A pilot-scale study of cryolite precipitation from high fluoride-containing wastewater in a reaction-separation integrated reactor

Fluoride removal by traditional precipitation generates huge amounts of a water-rich sludge with low quality, which has no commercial or industrial value. The present study evaluated the feasibility of recovering fluoride as low water content cryolite from industrial fluoride-containing wastewater. A novel pilot-scale reaction-separation integrated reactor was designed. The results showed that the seed retention time in the reactor was prolonged to strengthen the induced crystallization process. The particle size of cryolite increased with increasing seed retention time, which decreased the water content. The recovery rate of cryolite was above 75% under an influent fluoride concentration of 3500 mg/L, a reaction temperature of 50℃, and an influent flow of 40 L/hr. The cryolite products that precipitated from the reactor were small in volume, large in particle size, low in water content, high in crystal purity, and recyclable.     

磁性多孔陶粒生物膜反应器处理焦化废水的试验研究

以磁性材料为原料,经过特定的工艺处理,对多孔陶瓷进行磁化改性获得磁性多孔载体,并将该载体应用于生物膜反应器中进行焦化废水处理试验。对不同类型的多孔陶粒载体进行对比试验,结果表明:磁性载体生物膜反应器对COD、NH3-N的去除率比普通活性污泥法高出25%³0%,比非载体生物膜反应器高出15%30%,比非载体生物膜反应器高出15%²0%左右。反应器的曝气量为1.5 L/h,曝气时间为10 h/d,温度为2520%左右。反应器的曝气量为1.5 L/h,曝气时间为10 h/d,温度为25³0℃。焦化废水经磁性载体生物膜反应器处理后,上清液中COD,NH3-N的去除率均在90%左右。出水浓度达到国家工业废水排放二级标准(GB18918-2002)。     

ABR反应器中COD/SO_4~(2-)值和硫酸盐负荷对SO_4~(2-)去除影响

利用厌氧折流板反应器,分别考察了反应器启动,及不同COD/SO42-比值和硫酸盐负荷对模拟废水中SO42-去除的影响。实验在(32±0.1)℃,pH为6.0⁶.5的条件下连续运行。结果表明:ABR经过约90 d的启动驯化阶段后,进水硫酸盐及COD浓度分别为1 500 mg/L和3 000 mg/L,水力停留时间为12 h条件下,硫酸盐去除率达到了92%。固定COD/SO42-比值为2.5时,随着进水SO42-浓度的增加(1 5006.5的条件下连续运行。结果表明:ABR经过约90 d的启动驯化阶段后,进水硫酸盐及COD浓度分别为1 500 mg/L和3 000 mg/L,水力停留时间为12 h条件下,硫酸盐去除率达到了92%。固定COD/SO42-比值为2.5时,随着进水SO42-浓度的增加(1 500³ 500 mg/L),SO42-去除率逐渐下降,最低为60%,相反SO42-去除速率随着硫酸盐浓度的增加而增加,最大为7.98 kg(/m3.d);维持恒定的硫酸盐浓度(1 500 mg/L),逐渐缩短水力停留时间以提高反应器中硫酸盐负荷,SO42-去除率呈现先上升后下降的复杂变化趋势,当水力停留时间为6 h时,SO42-去除率达到最大;随着COD/SO42-比值的提高,硫酸盐去除能力增强,且反应体系对硫酸盐负荷的耐受能力也逐渐增强。     

涡流澄清池与网格澄清池处理的对比试验研究

针对传统水力循环澄清池运行中所遇到的混凝效率低、出水水质差、抗冲击负荷能力弱等瓶颈问题,该试验通过对涡流澄清池与网格澄清池的启动、除浊效果、产水能力、抗冲击负荷能力进行平行对比试验,研究了涡流澄清池实际运行效果,确定了涡流澄清池的最佳运行工况及相关设计参数,为微涡流澄清技术在水厂改造、净水装置研发及其他工程应用提供设计参数支持和推广应用依据。     

钢渣湿法捕获CO_2反应机制研究

以炼钢过程中排放的固体废弃物钢渣为碳捕获剂,进行了钢渣湿法捕获烟气CO2工艺的实验研究。通过分析钢渣的组成成份及反应机理,研究液固比、反应温度、反应时间、pH值及反应产物等主要参数对钢渣湿法碳捕获状况的影响。实验证明,通过合理的设计和适当的操作,可使钢渣湿法碳捕获效率达60%以上,具有一定的应用价值。     

关于不锈钢酸洗废水处理的技术分析

随着社会经济的快速发展,不锈钢酸洗废水处理技术成为了当前的一项重要技术参数。本文旨在分析当前不锈钢酸洗废水的相关处理技术,从多种技术综合的应用出发,围绕当前工业发展的实际需要,多角度的分析不锈钢酸洗废水的技术,实现整体技术的全面运用。     

辽河流域水环境压力及污染治理模式研究

系统分析了辽河流域近十年社会经济和水污染物排放之间的关系,基于污染物排放强度和人均GDP指标,建立辽河流域COD和氨氮环境学习曲线;结合情景分析法预测在现有治污水平下,辽河流域未来水污染物排放趋势及水环境压力。结果表明,辽河流域水环境压力巨大。根据辽河流域污染治理中存在的实际问题,提出新时期的污染治理模式。     

Application of CGP-cross route process for microstructure refinement and mechanical properties improvement in steel sheets

A modified method of severe plastic deformation (SPD) entitled constrained groove pressing-cross route (CGP-CR) was introduced for imposing a high magnitude of equivalent strain of about 2.32 per pass on the sheet form samples. The major benefit of this improved route compared to previous common route was the more homogeneity of strain in the rolling (RD) and transverse (TD) directions of sheets. In this study, low carbon steel samples were used for examination of evolutions in microstructure and mechanical properties during SPD via CGP-CR process. Mechanical properties improvement were measured by tensile and macro hardness tests. The results indicate that CGP-CR process can effectively improve tensile strength; and also, yield stress and hardness of as-received low carbon steel samples were improved up to about 100% after two deformation passes. Also, high magnitude of inhomogeneity can be observed in hardness distribution through first pass of the process which diminishes in the subsequent passes. Microstructural evolutions during process were monitored by optical microscopy observations and X-ray diffraction analysis. The results demonstrate that initial ferritic microstructure with grain size of about 30 μm was refined to a 225 nm cell structure after two passes of CGP-CR process.     

反应器引压端法兰焊接阀门断裂原因分析

通过对Z41H-160型阀体端法兰断裂件的宏观检查、化学成分分析、金相分析、断口形貌观察、EDS能谱分析和维氏硬度测试等研究,表明阀体热处理不当致使硬度超高,阀门结构不合理导致硫化物应力腐蚀是阀体断裂的主要原因。