actors – local authorities and community groups – are under-used and require greater government support with capability. The paper represents the first use of international climate justice frameworks to investigate residential energy policy within a country.     

Wind energy potential analysis for Thailand: Uncertainty from wind maps and sensitivity to turbine technology

Rapid development of wind energy has been witnessed in Thailand. However, different wind resource maps (over land) have brought great uncertainty to wind energy planning. Here, four important mesoscale wind maps were considered: DEDP (2001), World Bank (2001), Manomaiphiboon et al. (2010) of JGSEE, and DEDE (2010). The wind maps were first harmonized to a common grid at 100 m and then compared. The earlier wind maps (DEDP and World Bank) are shown to represent the lower and upper limits of predicted speed, respectively, while JGSEE and DEDE tend to be more moderate with predictions statistically closer to observations. A consolidated wind map was constructed based on their median and shown to have the best prediction performance. It was then used for the technical potential analysis, in which three large (2-MW) turbine models (two conventional and one designed for low wind speed) were considered. By GIS techniques, any land areas not feasible for large wind turbines were excluded, and the corresponding overall onshore technical potential ranges between 50 and 250 GW, depending on map and turbine model. Considering only economically feasible turbines (with capacity factors of 20%) and the median-based map, the final technical potential equals 17 GW when using the low-wind-speed model but is reduced to 5 GW with the conventional models, adequately meeting the national wind energy target of 3 GW by the year 2036. The results suggest a strong sensitivity of estimated technical potential to turbine technology and a suitability of low-wind-speed turbines for wind conditions in Thailand.     

Energy and exergy analysis of a heat storage tank with a novel eutectic phase change material layer of a solar heater system

Solar energy is one of the most important renewable energy sources, but it is not available every time and every season. Thus, storing of solar energy is important. One of the popular methods of heat storage is use of phase change materials (PCMs) which have large thermal energy storage capacity. In this study, the heat storage tank in a domestic solar water heating system was chosen as control volume. The experiments were performed in the province of Elaz?g, Turkey, in November when solar radiation was weak due to cloudy sky. The heat storage tank of the system was modified to fill PCM between insulation and hot water part. A few PCMs which are Potassium Fluoride, Lithium Metaborate Dihydrate, Strontium Hydroxide Octahydrate, Barium Hydroxide Octahydrate, Aluminum Ammonium Sulfate, and Sodium Hydrogen Phosphate were analyzed to proper operating conditions using a Differential Scanning Calorimeter (DSC) and the best PCM was obtained with the Aluminum Ammonium Sulfate and Sodium Hydrogen Phosphate mixture. Thus, eutectic PCM was obtained and used in a heat storage tank of the solar water heating system. Energy and exergy analysis of heat storage tank was performed with and without the PCM. Energy and exergy analysis has shown that the heat storage tank with the PCM is more efficient than without the PCM and the maximum exergy efficiency was obtained as 22% with the heat storage tank with the PCM.     

Assessment of thermodynamics performance with sustainable propulsion indicators of a seaplane engine for different temperatures in the same altitude

Seaplanes have become an important tool along with rapidly developing technology in modern transportation for many countries related to sea. Considering the environmental evaluation for these aircraft, decreasing fossil fuels consumption and energy efficiency are important points for sustainability. For this purpose, in this study, first, the energy and exergy analyses based on the real data of a turboprop engine used in seaplane taken as the reference were performed. Then, new indicators developed for the sustainable propulsion index were examined and evaluated separately. The analyses were made for an altitude of 9000 ft and three different dead state temperatures of ?33°C, ?3°C, and 27°C. According to the analyses, while the average energy efficiencies were found to be 34.7%, 37.8%, and 40.7%, the average exergy efficiencies were found to be 19.24%, 21.25%, and 23.20%, respectively. In addition, the improvement potential due to irreversibility and entropy production for each case was also calculated and the results of the sustainable emission index were found to be very low. At the end of the study, the results were evaluated and some suggestions for the effective use of energy in the seaplanes were made.