非耐短路变压器短路和过载保护试验的自动测试系统

针对变压器产品认证标准GB 19212.1(IEC 61558-1)中关于"短路和过载保护"的型式试验项目,研发了一套智能自动测试系统。对于两种类型的非耐短路变压器,即输入保护和输出保护类型,分别给出了系统软硬件配置和详细的测试操作流程。相比传统手动测试方式,该系统的应用可显著减少人员在线时间,同时降低人工测量环节的不确定度。     

嗜酸菌对废旧印刷线路板金属铜的浸出研究

选用嗜酸性氧化亚铁硫杆菌(Acidithiobacillus ferrooxidans,简称T.f)、氧化硫硫杆菌(Thiobacillus thiooxidans,简称T.t)作为实验菌种研究其对线路板(Printed circuit board)粉金属铜的浸出;试验以单一菌种、混合菌种、无菌培养基及酸性蒸馏水进行浸出实验研究,通过对比不同条件下的浸出效果,得出单一氧化亚铁硫杆菌(T.f)的浸出效果最好,浸出率达到92.1%。通过对浸出过程中pH、ORP及Fe2+、Fe3+变化分析,发现Fe3+的氧化作用在铜的浸出过程中起主导作用,酸浸也有一定的贡献;对浸出后残余的PCB进行XRD及SEM观察分析发现,PCB组成成分中含有大量的酚烃、苯酚及邻、对位取代酚以及少量的长链烷烃及其脂肪烃,此类有机物在浸出过程中均与细菌或其代谢物发生了作用。     

航空电连接器腐蚀退化仿真研究

目的 探索当航空电连接器腐蚀退化时,其接触阻抗的变化规律,研究航空电连接器腐蚀退化对信号传输的影响规律。方法 首先对航空电连接器腐蚀退化的机理进行研究,建立其等效电路模型,然后分别对低频电连接器和射频电连接器进行仿真研究,提取阻抗参数,分析腐蚀退化对信号传输的影响规律。结果 接触电阻随着腐蚀程度的加深明显增大,接触电感随着腐蚀程度的加深变化不大,接触电容随着接触面腐蚀面积的增大而增大,随接触面间腐蚀厚度的增加而减小。接触电阻随频率的增加而增大,接触电感和接触电容随频率的增大基本保持不变。接触阻抗在低频时呈现感性特征,高频时呈现容性特征,阻抗幅值随频率的增加先增大、后减小,峰值出现在感性和容性转换频率处,腐蚀退化将使该转换频率减小。结论 对于低频信号,腐蚀退化将导致信号的衰减和延迟;对于高频信号,在转换频率处,信号的回波损耗、插入损耗和电压驻波比出现极值。     

废印刷线路板回收利用的现状与存在的问题

从分析印刷线路板材料构成的复杂性人手,论述了国内外在废印刷线路板回收处理技术方面的研究现状和进展。找出目前我国在处理废印刷线路板方面存在的问题与差距．并提出切实可行的建议。分析表明,干法分离分选技术应是今后的发展方向。     

Nylon 6,6 modified screen printed carbon electrodes as electrochemical sensors for rapid chlorothalonil determination in water samples using differential pulse cathodic stripping voltammetry

A newly developed electrochemical sensor for chlorothalonil based on nylon 6,6 film deposited onto screen printed electrode (SPE) with electrochemical modulation of pH at the electrode/solution interface was studied for the first time. Differential pulse cathodic stripping voltammetry (DPCSV) was used to carry out the electrochemical and analytical studies. Experimental parameters such as accumulation potential, initial potential, accumulation time and pH of Britton-Robinson buffer have been optimized. Chlorothalonil gave optimum analytical signal in a medium of 0.04?M Britton-Robinson buffer at pH 6.0. A well-defined reduction peak was observed, at E_p= ?0.851 and ?0.938?V vs. Ag/AgCl (3.0?M KCl) for both bare SPE and modified SPE, respectively. The peak currents of modified SPE were significantly increased as compared to bare SPE. At the modified SPE, a linear relationship between the peak current and chlorothalonil concentration was obtained in the range from 0.1 to 2.8?×?10^?6?M with a detection limit of 1.53?×?10^?8?M (S/N=?3). The practical applicability of the newly developed method has been demonstrated on analyses of real water samples. The newly developed sensor shows good reproducibility with RSD of 3.92%. The nylon 6,6 modified SPE showed itself as promising sensor with good selectivity for chlorothalonil determination.     

废线路板稀贵金属含量分析及提取技术研究

废线路板的稀贵金属含量较高.论述了废线路板中金的提取方法,分为全部浸出工艺和选择性浸出工艺,并提出了稀贵金属的提取工艺流程.     

废弃线路板的破碎解离和气流分选研究

破碎和材料富集分离是废弃线路板资源化的关键技术。采用冲击破碎和气流分选技术对废线路板的机械分离过程进行了研究。结果表明使用锤式粉碎机破碎,线路板中主要金属在0.8mm以下基本解离,79.65%的金属集中分布在0.125～1.0mm粒级。气流分选得到品位较高的金属富集体,粒级0.125～1.0mm中的总金属回收率超过90%。     

Recycling of WEEE: characterization of spent printed circuit boards from mobile phones and computers

This paper presents a comparison between printed circuit boards from computers and mobile phones. Since printed circuits boards are becoming more complex and smaller, the amount of materials is constantly changing. The main objective of this work was to characterize spent printed circuit boards from computers and mobile phones applying mineral processing technique to separate the metal, ceramic, and polymer fractions. The processing was performed by comminution in a hammer mill, followed by particle size analysis, and by magnetic and electrostatic separation. Aqua regia leaching, loss-on-ignition and chemical analysis (inductively coupled plasma atomic emission spectroscopy - ICP-OES) were carried out to determine the composition of printed circuit boards and the metal rich fraction. The composition of the studied mobile phones printed circuit boards (PCB-MP) was 63 wt.% metals; 24 wt.% ceramics and 13 wt.% polymers; and of the printed circuit boards from studied personal computers (PCB-PC) was 45 wt.% metals; 27 wt.% polymers and ceramics 28 wt.% ceramics. The chemical analysis showed that copper concentration in printed circuit boards from personal computers was 20 wt.% and in printed circuit boards from mobile phones was 34.5 wt.%. According to the characteristics of each type of printed circuit board, the recovery of precious metals may be the main goal of the recycling process of printed circuit boards from personal computers and the recovery of copper should be the main goal of the recycling process of printed circuit boards from mobile phones. Hence, these printed circuit boards would not be mixed prior treatment. The results of this paper show that copper concentration is increasing in mobile phones and remaining constant in personal computers.     

灰色预测模型及分布活化能模型在废电路板热解中的应用

分别在管式炉反应器和热天平上对废电路板的热解行为进行实验研究。在管式炉反应器上考察了在同一升温速率（20 K/min）下不同热解终温 (400、500、600、700和800℃) 对废电路板热解产物产率的影响。在相关实验数据的基础上尝试用灰色理论及方法建立基于热解终温的废电路板热解灰色产率预测模型GM(1,1),预测结果与实验数据对比表明,该预测模型精度较高,能够较好地对不同热解终温下废电路板热解产物产率进行预测。此外,在热天平上获得的不同升温速率（10、15和20 K/min）下的热失重曲线表明,废电路板的失重速率峰随升温速率的提高逐渐向高温侧移动。采用分布活化能模型对废电路板热失重曲线进行动力学分析,获得废电路板热解活化能的变化曲线。计算结果表明,废电路板热解过程中活化能并不是单一数值,而是随失重率变化的一个函数。所得废电路板热解活化能值在140～250 kJ/mol范围内变化,当失重率在10%～60%之间,活化能值总体呈缓慢上升的趋势,但当失重率＞60%时,活化能值由155.4 kJ/mol迅速增加到244.4 kJ/mol。     

活性炭对细菌浸出线路板中金属铜的影响研究

研究了活性炭对细菌生长和浸出铜的效应影响。结果表明活性炭的添加对细菌的生长有一定的抑制作用,但这种作用随着添加量的增加而减弱。Fe3+对Cu浸出速率较快,活性炭对浸出速率有一定的促进作用,但效果不明显,且最终Cu的浸出率只达到87%。活性炭的添加增大了浸出体系中的生物量,加速了对Fe2+的氧化速率,从而保持溶液中较高的Fe3+浓度,可以提高铜的浸出速率。但这种促进作用需要较高浓度的活性炭添加量才比较明显。