絮凝#x02014;微波辐射#x02014;Fenton试剂氧化法深度处理焦化废水

用絮凝#x02014;微波辐射#x02014;Fenton试剂氧化法深度处理焦化废水,研究了微波辐射时间、微波功率、FeSO₄加入量、H₂O₂加入量和废水pH对废水处理效果的影响。实验结果表明：在聚合氯化铝加入量为350mg/L、聚丙烯酰胺加入量为12mg/L、废水pH=5、FeSO₄加入量为250mg/L、H₂O₂总加入量为1400mg/L、H₂O₂分3次投加、微波功率为400W、微波辐射时间为60min的条件下,处理后出水的浊度、色度和COD去除率分别为98.59%,97.62%,86.21%。处理后出水澄清透明,COD为50.34mg/L,满足GB50050#x02014;2007《工业循环冷却水处理设计规范》的要求。     

UASB-SBR-絮凝工艺处理地沟油制生物柴油废水

采用UASB-SBR-絮凝工艺处理地沟油制生物柴油废水,考察了各个阶段的废水处理效果。实验结果表明：UASB稳定运行阶段进水COD约为15000mg/L时,COD去除率约为87%,出水COD在2500mg/L以下,出水挥发性脂肪酸（VFA）浓度为4~6mmol/L,最佳容积负荷为15.0kg/（m3·d）;采用SBR处理UASB出水,当容积负荷为1.5kg/（m3·d）时,出水COD在200mg/L以下,COD去除率在83%以上,ρ（NH₃-N）在5mg/L以下,TP约为25mg/L。向SBR出水中加入质量分数为5%的聚合氯化铝进行化学除磷,加入量为5mL/L,处理后废水TP为4~6mg/L。处理后废水的COD,ρ（NH₃-N）,TP均达到CJ343-2010《污水排入城市下水道水质标准》的A类要求。     

Comprehensive Environmental Investigation at Former Industrial/Petroleum Underground Storage Tank Sites in Long Beach,CA: A Forensic Perspective

Two industrial sites were investigated based on years of available hydrogeologic information and monitoring data for soil and groundwater. Collected data were forensically evaluated using age-dating and fingerprinting methods. The previous business uses of the project sites were as a gas station, laundry/dry-cleaning service, and car wash with petroleum underground storage tanks (USTs). As a result, these sites were exposed to a number of toxic contaminants at relatively high concentrations. Source control was necessary for successful remediation and the ultimate removal of the remaining compounds from these industrial sites. Although contaminated soil around the source was excavated during the remedial action and the high concentrations of contaminants were reduced, typical groundwater contaminants such as petroleum hydrocarbons as gasoline (TPH-G), benzene, toluene, ethylbenzene, xylenes (BTEX), and oxygenates including methyl tert-butyl ether (MTBE), diisopropyl ether (DIPE), ethyl tert-butyl ether (ETBE), tert-amyl methyl ether (TAME), and tert-butyl alcohol (TBA) were persistently found at the studied sites around the source points. The plume and concentration of contaminants had changed their shapes and strength for all monitoring periods. Thus, additional source control seems to be a requirement for the complete removal of source contamination, which must be ascertained with groundwater and soil monitoring on a regular time base. For the study sites, monitored natural attenuation was relatively feasible for the long-term plan; however, it did not offer a perfect remediation solution for an ultimate goal because of residual toxic compounds that might have affected the surrounding residential areas at higher concentrations than their health limits. Therefore, as a remediation strategy, the combination of clean-up technology and natural attenuation with monitoring activities are more highly recommended than either clean-up or natural attenuation used separately.     

罐底含油泥热解动力学参数计算方法的优选

在化学反应设计中反应动力学是较重要的因素。为得到更合理的污泥热解动力学参数计算方法,利用热重分析仪,在氮气气氛下对罐底含油污泥的热解特性进行研究。根据热重实验数据,分别采用Coats-Redfern法、Kissinger法、FWO法和Popescu法计算污泥热解动力学参数,并获取罐底泥热解制油的主要阶段(第2阶段)的反应活化能E、频率因子A并分析各种方法反应机理。通过对比不同计算方法得到动力学参数及拟合曲线与实验曲线的相关性,确定了最佳罐底含油污泥热解动力学参数计算方法。研究表明,Popescu法得到罐底泥的热解过程符合Jander方程,活化能E为101.43 kJ/mol,与FWO法得到的91.20 kJ/mol相近,且预测曲线与实验曲线有较好的相关性(0.9816),说明Popescu法计算罐底泥热解动力学参数更合适。     

阿海水电站新源沟砂石加工废水处理工艺浅谈

新源沟砂石加工系统生产废水SS浓度高,采用水力旋流/加药絮凝/多级沉淀工艺处理,运行结果表明,处理出水水质满足《污水综合排放标准》（GB8978-1996）一级标准中的给定限值70mg/L,达标出水全部回用。     

稠油污水回用锅炉处理工艺的应用

新疆油田公司稠油污水处理普遍采用成熟的离子调整旋流反应水处理技术,污水处理后达到回用锅炉水质标准SY/T 0097-2000《稠油油田采出水用于蒸汽发生器给水处理设计规范》,供给油田专用高压注汽锅炉用水。采用相同技术建成的采油一厂稠油处理站污水回用锅炉处理工艺投用后,处理后污水回用锅炉,减少了含油污水的外排,充分利用了稠油污水的热能,取得了良好的经济和社会效益。     

常温条件下2种厌氧折流板反应器处理淀粉废水的启动实验

为了研究厌氧折流板反应器在常温下的启动情况,在22.5～30.2℃条件下,对不加填料的5隔室厌氧折流板反应器和加填料的4隔室复合式厌氧折流板反应器同步进行了启动实验。实验用水为高浓度淀粉废水,两反应器采用相同的启动策略,即梯度增加进水COD浓度与降低水力停留时间相结合的方式。两反应器有效容积均为47.8 L,启动初始负荷为0.6 kg COD/(m3.d),逐渐增加到10 kg COD/(m3.d)。实验表明,经过6个阶段87 d的运行,反应器启动完成,并成功培养出颗粒污泥,两反应器对COD的去除率都能达到85%以上。在启动过程中两反应器对COD的去除效率相近。     

曝气浸没固定生物膜反应器处理化粪池出水

研究了以丝瓜络作为生物膜载体的曝气浸没固定生物膜反应器在处理化粪池出水时的可行性以及运行性能。结果表明,丝瓜络生物膜反应器可以在2周内成功启动;水力停留时间(HRT)对COD和氨氮的去除效果有显著影响,在水力停留时间为4 h的条件下,系统对COD和氨氮的去除率分别达到了78.5%和96.4%。另外,系统有较强抗有机污染物冲击负荷的能力,当COD和氨氮的进水浓度分别为59.3 mg/L和15.9 mg/L时,系统对有机污染物的去除效果较佳,去除率分别达到了80.0%和98.9%。     

二级絮凝-活性炭处理实验室无机废水的效果

采用两级絮凝-活性炭吸附法处理实验室无机废水,研究了该方法对重金属、硫化物、挥发酚、苯胺和浊度等的处理效果。结果表明,在絮凝温度、搅拌、曝气及污水pH值调节范围一定的情况下,硫酸亚铁(FeSO4.7H2O)与聚合氯化铝(PAC)结合的二级絮凝方法能有效地降低污水中的重金属和硫化物等污染物。二级絮凝处理中,使用聚合氯化铝(PAC)对一级絮凝中去除效果不好的Cr6+的去除效果显著,去除率达到90%以上;活性炭对苯胺和硫化物的去除效果最佳,去除率都在90%以上。同时,该方法还有效降低了废水的浊度和色度。因此,是一种快速、低成本和工艺简单的处理实验室废水的有效途径。     

连续流反应器中培养好氧颗粒污泥的运行效能研究

在连续流完全混合反应器(CSTR)中,采用不同进水方式,以乙酸钠作为碳源配制的人工配水作为原水,对好氧颗粒污泥的运行效能进行了试验研究。研究表明,采用不同进水方式运行的2个反应器在颗粒污泥出现后,运行效能差别不大;好氧颗粒污泥反应器运行高效稳定,在水力停留时间为1.5h、COD容积负荷为1.0kg/(m3·d)的条件下,对COD、TP、NH4+-N和TN的去除率分别为90%、85%、95%和60%,并具有明显的脱氮除磷效果;反应器中存在同步硝化反硝化现象。