危险废物回转窑焚烧系统的控制参数分析及调节方法研究

随着我国经济的迅速发展,危险废物产量持续增长,它们带来了严重的社会危害和环境危害。焚烧法是一种高温热处理技术,危险废物通过焚烧处理可实现无害化、减量化和资源化。回转窑焚烧系统具有处置范围广、处理量大、焚毁率高、安全可靠和可长期持续运行等特点,被国内外广泛应用。文章通过分析回转窑焚烧系统的主要控制参数,根据工程运行的实际经验,绘制了回转窑焚烧系统控制参数和焚毁率关系图,并提出了“最佳焚烧区域”的概念,对于回转窑焚烧系统的调试和运行工作,有积极的指导作用和重要的现实意义。     

论水处理工程中的节能

人们在污水处理厂的建设中对污水处理工艺的先进性、可靠性以及工程投资大小考虑较多,而对污水处理厂建成后的运营管理考虑较少,因而造成许多污水处理厂建成后由于运营成本过高而不能正常运行。从能耗角度出发,分析造成运行成本高的主要原因以及相应采取的措施。     

气相色谱法测定废水中6种挥发性脂肪酸含量

挥发性脂肪酸(VFA)是厌氧消化过程的重要中间产物,在反应器运行中,出水VFA用作重要的控制指标。通过色谱条件探索将各种脂肪酸分离,同时研究了水样酸碱度,吸附等对测定的影响,进一步优化了废水中挥发性脂肪酸的测定。方法的检出限在0.99~1.77 mg/L,回收率在90.9%~102.7%之间,相对标准差(n=5)在1.3%~3.8%之间。     

Effect of oxide-based fluxes on mechanical and metallurgical properties of Dissimilar Activating Flux Assisted-Tungsten Inert Gas Welds

Present investigation is to study the “Effect of Activating Fluxes on Mechanical and Metallurgical Properties of Dissimilar Activated Flux-Tungsten Inert Gas Welds”. Effect of current, welding speed, joint gap and electrode diameter on weld bead dimensions on 6 mm thick dissimilar weld between carbon steel to stainless steel, was studied under Activated Flux-Tungsten Inert Gas Welding process. During this investigation three different types of oxide powders were used-TiO₂, ZnO and MnO₂. After welding samples were subject to mechanical testing, in addition to characterization via micro hardness and microstructures of Normal Tungsten Inert Gas Welds and Activated Flux-Tungsten Inert Gas Welds. Activating fluxes TiO₂ and ZnO are effective fluxes for Activated Flux-Tungsten Inert Gas Welding of dissimilar weld between CS to SS. Highest depth/width (D/W) ratio reported under TiO₂ and ZnO fluxes compare to Normal-Tungsten Inert Gas Welds. Lowest angular distortion was observed under TiO₂ flux compare to Normal-Tungsten Inert Gas Welds. Mechanical properties, Joint Efficiency of Activated Flux-Tungsten Inert Gas Welds are higher than normal-Normal Tungsten Inert Gas Welds. Tensile Test specimens of both the processes failed from the parent metal (carbon steel side). Carbon migration from CS to SS, had occurred which led to failure of weld joints from CS side.     

Microstructure of 2205 duplex stainless steel joint in submerged arc welding by post weld heat treatment

The 2205 duplex stainless steel (DSS) is of both good properties austenitic steel and ferritic steel, which applies to the shipbuilding industry usually. In this paper, the OM, XRD and microhardness test methods are used to analyze the variation of submerged arc welded (SAW) joints with and without post weld heat treatment (PWHT). The research results show that the σ phase disappear in the fusion edge zone near heat affect zone (HAZ) and an increase in the welded center zone during the follow-up PWHT, while the amount of γ phase is decreased in the welded center zone with PWHT. A segregation distribution of some second phases is also found in the welded center zone after PWHT. There have two pick values of microhardness arise in the fusion edge zone and the welded center zone separately without PWHT. However, a maximum value of microhardness at the fusion edge zone near HAZ is disappeared and the other is still held at the welded center zone during PWHT. It can be attributed to the changes of second phases, element diffusions and particle segregation during PWHT. A developing mechanism is issued to demonstrate the second phases transferring of the 2205 DSS SAW joints by PWHT.     

茶叶基水合氧化铁吸附水体中Pb(Ⅱ)的性能

采用原位沉积技术将水合氧化铁(HFO)负载于废弃茶叶渣表面制备了复合材料茶叶基水合氧化铁(HFO-TW),研究了HFO-TW对水溶液中Pb(Ⅱ)的吸附特性,探讨了溶液pH值、时间、共存碱土离子、温度、Pb(Ⅱ)初始浓度等因素对Pb(Ⅱ)的吸附效果的影响.结果表明酸性范围内,Pb(Ⅱ)的吸附量随溶液pH升高而增大;Pb(Ⅱ)的吸附速度较快,100 min内便可达吸附平衡,且动力学曲线较好地符合伪一级和伪二级动力学模型,拟合系数可达98.8%;在竞争离子Ca(Ⅱ)/Mg(Ⅱ)的浓度高于Pb(Ⅱ)50倍时,HFO-TW对Pb(Ⅱ)仍具有较强的吸附能力,Pb(Ⅱ)的吸附量仅分别下降12.1 mg·g-1和8.1 mg·g-1;Pb(Ⅱ)的吸附过程较好地符合Langmuir等温模型,理论最大吸附容量为89.43 mg·g-1,远高于未经改性的茶叶渣和其他生物吸附剂.所有结果均证实HFO-TW在净化实际铅污染水体中有着较为广阔的应用潜力.     

中国危险废物和医疗废物焚烧处置行业二（口恶）排放水平研究

通过调研全国危险废物和医疗废物焚烧处置设施,对包含二噁英排放水平的设施按处置对象、炉型和处理量分类,并作系统分析和研究.结果表明现有危险废物焚烧设施烟气中二噁英的浓度比医疗废物低,达标率为74.19%;危险废物选用回转窑处置效果较好,达标率为66.67%;而医疗废物选用回转窑或热解炉,要综合考虑处置规模、生产成本和二英排放总量等因素;危险废物介于10~30 t·d-1和医疗废物介于10~20 t·d-1的处置设施要尤其注意二噁英的排放问题;医疗废物焚烧飞灰中二噁英的均值浓度为危险废物6倍以上,仅有16.67%满足填埋要求.二者烟气中二英的浓度分布以1,2,3,4,6,7,8-HpCDF、2,3,7,8-TCDF和OCDD为主.     

45~#钢在西双版纳大气环境下的腐蚀研究

目的研究西双版纳热带雨林地区大气环境下材料的初期腐蚀行为。方法使用45#碳钢在西双版纳大气环境下进行1年的大气暴露腐蚀试验,并利用质量损失分析、SEM、XRD和FTIR等技术,分析45#碳钢在西双版纳大气环境下暴露1年的腐蚀行为。结果 45#碳钢的腐蚀产物以γ-FeOOH,Fe(OH)3和Fe3O4为主,并有少量的α-FeOOH。结论西双版纳大气环境腐蚀性为C2级。在暴露1年的时间内,锈层化学稳定性随试验时间的延长逐渐增强,对基体的保护性逐渐加大。     

危险废物规范化管理措施研究

危险废物对人类和环境能产生极大的危害,具有"废物"和"资源"的双重属性。危险废物环境管理是从其产生、收集、贮存、转移、处置利用的全过程管理。文章阐述了危险废物的管理现状和特点,结合当前危险废物规范化管理面临的严峻形势,从完善法律法规体系、摸清危险废物底数、提升企业危险废物管理水平、推进危险废物处置项目建设、加强监管能力建设、加强宣传培训等方面提出了一些行之有效的合理化建议、对策,以更好地促进危险废物的管理工作。     

餐厨废弃物资源化利用与政府监管的探讨——以苏州市为例

以苏州市餐厨垃圾管理为例,从资源化处理、市场化运营模式与政府监管的角度出发,通过理论与实践相结合,对中国餐厨废弃物资源化利用的特点和现状进行分析,借鉴国内外先进工艺及管理经验,结合中国实施餐厨废弃物资源化利用和无害化处理地区的实施情况,指出并剖析在餐厨废弃物资源化不同处理模式中存在的问题,提出了加强餐厨废弃物管理的建议方案和对策.