针铁矿对Pb~(2+)的吸附特征及影响因素研究

通过恒温振荡平衡法研究了Pb~(2+)在针铁矿上的等温吸附和吸附动力学特征,探讨了吸附的影响因素.结果表明:(1)随Pb~(2+)平衡浓度和pH的增大,针铁矿对Pb~(2+)的吸附量逐渐增大.(2)针铁矿对Pb~(2+)的等温吸附可用Freundlich和Langmuir方程较好地拟合.(3)在相同温度和pH下,随离子强度的提高,针铁矿对Pb~(2+)的吸附量增大.(4)在相同离子强度和pH下,针铁矿对Pb~(2+)的吸附量总体随温度升高而增大.针铁矿对Pb~(2+)的吸附是自发进行的吸热反应.(5)针铁矿吸附Pb~(2+)的过程可分为初始的快吸附和随后的慢吸附2个阶段.pH影响吸附反应快慢,随pH增大吸附速率增大;随着pH的增大,达到平衡吸附的时间缩短.吸附动力学方程用Elovich方程拟合最佳.     

生活垃圾加载介质层填埋法对初期渗滤液污染抑制效果研究

以传统卫生填埋柱R2为对照,通过往生物反应器填埋柱R1内加载可渗透反应介质层1和2进行模拟试验,主要探讨了填埋柱R1垃圾渗滤液COD、总氮、氨氮及总磷的变化趋势,探索一种新型的加载介质层垃圾填埋处理方法。试验结果表明,填埋20周后, R1柱COD浓度基本维持在40 000～45 000 mg/L间,约为R2柱的20%～30%;第24周,R1柱总氮和氨氮分别为206.5 mg/L和167.3 mg/L,在16～24周内,R1总氮和氨氮分别约为R2的14.5%～17.5%和36.2%～43.6%;18周时,R1柱总磷达最大值1.704 mg/L,至第24周降为0.673 mg/L, 整个实验过程R1柱总磷约为R2的0.15%～0.56%。     

反渗透处理稀土氨氮废水试验研究

根据稀土冶炼厂排放的碳铵沉淀洗涤废水的水质情况,采用NH4Cl和 NaCl模拟废水进行了反渗透可行性对比实验。模拟实验发现,在相同条件下反渗透对NaCl 较NH₄Cl 有着更高的去除率,而NH₄Cl 相对NaCl则有着更高的产水速率。实际废水试验结果表明,在恒定操作压力范围内回收率为65%的条件下,NH₄Cl浓度为2.85 g/L的碳铵沉淀洗涤废水经反渗透处理其NH₄Cl去除率为77.3%,可作为氨氮废水的预处理。对该废水处理成本进行了分析,得出其约为2.7元/m³,比相近浓度氨氮废水的氨吹脱处理成本节省约26%。     

高锰酸钾降解地下水中PCE的研究

以氯代有机污染物中常见的PCE为目标污染物,以自制高锰酸钾溶液为氧化剂,采用批实验方法,探讨了高锰酸钾降解PCE的反应动力学、影响因素以及反应机理。反应结果表明,高锰酸钾降解PCE的反应符合一级动力学方程,反应活化能E为57.119 kJ/mol,在30℃条件下,反应速率常数为0.0076 min^-1,半衰期为91.20 min。在pH在3～10,离子强度在0～0.1030 mol/L之间变化时,反应速率不受明显影响。     

超细粉煤灰基成型吸附剂的动态吸附实验

以粉煤灰为原料制备成型吸附剂,对水溶液中亚甲基蓝和Cr⁶⁺进行动态吸附研究,绘制穿透曲线,利用Origin软件对实验数据分析处理,得出穿透曲线的通式C_t=A₁－A₂〖〗1+(t/t₀)^p+A₁。结果表明,初始浓度C₀=25 mg/L,填料高度不同时,达到穿透点的时间随填料高度的增加而增加;填料高度h=200 mm,初始浓度不同时,达到穿透点的时间随初始浓度的增加而减小;该吸附剂对有机染料和重金属离子均有较好的吸附性能;穿透曲线通式的回归线性相关系数表明,该通式可很好地反映超细粉煤灰成型吸附剂的动态吸附过程。     

厌氧序批式反应器内挥发性脂肪酸积累特性研究

小试规模的厌氧序批式反应器（ASBR）,通过人工配水,研究了启动3个月时间以及一个运行周期内反应器内挥发性脂肪酸（VFA）的积累情况,并通过分析期间产甲烷活性的变化说明了控制VFA积累的重要性。经过近120 d的运行,乙酸和丙酸的最大比产甲烷活性分别提高了1.8和2.2倍,说明反应器的启动过程即是微生物群落的优化和选择的过程,ASBR的抗冲击的能力较强说明随启动的进行和种群的优化,活性污泥凝聚性能增强,对VFA的降解能力增强。     

One laptop per child,local refurbishment or overseas donations? Sustainability assessment of computer supply scenarios for schools in Colombia

With the intention of bridging the ‘digital divide’ many programmes have been launched to provide computers for educational institutions, ranging from refurbishing second hand computers to delivering low cost new computers. The fast and economical provision of large quantities of equipment is one of the many challenges faced by such programmes. If an increase is to be achieved in the sustainability of computer supplies for schools, not only must equipment be provided, but also suitable training and maintenance delivered. Furthermore, appropriate recycling has to be ensured, so that end-of-life equipment can be dealt with properly. This study has evaluated the suitability of three computer supply scenarios to schools in Colombia: (i) ‘Colombian refurbishment’, -refurbishment of computers donated in Colombia, (ii) ‘Overseas refurbishment’, -import of computers which were donated and refurbished abroad, and (iii) ‘XO Laptop’, -purchase of low cost computers manufactured in Korea. The methods applied were: Material Flow Assessment, -to assess the quantities-, Life Cycle Assessment, -to assess the environmental impacts, and the application of the Multiple Attribute Utility Theory, -to analyse, evaluate and compare different scenarios. The most sustainable solution proved to be the local refurbishment of second hand computers of Colombian origin to an appropriate technical standard. The environmental impacts of such practices need to be evaluated carefully, as second hand appliances have to be maintained, require spare parts and sometimes use more energy than newer equipment. Providing schools with second hand computers from overseas and through programmes such as ‘One Laptop Per Child’ has the disadvantage that the potential for social improvements – such as creation of jobs and local industry involvement – is very low.     

Mechanical Property Characterization of Plasticized Sugar Beet Pulp and Poly(Lactic Acid) Green Composites Using Acoustic Emission and Confocal Microscopy

Sorbitol and glycerol were used to plasticize sugar beet pulp-poly(lactic acid) green composites. The plasticizer was incorporated into sugar beet pulp (SBP) at 0%, 10%, 20%, 30% and 40% w/w at low temperature and shear and then compounded with poly(lactic acid) (PLA) using twin-screw extrusion and injection molding. The SBP:PLA ratio was maintained at 30:70. As expected, tensile strength decreased by 25% and the elongation increased. Acoustic emission (AE) showed correlated debonding and fracture mechanisms for up to 20% w/w plasticizer and uncorrelated debonding and fracture for 30–40% sorbitol and 30% glycerol content in SBP–PLA composites. All samples had a well dispersed SBP phase with some aggregation in the PLA matrix. However, at 40% glycerol plasticized SBP–PLA composites exhibited unique AE behavior and confocal microscopy revealed the plasticized SBP and PLA formed a co-continuous two phase system.

Enhancing community-based disaster preparedness with information technology

A critical component of community-based disaster preparedness (CBDP) is a local resource database of suppliers providing physical, information and human resources for use in disaster response. Maintenance of such a database can become a collaborative responsibility among community-based non-governmental organisations (NGOs) and public and private community organisations. In addition to mobilising resources, this process raises awareness within the community and aids in assessing local knowledge and resources. This paper presents the results of a pilot study on implementing a community-based resource database through collaboration with local American Red Cross chapters and public and private community organisations. The design of the resource database is described. The resource database is accessible via the internet and offline using laptops and handheld Personal Digital Assistants. The study concludes that CBDP is strengthened through a combination of appropriate information technology and collaborative relationships between NGOs and community-based organisations.     

The humanitarian common logistic operating picture: a solution to the inter‐agency coordination challenge

Although significant progress has been made in developing the practice of humanitarian logistics, further improvements in efficiency and effectiveness have the potential to save lives and reduce suffering. This paper explores how the military/emergency services’ concept of a common operating picture (COP) can be adapted to the humanitarian logistics context, and analyses a practical and proven approach to addressing the key challenge of inter‐agency coordination and decision‐making. Successful adaptation could provide the mechanism through which predicted and actual demands, together with the location and status of material in transit, are captured, evaluated, and presented in real time as the basis for enhanced decision‐making between actors in the humanitarian supply network. Through the introduction of a humanitarian logistics COP and its linkages to national disaster management systems, local communities and countries affected by disasters and emergencies will be better placed to oversee and manage their response activities.