Effect of flame propagation regime on pressure evolution of nano and micron PMMA dust explosions

Experiments using an open space dust explosion apparatus and a standard 20 L explosion apparatus on nano and micron polymethyl methacrylate dust explosions were conducted to reveal the differences in flame and pressure evolutions. Then the effect of combustion and flame propagation regimes on the explosion overpressure characteristics was discussed. The results showed that the flame propagation behavior, flame temperature distribution and ion current distribution all demonstrated the different flame structures for nano and micron dust explosions. The combustion and flame propagation of 100 nm and 30 μm PMMA dust clouds were mainly controlled by the heat transfer efficiency between the particles and external heat sources. Compared with the cluster diffusion dominant combustion of 30 μm dust flame, the premixed-gas dominant combustion of 100 nm dust flame determined a quicker pyrolysis and combustion reaction rate, a faster flame propagation velocity, a stronger combustion reaction intensity, a quicker heat release rate and a higher amount of released reaction heat, which resulted in an earlier pressure rise, a larger maximum overpressure and a higher explosion hazard class. The complex combustion and propagation regime of agglomerated particles strongly influenced the nano flame propagation and explosion pressure evolution characteristics, and limited the maximum overpressure.     

SCR脱硝装置关键断面的流场试验及系统优化

选择性催化还原脱硝是NO X治理最佳技术,其脱硝效率、氨逃逸率与关键断面的流场状况密切相关。以某300 MW机组SCR脱硝装置为对象,在锅炉冷态通风条件下,对SCR反应器入口导流板出口、上层及中层催化剂床层上方0.5 m处3个断面进行流场测试,结果表明:沿烟气流动方向,3个断面A/B侧相对偏差系数分别为0.33/0.40、0.27/0.29、0.16/0.18,均呈现甲乙侧均匀,而前后墙差异大的特点。由于格栅、床层的整流作用,后续烟气流动的均匀性不断改善。通过建立全尺寸三维计算模型,CFD数值模拟优化结果显示,对非等距布置后墙的18个整流格栅逐渐加高,可使上层催化剂床层上方0.5 m处速度偏差从27.0%降到12.2%。     

多元可燃性气体爆炸压力与中间产物发射光谱特性的耦合研究

工业生产中爆炸事故往往是由多元可燃气体与空气混合后遇到明火而引起的,为研究乙烷（C₂H₆）、乙烯（C₂H₄）、一氧化碳（CO）、氢气（H₂）对甲烷爆炸特性的影响,选取多组分可燃气体甲烷爆炸压力特性和自由基发射光谱的影响进行研究,利用陕西省工业过程安全与应急救援工程技术研究中心重点实验室搭建的多功能球形气体/粉尘爆炸实验装置和单色仪进行爆炸实验测试,同步采集时间—压力曲线、中间产物（OH,CH₂O）的发射光谱信号,考察多组分可燃气体浓度对甲烷爆炸压力特性和中间产物的影响。结果表明:在富氧状态下,多组分可燃气体加剧了甲烷—空气混合体系的爆炸剧烈程度,随着体系中氧气含量的减少、由富氧状态变为贫氧状态、促进作用逐渐减弱转变为阻尼作用,爆炸压力特性与中间产物发射光谱参数的影响规律基本保持一致,均呈高度正相关;多元混合体系爆炸剧烈程度越大,自由基发射光谱达到峰值的速度越快,自由基更早、更快的积累是加剧爆炸程度的原因之一。     

玻璃纤维-砂浆管试件动态拉伸破坏特性试验研究

为了探究动载作用下GFRP（玻璃纤维）-砂浆管的动态拉伸破坏特性,采用分离式SHPB试验装置对2种空心率的水泥砂浆管和GFRP-砂浆管进行动态拉伸试验。结果表明:空心率越小、冲击气压和壁厚越大,试件峰值抗拉强度越大;GFRP-砂浆管的峰值抗拉强度随GFRP管壁厚的增大而不断增大,在空心率为0.292时,峰值抗拉强度随GFRP管壁厚增大呈对数函数递增,而在空心率0.187时,峰值抗拉强度随GFRP管壁厚增大呈指数函数递增;无GFRP管时水泥砂浆管呈对称四块破碎,GFRP-砂浆管在0.5~0.7 MPa冲击气压下仅有细小裂纹产生,在0.8 MPa冲击气压下,与入射杆接触部分产生“楔形”破坏,但总体保持为管状、破坏程度仍低于水泥砂浆管,表明GFRP管对水泥砂浆管具有较好的保护作用,可有效提高其动态抗拉强度。     

Mutual effects between dynamic leakage behavior and the pressure/temperature in a LNG tank with external heat fluxes

The objective of this work is to investigate and model the mutual effects between the dynamic pressure/temperature in the LNG tank and the leakage behavior with external heat fluxes. The results suggest that the pressure and temperature in tank during leakage change with the comparison results between the heat flux consumed in liquid boil-off and the external heat flux supplied. At the liquid leakage stage, when the external heat flux is not very high, the pressure in tank tends to increase significantly, even results in tank explosion. It increases more and more heavily with higher and higher external heat fluxes. At the vapor leakage stage, large amount of vapor spray out, which results in a high generation rate of vapor by the liquid boil-off. The pressure in tank normally decreases to be low, which is unfavorable for the LNG tank explosion. Therefore, at this vapor leakage stage, blocking the leakage hole as soon as possible is not always a right choice for fire fighters. Finally, it is suggested that reducing the heat flux into the tank, either at the liquid leakage stage or in vapor one, is key to the tank safety.     

高压水射流卸压防治复合动力灾害机理及应用

为研究高压水射流卸压防治复合动力灾害的可行性,以余吾煤业高瓦斯矿井东翼采区内首采N2105工作面工程地质条件为背景,通过现场调研、理论分析、数值模拟和工业性试验等方法,对N2105进风平巷两帮采取高压水射流卸压防治效果进行了研究。结果表明:对巷帮煤体采取高压水射流卸压技术,煤体在高压水射流的冲击力和扰动应力波共同作用下瞬间发生破坏;巷帮侧支承应力分布曲线由原有的“单高峰值”转变为“内低外高双峰值”,受以上支承应力变化的影响,底板煤岩体内难以形成范围较大且连续的塑性应力状态区;现场电磁辐射和矿压监测结果表明高压水射流技术对煤层卸压增透效果显著,降低了巷道发生复合动力灾害的可能性。研究结果可为同类矿井复合动力灾害的防治提供参考和借鉴。     

不饱和聚酯树脂在储罐内衬改造中的静电危害分析

为分析不饱和聚酯树脂在内衬改造应用中存在的引燃风险,阐述加油站埋地罐内衬改造工艺,测试不饱和聚酯树脂固化放热特性、与玻璃钢摩擦的滚刷及装树脂绝缘桶的表面静电电位。结果表明:不饱和聚酯树脂与固化剂混合后的放热不足以引起树脂自燃;滚刷、树脂与绝缘桶间摩擦可导致桶表面静电位超过7 kV,带电绝缘体表面与金属凸出物间存在静电放电现象、甚至引起挥发苯乙烯局部闪燃风险。油罐内衬改造时需强化通风以及增加静电防护措施,避免静电放电引起罐内燃爆事故。     

常温下IC反应器启动过程中的颗粒污泥性能研究

在常温下用自配葡萄糖废水启动IC反应器,研究了厌氧颗粒污泥的形成过程和特性。IC反应器进水浓度为3 000 mg COD/L,水温为14.5～26℃,25 d内形成了颗粒污泥。结果表明,随着运行时间和容积负荷的增加,颗粒污泥粒径逐渐增大。反应器启动完成后,反应器中2 mm的颗粒污泥增加到6.6%,0.3 mm的颗粒从57.7%减少到39.4%;VSS浓度从24.7 g/L上升到48.2 g/L;VSS/SS从34.4%增加到72.8%。颗粒污泥的沉降速度与颗粒粒径成正比,0.3～3 mm的颗粒污泥的沉降速度介于34.05～109.75 m/h之间,具有良好的沉降性能。初始接种污泥几乎没有产甲烷活性,与第30 d的初期颗粒污泥相比,成熟的颗粒污泥的产甲烷活性提高了46.7%。     

垂直厌氧折流板反应器处理树脂废水的中试研究

介绍了采用垂直厌氧折流板反应器(VABR)处理离子交换树脂生产废水的中试实验装置以及实验研究过程,并着重分析了COD容积负荷和盐分对COD的去除率及出水VFA的影响,并确定了该废水的厌氧产沼气率。研究结果表明,在中温(37±1℃)环境下,容积负荷在9 kg COD/(m3.d)左右时,HRT为24 h的条件下,VABR对COD的平均去除率保持在70%左右,平均每去除1 kg COD约产生沼气0.44 m3,且运行稳定。