ABR反应器的碱度变化及调控研究

研究了折流厌氧反应器(ABR)运行中碱度的变化情况及其与ABR各格室中VFA、pH和COD变化之间的关系.结果表明,碱度沿程变化与反应器的VFA浓度变化密切相关,碱度和pH值的最低点出现在VFA浓度最高点.碱度条件是通过pH值影响系统的运行.ABR沿程碱度和pH值变化都存在一个先降低后上升的过程.碱度控制一般以保证ABR沿程最低pH值不低于6.0为准,6.5以上为佳.进水碱度的下限与反应器的进水浓度密切相关.在低负荷COD条件下[3.7 kg/(m³·d)],保持ABR运行良好的最低碱度为800 mg/L.     

超声对污泥流变性及絮凝脱水性的影响

采用旋转粘度法研究了活性污泥体系的流变特性,考察和比较了超声处理前后污泥粘度及过滤比阻的变化,并就超声处理污泥的絮凝脱水性能进行了相关测试和分析.结果表明,随剪切速率的增大,污泥表观粘度降低,流动性增大,表现出流体变稀;污泥的流变特性反映出其胶状网络结构具有相对稳定性,污泥对水的结合能力强,因此,其过滤比阻高、脱水性能差;在固定频率25 kHz条件下,低声能密度(0.10～0.15W·mL-1)、短时间(2～3 min)超声处理可有效降低污泥表观粘度及过滤比阻;在絮凝剂(PDMDAAC)投量为污泥干固体质量(TS的)0.5%时,超声处理污泥的过滤比阻与滤饼含水率可分别降低至最小值0.18×109s2·g-1和65.7%.实验结果表明,将超声与絮凝剂结合用于污泥调理是可行的.     

Performance of a novel vertical-flow settler: a comparative study

By increasing particle concentration and G value （root-mean-square velocity gradient） to enhance flocculation, a novel vertical-flow settler was designed to increase sedimentation effectiveness, and to simultaneously improve operational stabilization. Due to the gradual decrease in upward flow-rate of raw water, a floes blanket would form and suspend in the middle section of the settler, not at the bottom as in a conventional clarifier. Enough large floes, resulted from flocculation or fltration, would continuously settle out of the floes blanket, and simultaneously, the floes in raw water or those forming above the blanket would ceaselessly enter the floes blanket. As a result, the floes concentration in the blanket could keep a dynamic balance. The hydrodynamic shear in the blanket was improved by flow separation, which was induced by the abrupt change in flow channel. Due to the floes blanket and improved hydrodynamic shear, flocculation would be enhanced, which was helpful for removing fine particles in raw water. A comparative study showed that the novel vertical-flow settler had a much better performance in the removal of the particles in raw water than a conventional one, when they treated kaolin suspensions of different concentrations （500, 100 and 50 mg/L, respectively） coagulated by polyaluminum chloride（PAC1） at the up-flow rates of 1 and 2 mm/s, respectively.     

基于疲劳累积破坏机制的储罐结构动力可靠度分析

针对随机风载荷作用下储罐结构动力可靠性问题,以300 m3的中小型立式低温储罐为研究对象,利用AR模型进行数值模拟得到风载荷的脉动风速时程与脉动功率谱密度函数。采用ANSYS建立储罐三维有限元模型,并对储罐进行动力学分析,计算出储罐结构的随机响应,进而求出随机风载荷作用下储罐结构动力可靠性所需全部数字特征,最后利用疲劳累积损伤机制计算得到储罐的动力可靠度。结果表明:假设结构强度不随时间退化,前5 a动力可靠度基本保持不变,随着使用年限的延长,动力可靠度下降速度明显增大。研究方法可为储罐的动力可靠性及寿命预测提供一定的理论依据。     

Study on the dynamic response of polyurea coated steel tank subjected to blast loadings

Steel tanks are widely used in the storage of various chemical liquids, and the blast resistance of the tanks is very important because of the explosiveness of these liquids. To explore a feasible method to improve the blast resistance of steel tanks, the effect of polyurea coating on the blast resistance of steel storage tank is investigated in this paper. The responses of monolithic steel tanks and polyurea coated tanks under blast loads are studied by field blast experiments using TNT explosive, and the results shows that the polyurea layers are effective in reducing the maximum and residual displacements of the tank. Numerical simulations are performed and validated, and the deformation process and stress and strain distribution of the tanks are analyzed accordingly. The increase on the bending moment of the plastic hinge lines of the tanks and the increase of the area density of the cylindrical shell induced by the polyurea layers are believed to be the two main factors contributing to the displacement reduction effect of polyurea in this paper. The validated numerical model is used to study the influence of polyurea layer's thickness on the deflection of the tank, and a nearly inversely proportional relationship between the thickness and the maximum displacement is found. Three deformation modes of the tanks are identified when subjected to blast load with varying intensity and it is found that the displacement reduction effect of polyurea varies in different deformation modes.     

pH对煤泥水絮凝沉降的影响

选择聚合氯化铝(PAC)/阴离子型聚丙烯酰胺(PHP)、氯化钙(CaCl2)/非离子型聚丙烯酰胺(NPAM)组合与NPAM、PHP、两性离子型聚丙烯酰胺(ZPAM)作为絮凝剂,在对道清选煤厂水采筛下原生煤泥和浮选尾矿的煤泥水进行组合药剂絮凝实验的基础上,考察了pH对煤泥水絮凝沉降的影响。实验结果表明,在不同的pH下,煤泥水的絮凝效果不同:在酸性条件下,宜单独使用有机高分子絮凝剂;在中性至碱性条件下,无机凝聚剂和有机絮凝剂联合使用效果较好。     

混凝-Fenton试剂氧化工艺处理机械厂洗涤废水

对某厂机械洗涤废水,采用混凝-Fenton试剂进行处理。结果表明,用聚铝（w（PAC）=5%）对废水进行絮凝沉淀,PAC最佳投加量为1.5 mL/L（废水）,絮凝后的COD去除率为29.6%;芬顿试剂最佳操作条件为：n（H2O2）∶n（Fe2＋）=5∶1,m（H2O2）∶m（COD）=2.5∶1,废水pH=5,温度为30℃,反应时间为2 h,经氧化后,COD的去除率为78.5%;经过混凝沉淀-芬顿氧化处理,COD的总去除率为84.9%,去除效果良好。     

连续流反应器中培养好氧颗粒污泥的运行效能研究

在连续流完全混合反应器(CSTR)中,采用不同进水方式,以乙酸钠作为碳源配制的人工配水作为原水,对好氧颗粒污泥的运行效能进行了试验研究。研究表明,采用不同进水方式运行的2个反应器在颗粒污泥出现后,运行效能差别不大;好氧颗粒污泥反应器运行高效稳定,在水力停留时间为1.5h、COD容积负荷为1.0kg/(m3·d)的条件下,对COD、TP、NH4+-N和TN的去除率分别为90%、85%、95%和60%,并具有明显的脱氮除磷效果;反应器中存在同步硝化反硝化现象。     

罐底含油泥热解动力学参数计算方法的优选

在化学反应设计中反应动力学是较重要的因素。为得到更合理的污泥热解动力学参数计算方法,利用热重分析仪,在氮气气氛下对罐底含油污泥的热解特性进行研究。根据热重实验数据,分别采用Coats-Redfern法、Kissinger法、FWO法和Popescu法计算污泥热解动力学参数,并获取罐底泥热解制油的主要阶段(第2阶段)的反应活化能E、频率因子A并分析各种方法反应机理。通过对比不同计算方法得到动力学参数及拟合曲线与实验曲线的相关性,确定了最佳罐底含油污泥热解动力学参数计算方法。研究表明,Popescu法得到罐底泥的热解过程符合Jander方程,活化能E为101.43 kJ/mol,与FWO法得到的91.20 kJ/mol相近,且预测曲线与实验曲线有较好的相关性(0.9816),说明Popescu法计算罐底泥热解动力学参数更合适。     

基于底泥再悬浮试验的太湖水质模拟

为探索浅水湖泊水动力扰动作用对底泥再悬浮影响的规律,在室内矩形水槽内模拟了各种水动力条件下太湖底泥的起动规律,得到了太湖底泥在3种不同起动标准下的起动流速,通过考察上覆水中悬浮物浓度的变化,建立了底泥沉积物再悬浮通量与水体流速的定量化关系。结果表明:太湖底泥在个别动、少量动、普遍动3种标准下的起动流速分别为15、30和40 cm/s,且底泥沉积物再悬浮通量与流速呈现线性正相关关系,再悬浮通量随流速增大而增大,且相关性较好。将该试验结果应用于太湖的水量水质数学模型中,并和太湖实测资料进行了对比,取得了比较满意的效果。该模拟装置能够在室内可控条件下较好地反映太湖沉积物再悬浮特征,对太湖的富营养化治理具有重要意义。