前车突然切入时驾驶人应激生理特性研究

为研究前车突然切入对驾驶人生理负荷的影响,利用MP150生理监测系统对22名被试进行虚拟驾驶试验。采集记录前车突然切入时被试的生理参数。研究驾驶人心率增长率和心率变异性(HRV)指标与车速、应激距离之间的关系。结果表明:自车速度为100 km/h时,随着前车切入距离从55.6 m减小到27.8 m,被试的平均心率增长率从16.21%增大到23.27%,HRV参数低频(LF)值也呈现下降趋势。前车切入距离一定,随着自车车速从60 km/h增加到120 km/h,被试的平均心率增长率存在显著性差异,平均从13.05%上升到21.85%。差异性检验结果表明,前车切入距离和自车速度发生变化时驾驶人的生理负荷变化趋势一致,但自车速度因素对驾驶人生理负荷的影响程度高于切入距离因素。     

反应气氛对绿色合成纳米铁的组分及其活性的影响

成本低廉和无二次污染的"绿色"合成纳米材料是发展原位纳米环境修复技术的前沿研究课题之一.本文以绿茶提取液为还原剂和稳定剂进行"绿色"合成纳米铁,探讨在不同的气氛下"绿色"合成的纳米铁颗粒的主要成分,以期为调控合成纳米铁系材料提供基础研究.首先,利用扫描电子显微镜(SEM)、X射线能谱(EDS)、X射线光电子能谱分析(XPS)和傅里叶变换红外光谱(FTIR)等表征手段对不同反应气氛下合成的纳米铁颗粒的表面微观形貌、尺寸和价态结构进行分析.结果发现,在通入N2情况下,合成的纳米铁颗粒粒径为(84.7±11.5)nm,其主要成分以纳米零价铁为主;在通入空气情况下,合成的纳米铁粒径为(117.8±26.2)nm,其主要成分是纳米零价铁、氧化铁和四氧化三铁的混合物;通入O2时,合成的纳米铁粒径为(141.2±26.3)nm,其主要成分以四氧化三铁为主.其次,评价在不同气氛条件下合成纳米铁颗粒对去除亚甲基蓝(MB)的反应活性.结果表明,在反应温度313 K下降解初始浓度为50 mg·L-1的MB溶液,反应5 min时已达到平衡,通入N2合成的纳米铁降解MB,去除率高达98.7%,而通入O2合成的纳米铁反应效率低,对MB的去除率仅为65.3%.最后,从以上发现提出不同气氛下可以调控"绿色"合成的铁系纳米材料成分,从而导致不同的纳米修复环境中污染物的能力.     

德兴铜矿不同年份废石产酸规律研究

矿山选矿废石、尾矿在长期堆积过程中氧化产生的酸性废水会对环境造成严重危害.实验选取德兴铜矿1、5、10和20年废石进行产酸规律研究,静态评价结果显示,4种废石均有产酸潜势,且除1年废石以外均已产酸.为期9个月的动态评价结果表明,4个年份的废石pH均与电导率呈显著负相关,检出离子主要为氟化物、Cu2+、Zn2+、SO2-4、Fe3+.1年废石在整个实验进行中并未产酸,5、10年废石产酸稳定,20年废石产酸缓慢,可推断废石的产酸过程为:不产酸-高速产酸-稳定产酸-产酸速率下降.     

内循环厌氧反应器流动模型及反应过程模拟

为揭示内循环厌氧反应器放大过程中所出现的规律,本文对反应器中流动模型和反应过程进行了模拟研究,通过对主反应区的停留时间分布的实验研究,确定了主反应区流型可用一平推流与两个并联的全混流进行串联的三参数组合模型进行模拟.在实验范围内,平推流区所占的体积分数约为36%,两个全混流区所占的体积分数分别为53%和11%.结合厌氧反应动力学方程,应用组合模型模拟了实际反应器的状态,并和实验值进行了对比,发现反应器出口处CH_4体积流量最大误差为9.67%,在可允许的范围内.同时,模拟了基质初始COD和温度变化对反应器出口状态的影响.研究表明,与其它模型相比,组合模型计算简洁,同时又有较好的精度,能够满足反应器的设计需要.     

Heterogeneous oxidation of SO2 by O3-aged black carbon and its dithiothreitol oxidative potential

Ozone (O₃) is an important atmospheric oxidant. Black carbon (BC) particles released into the atmosphere undergo an aging process via O₃ oxidation. O₃-aged BC particles may change their uptake ability toward trace reducing gases such as SO₂ in the atmosphere, leading to different environmental and health effects. In this paper, the heterogeneous reaction process between O₃-aged BC and SO₂ was explored via in-situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS). Combined with ion chromatography (IC), DRIFTS was used to qualitatively and quantitatively analyze the sulfate product. The results showed that O₃-aged BC had stronger SO₂ oxidation ability than fresh BC, and the reactive species/sites generated on the surface had an important role in the oxidation of SO₂. Relative humidity or 254 nm UV (ultraviolet) light illumination enhanced the oxidation uptake of SO₂ on O₃-aged BC. The oxidation potentials of the BC particles were detected via dithiothreitol (DTT) assay. The DTT activity over BC was decreased in the process of SO₂ reduction, with the consumption of oxidative active sites.     

A thermal hazard risk evaluation of emulsion polymerisation and vinyl acetate monomers in the latex manufacturing process

Latex is extensively used in industrial products. However, completing some processes at scale leads to unacceptable levels of risk that need to be quantified and mitigated. Systemic risks must be eliminated wherever possible, and safety takes priority over efficiency and quality. To assess the process risks accurately, four raw materials were examined in this study: polyvinyl acetate (PVA), latex process-initiator-ammonium persulfate (APS) and hydrogen peroxide (H₂O₂), and vinyl acetate monomer (VAM). The physicochemical composition of the PVA latex process was determined via calorimeters, including differential scanning calorimetry (DSC) and vent sizing package 2 (VSP2). The calorimetry results showed that the protective colloid was a critical component in the polymerisation reaction. In addition, when adding initiators to the system, it is vital to observe the normal ratio of materials and keep the stirring system operating. The scenario system also simulated the effects of shutting down various inhibitory programs, including the build-up of free radicals that could result in a runaway reaction when the initiator was added in excess. On the other hand, the result of the risk matrix displayed as a medium level, indicating that although the probability of an accident is low, the resulting severity is at disaster level. As a result, this study provides process safety engineers with a reliable frame of reference for assessing the potential dangers in the PVA latex manufacturing process.     

蒙脱土原位生长MoS2复合材料光催化降解罗丹明B的机理研究

通过在Na⁺-MMT表面生长MoS₂来提高窄带隙半导体光生电子分离速率及稳定性.利用阳离子填充法及水热法成功制备了复合光催化剂Na⁺-MMT/MoS₂,并通过FT-IR、SEM、TEM、Raman、XRD、TG、XPS、UV-DRS和ESR等表征进一步证明了材料的成功负载及光、电化学性能. 同时,以有机染料罗丹明B为待降解染料来评价光催化剂的催化性能,发现其在80 min可有效降解罗丹明B,降解率达96%.经过5次循环使用后,Na⁺-MMT/MoS₂复合光催化剂仍具有较好的光催化性能.因此,利用MMT的表面电负性及稳定的片层结构负载MoS₂,可形成光生电子迁移通道进一步提高电荷迁移速率及光催化剂的稳定性.本研究可为黏土材料调控窄带隙半导体制备环境友好型光催化剂提供新思路.     

火工品温湿度加速老化模型和算法研究

目的 研究对火工品适用的温湿度加速模型,以及加速系数计算程序,获取准确的温湿度加速系数外推公式.方法 通过分析国内外使用的各种双因素加速模型的适用性,确定火工品适用的温湿度加速模型,采用免费自由的开源统计分析软件——R软件,对通过加速试验获取的某点火头2种温湿度加速条件下的试验数据,进行单组数据拟合和多组数据拟合两种温湿度加速老化算法的开发,并且对2种算法、3种寿命分布下寿命外推的准确性进行对比分析.结果 确定了Peck模型适合用于火工品的温湿度加速模型,获取了某电点火头对应的温湿度加速系数和湿度项反应速率常数.结论 基于多组数据拟合的温湿度加速老化算法,比基于单组数据拟合的温湿度加速老化算法对试验数据的兼容性好.3种寿命分布中,Weibull分布的加速系数计算结果最保守.     

纳米零价铁在应用中存在的问题及提高反应活性的方法

纳米零价铁对多种污染物质均有较好的去除效果,在污染的水体、土壤及底泥中被广泛研究与应用。前人对纳米零价铁的制备、在污染治理各方面的应用、作用的机理等方面进行了较为详细的总结,针对纳米零价铁在应用中存在的问题虽有提及,但少有人集中进行整理。本文主要针对纳米零价铁在环境治理方面存在的问题进行论述并对提高其反应活性的常用方法进行了总结,以期为纳米零价铁实际应用领域的深入研究提供借鉴并拓展新的思路。     

H2O2 treatment boosts activity of NiFe layered double hydroxide for electro-catalytic oxidation of urea

Urea oxidation reaction (UOR) provides a method for hydrogen production besides wastewater treatment, but the current limited catalytic activity has prevented the application. Herein, we develop a novel H₂O₂ treatment strategy for tailoring the surface oxygen ligand of NiFe-layered double hydroxides (NiFe-LDH). The sample after H₂O₂ treatment (NiFeO-LDH) shows significant enhancement on UOR efficiency, with the potential of 1.37 V (RHE) to reach a current density of 10 mA/cm². The boost is attributed to the richness adsorption O ligand on NiFeO-LDH as revealed by XPS and Raman analysis. DFT calculation indicates formation of two possible types of oxygen ligands: adsorbed oxygen on the surface and exposed from hydroxyl group, lowered the desorption energy of CO₂ product, which lead to the lowered onset potential. This strategy is further extended to NiFe-LDH nano sheet on Ni foam to reach a higher current density of 440 mA/cm² of UOR at 1.8 V (RHE). The facile surface O ligand manipulation is also expected to give chance to many other electro-catalytic oxidations.